System information

ManualsBrandsSimplex ManualsComputer equipment4190-9007

Features

Up to 250 addressable TrueAlarm or IDNet points**

Four, 2 A notification appliance circuits (NACs)

with solid state current protection

UL listed to Standard 864

Installation convenience features:

• Power-limited design with electronic modules

contained on one-piece chassis

• Up-front terminal blocks for wiring access

• Compact NEMA 1 rated cabinet is available in beige or

red and can be pre-shipped for early installation

Setup, programming, and maintenance features:

• Device level ground fault search, locate and isolate

• Auto Program, automatic module and device

programming for general alarm operation

• TrueAlarm individual analog sensing with front panel

information and selection access**

• “Dirty” TrueAlarm sensor maintenance alerts, service

and status reports including “almost dirty”

• Default TrueAlarm sensor device type operation

• Duplicate address error detection

• Front panel or PC programming

• TrueAlarm sensor peak value performance report

• WALKTEST™ silent or audible system test

†

• Software verification simulation mode

Supports the following IDNet devices** :

• Addressable manual stations

• Quad-state zone adapter modules (ZAMs) for initiating

device monitoring

• IDNet ground fault/short circuit isolator base for

TrueAlarm sensors

• Quad-state line powered individual addressable

modules (IAMs) for initiating device monitoring and

relay control

Available option modules include:

• Simplex 4120 Network, DACT, or City interface

• Equipment for Suppression Release Applications

(refer to data sheet S4010-0003)

• RS-232 ports for printers or maintenance terminal

• Class A NAC adapter module

• Additional power supply

Compatible with Simplex:

• TrueAlert™ Addressable Controllers and NAC power

extenders (IDNet controlled and conventional)

• 4003 Voice Control Panel

• 4081 Battery Cabinet with charger for 50 Ah batteries

† Simplex WALKTEST system test is protected under U.S. patent # 4,725,818.

4010 TrueAlarm Fire Alarm Control Panel

Description

TrueAlarm fire alarm control panels have the ability

to provide location accuracy for monitoring and control.

When equipped with TrueAlarm analog sensing for

smoke and heat detection, the processing power of the

control panel also has the ability to analyze conditions at

each location to provide accurate detection with

significantly reduced maintenance costs.

The Simplex 4010 TrueAlarm Fire Alarm Control Panel

has been specifically designed to provide addressable

operation and analog detection in a cost-effective package

for application sizes that previously were considered only

appropriate for conventional zoned monitoring.

Installation and Service Ease. The 4010 mounts on a

single chassis for quick installation and removal.

Terminal blocks are large and up-front for easy access

and inspection. Optional modules are easily and quickly

installed and programmed as required.

The 4010 cabinet provides convenient stud markers for

drywall thickness and nail-hole knockouts for quicker

mounting. Smooth cabinet surfaces are provided for

locally cutting conduit entrance holes exactly where

required. 4010 cabinets and electronics can be ordered

separately, allowing early cabinet installation.

Ground Fault Assistance. Ground fault problems

often occur during installation. The 4010 provides

isolating circuitry and software-controlled sequencing to

isolate ground faults to specific identified locations. This

assistance helps the installer to accurately locate the

wiring problem for quicker repair.

* This product has been approved by the California State Fire Marshal (CSFM) pursuant to

Section 13144.1 of the California Health and Safety Code. See CSFM Listing

7170-0026:226 for allowable values and/or conditions concerning material presented in this

document. It is subject to re-examination, revision, and possible cancellation. Accepted for

use – City of New York Department of Buildings – MEA35-93E. Additional listings may be

applicable, contact Simplex for the latest status.

** Simplex TrueAlarm analog smoke detection and IDNet addressable devices are

protected by one or more of the following U.S. Patents: 5,155,468; 5,173,683; 5,543,777;

5,400,014; 5,552,765; 5,552,763; DES. 377,460.

TrueAlarm

Fire Alarm Controls

UL, ULC Listed; FM, CSFM, and Model 4010 Fire Alarm Control Panel for

NYC, MEA Approved* TrueAlarm

Analog Sensors and IDNet™ Addressable Devices

Summary of content (8 pages)

PAGE 1
TrueAlarm® Fire Alarm Controls UL, ULC Listed; FM, CSFM, and Model 4010 Fire Alarm Control Panel for ® NYC, MEA Approved* TrueAlarm Analog Sensors and IDNet™ Addressable Devices Features Up to 250 addressable TrueAlarm or IDNet points** Four, 2 A notification appliance circuits (NACs) with solid state current protection UL listed to Standard 864 Installation convenience features: • Power-limited design with electronic modules contained on one-piece chassis • Up-front terminal blocks for wiring access • Comp
PAGE 2
4010 Operator Control Summary 4010 Display Panel and Diagnostic Mode Extensive Feature List. The Simplex 4010 Fire Alarm Control Panel provides access to an extensive feature list that includes: Convenient Status Information. With the locking door closed, a window allows viewing of the status display. The 4010 status panel provides a two line by 40 character, super-twist LCD information display and eight status LED indicators as shown in the illustration below.
PAGE 3
IDNet Addressable Interface can also be programmed as a utility device to monitor for temperature extremes in the range from 32° F to 155° F (0° C to 68° C). This feature can provide freeze warnings or alert to HVAC system problems. Overview. The 4010 provides IDNet addressable device communications.
PAGE 4
TrueAlarm Information Details True Alarm sensor data can be displayed on the system LCD, on a remote maintenance terminal, or printed on a remote printer. With the proper operator access, a TrueAlarm Service Report can be generated to list the specific details of each TrueAlarm device. This report, as well as the Status Report can either be displayed on the remote maintenance terminal or captured permanently by using a remote 80 character printer.
PAGE 5
Standard Panel Features media modules. May be both wired, both fiber optic, or one of each. N2 Communications for Serial Annunciator Control. Control for up to 6 remote Simplex Annunciator products including 24 Point I/O Module, and LCD Annunciator. Includes extensive troubleshooting diagnostics. DACT, Point Reporting Module. Provides serial output information that can send location details to a remote receiving station. DACT, Event Reporting Module.
PAGE 6
4010 Operating Specifications Input Power Requirements Voltage Range Frequency Maximum Current AC Input, 120 VAC base models 102 to 132 VAC 60 Hz 2A AC Input, 240 VAC base models 204 to 264 VAC 50/60 Hz 1A AC Input with 120 VAC expansion power supply 102 to 132 VAC 60 Hz 4A AC Input with 240 VAC expansion power supply 204 to 264 VAC 50/60 Hz 2A Environmental Operating Temperature Range 32° to 120°F (0° to 49° C) Operating Humidity Range up to 93% RH, non-condensing @ 100.
PAGE 7
4010 Fire Alarm Control Selection Chart and Module Location Rules (refer to diagrams on next page) Category Model* 4010-9101 4010-9102 Control Panel Assembly 4010-9201 (select one) 4010-9202 4010-9150 Description Voltage 4010 Fire Alarm Control Panel with: door, cabinet, power supply/battery charger, IDNet interface, 4 NACs, 2 auxiliary relays, and external N2 communications interface 120 VAC 240 VAC 4010 Fire Alarm Control Panel electronics only, for pre-shipped cabinets, requires door 120 VAC
PAGE 8
4010 Module Layout Reference BB+ — — — — TB1 AA+ SHLD NAC 4 — NAC 3 SHLD IDNet EXT N2 NAC 2 NAC 1 P2 TB3 4010-9809 or -9829 City Module 4010-9806 Class A Module FIRE ALARM SYSTEM SUPERVISORY SYSTEM TROUBLE ALARM SILENCED AC POWER ALARM ACK SUPV ACK TROUBLE ACK ALARM SILENCE SYSTEM RESET MENU FUNCTION DISABLE ENABLE EXIT CLEAR TB5 ENTER TB6 — AUX POWER TB7 NC C AUX1 NO NC 4010-9813, 4098-9814 4010-9823, or 4010-9824 Expansion Power Supply NEXT PREVIOUS 4010-9820