Biometric Transponder: TRA.FP.
Biometric Transponder: TRA.FP.INF2 Content 1.0 2.0 General Instructions .....................................................................3 1.1 Safety instructions................................................................................ 3 1.2 Product description .............................................................................. 4 Overview of function.....................................................................5 2.1 Basic information on operation.........................
Biometric Transponder: TRA.FP.INF2 Page 3 1.0 General Instructions Please take 15 minutes to familiarise yourself with how your Biometric Transponder works with the help of these operating instructions. Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Biometric Transponder: TRA.FP.INF2 Page 4 1.2 o Programming should only be carried out by trained specialist staff. o SimonsVoss Technologies, Inc. is not liable for any damage caused by incorrect programming. o An incorrectly programmed or faulty transponder can block access through a door. SimonsVoss Technologies, Inc. is not liable for the consequences of such an occurrence, such as blocked access to persons who are injured or in danger, material damage or any other damage.
Biometric Transponder: TRA.FP.INF2 Page 5 2.0 Overview of function 2.1 Basic information on operation The Biometric Transponder scans fingerprints using a fingerprint sensor. The finger is dragged across the sensor, rather than being pressed against it. The following should be noted: The fingerprint to be scanned and memorized should always be dragged over the sensor in the same way.
Biometric Transponder: TRA.FP.INF2 Page 6 2.3 How the transponder works Stand-by mode: LED not illuminated Briefly press button once, then release Recognize mode: LED flashes green Press button and hold down for 3 sec. Drag finger across sensor Transponder triggered Learn mode: LED flashes yellow Press button and hold down for 3 sec. Drag Administrator finger once over sensor and new finger (User finger) 3 times over sensor.
Biometric Transponder: TRA.FP.INF2 Page 7 Please note: The first two fingerprints scanned in are automatically the Administrator fingerprints. Without them, no further fingerprints can be scanned in or deleted later! To scan in and store the first Administrator fingerprint (e.g. left thumb), please do the following: 1. Briefly press the transponder button; the LED will flash green. 2. Then press the button again and hold it pressed for at least 3 seconds (until the LED flashes yellow). 3.
Biometric Transponder: TRA.FP.INF2 Page 8 Scanning more fingerprints (User fingerprints) Further fingerprints (maximum 4 beyond the initial 2) can be scanned in as the Administrator fingerprints have been, except that the Biometric Transponder must first be cleared for this by an Administrator fingerprint. This prevents unauthorized persons from scanning in their own fingerprints and thus gaining access rights that are not allowed.
Biometric Transponder: TRA.FP.INF2 Page 9 2.5 Querying the number of fingerprints scanned in You can discover the number of fingerprints already entered as follows: 1. Press the button once briefly (the LED flashes green) 2. Press the button again and hold it down for 1.5 to 2 seconds (not as long as 3 seconds, which will take you into "learn" mode). 3. The LED flashes red. 4. Then the LED will flash green as many times as the number of fingerprints entered (maximum of 6). 5.
Biometric Transponder: TRA.FP.INF2 Page 10 2.6 "Recognize" mode: single triggering of transponder The mode known as the Recognize mode is the normal operating state for the Biometric Transponder. This mode is entered when a person whose fingerprint has been authorized would like to open a door protected by a SimonsVoss RF lock. To do this, proceed as follows: 1. Press the button of the Biometric Transponder briefly (for around 0.5 sec.), and the LED will then flash green. 2.
Biometric Transponder: TRA.FP.INF2 Page 11 3.0 "Delete" mode: deleting fingerprints Both individually scanned fingerprints and all the fingerprints can be deleted from the memory. If normal fingerprints (not Administrator fingerprints) are deleted, the other fingers that have been scanned in are not deleted. No Administrator fingerprint is needed to do this (any normal user can delete his own fingerprint).
Biometric Transponder: TRA.FP.INF2 Page 12 5.0 Programming the Transponder with the SimonsVoss software The "Set validity" function and the "Quasi-proximity mode" are not available for the Biometric Transponder. 6.0 Changing the Batteries To replace the batteries, push the battery cover downwards and remove. Take out all the batteries and replace with new ones. Make sure that the polarity is correct (stamped into the base of the battery compartment).
Biometric Transponder: TRA.FP.INF2 Page 13 7.0 Technical Data Dimensions: H x W x D 2.8 x 1.3 x 0.7 in (265 x 32 x18 mm) Weight 0.8 oz (22 g) Colour Dark Grey, with blue button Operating distance, locking cylinders approx. 16 inches (40 cm) if the transponder, lengthways, is held parallel with the cylinder antenna. Operating distance, Smart Relay approx. 47 inches (120 cm) if the transponder is parallel with the antenna of the SmartRelay.
Biometric Transponder: TRA.FP.INF2 Page 14 8.0 Table of Diode Signals LED Mode off Standby off moving finger on sensor followed by comparison with scanned fingerprint, please wait (max. 4 seconds) Slow green flashing light Recognize mode, wait for finger (max. 30 seconds) Fast green flashing light Release for transparent mode, wait for finger (max.