Tus neeg siv phau ntawv

Note:
• The transmitter will automatically enter standby mode within 5 minutes of no
signal input, and it will automatically restart when there is an audio signal input.
HOW TO USE
SM-828D1 / SM-828D2 is compatible with OPTICAL output, RCA (labeled
AUDIO OUT) and AUX 3.5mm output.
2.1 Power the Transmitter (Ref. Fig 2-1)
Plug the supplied AC adapter into a standard electrical outlet, plug the other end
of the AC adapter into the port labeled “DC 5V” on the back of the transmitter.
2. Turn on the Transmitter and Earphone
1. Check Your TV/Audio Source Output Options before the Set up
Note:
• Three different audio cables included: digital optical cable, RCA cable and
3.5mm cable. In the end, only one of these cables is needed to complete the
installation.
• The earphone will power off automatically after 10 minutes of no audio signal
in. Using it again, you need to slide ON/OFF switch to “OFF” position, then
slide to “ON.
• If your audio source device has an optical audio out port, please connect
SIMOLIO to this port preferentially. If not, you can also connect SIMOLIO to
the RCA or AUX/ 3.5mm or other audio out port of the audio source device.
Other RCA
jacks(usually
audio in)
AUDIO IN
Digital Optical
AUDIO OUT
OPTICAL
AUDIO OUT
(need extra 6.35mm
to 3.5mm adapter,
purchase separately)
(need extra digital to
analog converter,
purchase separately)
Digital
AUDIO OUT
Coaxial
COAXIAL
Jack
Options
Natively
supported?
Please
referto Point
6.35mm
Phone jack
PHONE
3.1
AUX/3.5mm
3.3
RCA jacks
labeled
AUDIO OUT
R
L
AUDIO OUT
3.2
N/A
3.4 3.4
Fig 1-1
R
L
3.1 Digital Optical Connection
This part will instruct you on how to connect the
SM-828D2 transmitter to your television, satellite, or cable box using an optical
digital audio cable.
SIMOLIO SM-828D1 /
2.2 Turn on the Transmitter (Ref. Fig 2-2)
Slide MONO/STEREO/OFF switch to
MONO” or “STEREO” position.
2.3 Turn on the
Slide ON/OFF switch to “ON” position .
Earphone (Ref. Fig 2-3).
Note: Please charge the for
3 hours before using it for the first time.
earphone
3.Connect the Transmitter to Your TV/Audio Source
Set the volume of the audio source to a level sufficient for people with normal
hearing to clearly listen to the TV to ensure stable audio output.
i.e. set the TV box VOL 30 % & TV VOL 40% (Ref. Fig 3-1) (Ref. Fig 3-2)
For watching TV quietly without disturbing others, the right way is: Mute your
TVby pressing the MUTE button on the remote control or choose any speaker
option other than TV Speaker in the TV Sound Output settings.(Ref. Fig 3-3)
• The above settings may differ from various TVs.
TV box VOL 30 %
Fig 3-1
Mute
Fig 3-3
TV VOL 40 %
Fig 3-2
Fig 2-2
Power in
Power adapter
Transmitter
Fig 2-1
STEREO
MONO
OFF
DC 5V
PO
WER
DC 5V
IN
P
O
WER
DC 5V
AUX
STERE
O / MONO / O
FF
OPTI CAL
OPTI CAL
AUX
IN
OUT
ON / OFF
STEREO
MONO
OFF
ON / OFF
ON/OFF
Fig 2-3
ON/OFF
06 07
SM-828D1/SM-828D2 SM-828D1/SM-828D2
+ VOL -
L
R