User Manual

ManualsBrandsSimplex ManualsPower ExtenderSimplex Simplex 4009 NAC Power Extender

 1997 Simplex Time Recorder Co., Gardner, MA 01441-0001 USA

All specifications and other information shown were current as of publication, and are subject to change without notice

574-827

Rev. B

DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS

DAMAGED.

Upon unpacking your Simplex product, inspect the contents of the

carton for shipping damage. If damage is apparent, immediately file a claim

with the carrier and notify Simplex.

ELECTRICAL HAZARD -

Disconnect electrical power when making any

internal adjustments or repairs. Servicing should be performed by qualified

Simplex Representatives.

STATIC HAZARD -

Static electricity can damage components. Therefore,

handle as follows:

Ground yourself before opening or installing components.

Keep component wrapped in anti-static material at all times.

The Simplex 4009 NAC Power Extender (Figure 1) provides additional DC

signaling capacity to a Fire Alarm Control Panel (FACP) with a reverse polarity

Notification Appliance Circuit (NAC). The 4009 is UL-listed, electrically-

supervised, and protected against brown-out conditions and loss of primary AC

power.

Figure 1. Simplex 4009 NAC Power Extender

Continued on next page

Cautions and Warnings

Introduction

4009 NAC POWER EXTENDER

firealarmresources.com

Summary of content (12 pages)

PAGE 1
Cautions and Warnings DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED. Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify Simplex. ELECTRICAL HAZARD - Disconnect electrical power when making any internal adjustments or repairs. Servicing should be performed by qualified Simplex Representatives. STATIC HAZARD - Static electricity can damage components.
PAGE 2
Introduction, Continued The 4009 connects as an end-of-line device to a compatible, dedicated notification appliance circuit from the host panel (e.g., Simplex 4001 or 4002). It provides eight amperes of DC signaling power to either four or eight supervised reverse-polarity NACs, style Y or style Z. Alarms from the host panel signal the four (or eight) 4009 NACs to extend the alarm. The 4009 can also minimize transmission line losses associated with sending large currents long distances within buildings.
PAGE 3
Hardware Components, Continued 565-386 or 565-569 STYLE Y (CLASS B) SIGNAL CARD This module allows supervision of four Style Y (Class B) circuits with one signal circuit from a 4001, 4002, 4020, or 4100/4100+ (or any reverse polarity signal circuit operating at 24 VDC). It also accepts a +24V auxiliary alarm input, and can be supervised by the host FACP. All four signal circuit alarm relays energize with an alarm from the host signal circuit.
PAGE 4
Alarm Input Requirements When using 565-386 or 565-388 signal cards the alarm input from the host NAC must be 20 to 32 volts DC, with a maximum ripple voltage of 2 volts peakto-peak. When using 565-545 or 565-569 signal cards the alarm input from the host NAC must be 18 to 32 volts DC, unfiltered power supplies can be used. Alarm current for all signal card configurations is a maximum of 2 A at 24 VDC per circuit, and is power-limited.
PAGE 5
System Installation General Information Important: Notify the appropriate personnel (building occupants, fire department, monitoring facility, etc.) of the installation. The following paragraphs contain material which is applicable to all 4009 NAC Power Extender systems. Be sure that you are thoroughly familiar with this material before installing your 4009.
PAGE 6
System Installation, Continued Installation Checklist The installation checklist (shown in Table 1) provides a systematic method for installing the 4009. When you finish a procedural step, place a check mark in the appropriate box in the left column. Table 1. Installation Checklist PROCEDURE ; 1. Mount 4009 back box. 2. Install system wiring as required and check for absence of voltage, opens, and shorts. 3.
PAGE 7
System Installation, Continued Mounting the 4009 Note: The following pages provide a detailed description of the installation. If you experience problems that cannot be resolved, call your local Simplex Branch Office. Use the following procedure when mounting a 4009. 1. Carefully open the shipping container. 2. Remove the 4009 from the shipping container and lay the unit on a flat surface. 3. Unlock and open the panel door. 4. Remove the knockout plugs on the back box for wire entry. 5.
PAGE 8
Wiring the 4009 When wiring the 4009, refer to the 841-925 Field Wiring Diagram, the Wiring Information mounted on the inside of the 4009 panel door, the 4009 NAC Power Extender Connection Diagram (Figure 4), and the following system wiring requirements. • All wiring, except incoming power and ground connecting wires, must be free from grounds or shorts and have a resistance of one megohm, or higher, to EARTH. • All wires are to be copper conductors only.
PAGE 9
Mounting and Wiring Peripheral Devices Note: Use the resistor color code shown in Figure 5 to identify the End-ofLine Resistors used in the installation. Refer to the 841-925 Field Wiring Diagram and the procedure listed below when installing the 4009 peripheral devices. 1.
PAGE 10
System Wiring Configurations The 4009 has the following system wiring configurations: • Style Y (Class B) • Style Z (Class A) • Interconnection to Host Panel, Single Signal Card • Interconnection to Host Panel, Two Signal Cards • Interconnections as a Single Reverse Polarity Device (single or two signal card(s), isolated or non-isolated configuration Notes: 1. 2.
PAGE 11
Jumper Placements and Terminal Connections (continued) 8. When 565-558 Earth Detect Module is not used, and on non-isolated systems, install an 12 AWG copper wire from TB2-3 on the 565-367 and 565-488 power supply to 0V on the battery block of the host FACP. 9. Apply system power. 10. If using internal batteries, connect as indicated. 11. If using external batteries from FACP, connect as indicated. 12. Test the system. 11 firealarmresources.
PAGE 12
574-827 Rev. B firealarmresources.