User's Manual

06 07
Note:
• The transmitter will automatically enter standby mode within 5 minutes of no
signal input, and it will automatically restart when there is an audio signal input.
HOW TO USE
SM-824D1 / SM-824D2 is compatible with OPTICAL output, RCA (labeled
“AUDIO OUT”) and AUX 3.5mm output.
2.1 Power the Transmitter (Ref. Fig 2-1)
Plug the supplied AC adapter into a standard electrical outlet, plug the other end
of the AC adapter into the port labeled “DC 5V” on the back of the transmitter.
2. Turn on the Transmitter and Headset
1. Check Your TV/Audio Source Output Options before the Set up
Note:
• Three different audio cables included: digital optical cable, RCA cable and
3.5mm cable. In the end, only one of these cables is needed to complete the
installation.
• The headphone will power off automatically after 10 minutes of no audio signal
in. Using it again, you need to slide ON/OFF switch to “OFF” position, then slide
to “ON”. Be aware, the headphone will not automatically power off in the personal
sound amplifier mode unless the battery is dead.
• If your audio source device has an optical audio out port, please connect
SIMOLIO to this port preferentially. If not, you can also connect SIMOLIO to the
RCA or AUX/3.5mm or other audio out port of the audio source device.
SM-824D1/SM-824D2 SM-824D1/SM-824D2
Other RCA
jacks(usually
audio in)
AUDIO IN
Digital Optical
AUDIO OUT
OPTICAL
AUDIO OUT
(need extra 6.35mm
to 3.5mm adapter,
purchase separately)
(need extra digital to
analog converter,
purchase separately)
Digital
AUDIO OUT
Coaxial
COAXIAL
Jack
Options
Natively
supported?
Please refer
to Point
6.35mm
Phone jack
PHONE
3.1
AUX/3.5mm
3.3
RCA jacks
labled
AUDIO OUT
R
L
AUDIO OUT
3.2
N/A
3.4 3.4
Fig 1-1
R
L
3.1 Digital Optical Connection
This part will instruct you on how to connect the SIMOLIO
SM-824D2 transmitter to your television, satellite, or cable box using an optical
digital audio cable.
SM-824D1/
2.2 Turn on the Transmitter (Ref. Fig 2-2)
Slide OFF/MONO/STEREO switch to “MONO” or “STEREO” position.
2.3 Turn on the Headset
Slide ON/OFF switch to “ON” position .
(Ref. Fig 2-3).
Note: Please charge the headset for 3 hours before using it for the first time.
3.Connect the Transmitter to Your TV/Audio Source
Set the volume of the audio source to a level sufficient for people with normal
hearing to clearly listen to the TV to ensure stable audio output.
i.e. set the TV box VOL ≥ 30 % & TV VOL ≥ 40% (Ref. Fig 3-1) (Ref. Fig 3-2)
For watching TV quietly without disturbing others, the right way is: Mute your TV
by pressing the MUTE button on the remote control or choose any speaker option
other than TV Speaker in the TV Sound Output settings.(Ref. Fig 3-3)
ON OFF
Fig 2-2
Fig 2-3
ON
VO
L
B
A
L
OFF
L
R
L
H
Power in
Power adapter
Transmitter
• The above settings may differ from various TVs.
TV box VOL ≥ 30 %
Fig 3-1
Mute
Fig 3-3
TV VOL ≥ 40 %
Fig 3-2
Fig 2-1
ST
ER
EO
M
ON
O
OFF
O
FF
/ON
DC 5V
P
O
WER I
N
BA
SS
T
RE
B
LE
N
OR
MA
L
S
T
ER
E
O
TO
NE
A
UD
IO IN
MO
NO
OF
F
DC 5
V
O
FF/O
N
P
O
W
E
R I
N
OPTIC A
L IN