Installation guide

ManualsBrandsSimplex ManualsFire Alarms4100ES-S1

Specifications and other information shown were current as of publication and are subject to change without notice.

Simplex and the Simplex logo are trademarks of Tyco International Ltd. and its affiliates and are used under license.

574-836

Rev. N

4100/4120-Series Digital Alarm

Communications Transmitters

Installation Instructions

Introduction

This publication describes the installation procedure for the following:

•

4100/4120-0155 Serial Digital Alarm Communications Transmitter (DACT) (non-4100U/4100ES)

•

4100-6052 DACT (4100U/4100ES)

_________________________________________________________________________________

Documentation

•

Field Wiring Diagram for 4100 Power Limited (841-731) or,

•

Field Wiring Diagram for 4100 Non Power Limited (841-995)

•

4100ES Fire Alarm System Installation Guide (574-848)

•

T-Link TL250/TL300 Network Internet Alarm Communicator #29034631

•

C900V2 Installation Guide Dialer Capture Ethernet Module # F01U003472-02

_________________________________________________________________________________

Content

This publication covers the following topics:

Topic Page

Cautions and Warnings 2

Introduction 3

Power-Limited Wiring Guidelines 6

Connecting to the Phone Lines (not required when TL300 is used) 7

Configuring the DACT 8

Data and Power Wiring 10

Mounting 13

Programming 15

Testing 16

Compatibility 17

Summary of content (18 pages)

PAGE 1
4100/4120-Series Digital Alarm Communications Transmitters Installation Instructions Introduction This publication describes the installation procedure for the following: • 4100/4120-0155 Serial Digital Alarm Communications Transmitter (DACT) (non-4100U/4100ES) • 4100-6052 DACT (4100U/4100ES) _________________________________________________________________________________ Related Documentation • • • • • Field Wiring Diagram for 4100 Power Limited (841-731) or, Field Wiring Diagram for 4100 Non Power Li
PAGE 2
Cautions and Warnings Cautions and Warnings READ AND SAVE THESE INSTRUCTIONS. Follow the instructions in this installation manual. These instructions must be followed to avoid damage to this product and associated equipment. Product operation and reliability depend upon proper installation. DO NOT INSTALL ANY SIMPLEX® PRODUCT THAT APPEARS DAMAGED- Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage.
PAGE 3
Introduction Overview Digital Alarm Communications Transmitter’s (DACT) are option cards that mount within 4100 Fire Alarm Control Panels (FACP). The 4100/4120-0155 Serial DACT, available for the 4100 (non-4100U/4100ES) only, can be programmed to notify the central station when specified events occur, or to report changes to a specific point’s status.
PAGE 4
Introduction (continued) C900V2 Ethernet Transmission (UL only) The DACT receives system status messages from the 4100U/4100ES using the codes listed on page 17. It then communicates the information over an Ethernet connection to a DACR at the central station. The telephone connections on the DACT are connected together; R1 (TB1-2) to R2 (TB2-2) and T1 (TB1-3) to T2 (TB2-3). Then a single pair is connected to the C900V2.
PAGE 5
Introduction (continued) LEDs Refer to Table 1 for DACT LED indicators. Table 1. LED Indications LED Possible State Not Illuminated. The system is not receiving DC power, or the power-up self-test failed. Power (LED 1) Green LED On Steady. The DACT is receiving DC power and is operational. Flashing. DACT is dialing up (or attempting to dial up) the central station. Not Illuminated. No communication errors are being detected. On Steady. DACT cannot communicate with the Central Station.
PAGE 6
Power-Limited Wiring Guidelines Power-limited Wiring Guidelines • Non-power limited field wiring (AC power, batteries, City connection) must be installed and routed in the shaded areas shown in Figure 2. • Power-limited field wiring must be installed and routed in the non-shaded areas shown in Figure 2, with the exception of City wiring. • Excess slack should be kept to a minimum inside the back box enclosure.
PAGE 7
Connecting to the Phone Lines (not required when TL300 is used) Before Installation Have the telephone company install two telephone lines, each terminated with an RJ-31X jack immediately above or as close as possible to the fire alarm control panel. Be prepared to supply the telephone company with the FCC information printed on the FCC and/or Industry Canada label. Caution: Do not direct-connect the DACT to a coin telephone or party line.
PAGE 8
Configuring the DACT Overview Configuring the DACT consists of: • • • • Setting the correct communication mode Specifying whether the DACT is in Test mode Specifying whether the DACT should be ready to download new programming data Setting the device address This section covers all of these settings. Setting the COMM switch Make sure switch SW1 is in the DOWN position. This specifies the 4100 communications mode. Setting the Test Switch Make sure switch SW2 is in the DOWN (off) position.
PAGE 9
Configuring the DACT (Continued) Setting the address Table 3.
PAGE 10
Data and Power Wiring Wiring Guidelines Review the following guidelines before wiring P1 and P4 of the DACT. • If U.T. motherboard 565-274 or 565-213 is wired to the DACT, jumper P4 on the motherboard must be at position 13. • Unless otherwise noted, wiring is not supervised. • Cut and strip wire harnesses to the proper length, if required. Wiring an Serial DACT Card Into the System Note: Unless otherwise noted, wiring is not supervised. 1.
PAGE 11
Data and Power Wiring (Continued) Wiring the DACT to the TL300 Wire the DACT to the TL300 in accordance with Figure 6 and Figure 7. DSC FC5003 Cabinet T-Link TL300 12V GND TX Network GND BLK GRN PGM2 GND IN4 IN3 T1 GND Earth RX RED YEL IN2 R1 PGM1 IN1 #18 - #26 awg EOLR for IDC See note 3 #18 - #22 awg 3 #18 - #22 awg See note 2 #18-22 awg 150mA max See note 4 4 Notes: 1. Panel containing the TL300 to be mounted within 20 feet of the FACP and mounted in the same room.
PAGE 12
Data and Power Wiring (Continued) Wiring the DACT to the C900V2 DACT (UL only) %RVFK $( HQFORVXUH 6HH QRWH Figure 7 Notes: 3DQHO & 9 3 1. A Bosch C900V2 in a Bosch AE2 enclosure must be mounted within 20 feet of the FACP and be in the same room as it. The wiring to the FACP must be enclosed in the conduit or be equivalently protected against mechanical damage. The cabinet must be grounded.
PAGE 13
Mounting Overview Both assemblies are designed for different systems. • The 4100/4120-0155 Serial DACT mounts into a non-4100U/4100ES systems (with 297591xx Back Boxes). • The 4100-6052 DACT mounts into a 4100U/4100ES systems (with 2975-94xx Back Boxes). This section describes how to mount the cards into both types of bays. Mounting Serial DACT 4100/41200155 Use the instructions and figure below to mount a 4100/4120-0155 Serial DACT bracket into a 4100 Back Box (PID series 2975-91xx).
PAGE 14
Mounting (Continued) Mounting DACT 4100-6052 • The 4100-6052 DACT can only be installed in the CPU bay. • The DACT must be the leftmost assembly in the CPU bay. • See Figure 9. 1. Disconnect AC power at the source. Disconnect the + (red) wire from the battery. 2. Install harness 733-929 as shown. Connect from P1 on the DACT to the two 4-position connectors on the CPU motherboard. The blue wire to the top connector (P8) and the white wire to the bottom connector (P7). 3.
PAGE 15
Programming 4100/4120 Programming The DACT must be selected in the Programmer. Refer to Serial DACT Installation and Programming Instructions (574-090) for specific programming requirements. 4100U/4100ES Programming The correct DACT card must be selected in the 4100U/ES Panel Programmer. Refer to the ES Panel Programmer’s Manual (574-849). Additional Programming When a DACT connects to a TL300, additional programming is required. 1.
PAGE 16
Testing Testing When the DACT is connected to the system, its operations should be tested with the manual TEST switch (SW1). The manual test ensures that: • The phone line is working. • The DACT has been programmed with a correct phone number. • Communications with the central station work. When the manual switch is activated, the DACT dials the central station and transmits a "manual test" event code to the DACR located at the central station.
PAGE 17
Compatibility Compatibility Refer to Table 4 for compatibility information. Table 4. Compatibility information Comm.
PAGE 18
574-836 Rev.