User's Manual
Table Of Contents
- Contents
- Table Index
- Figure Index
- 1Introduction
- 1.1Product Outline
- 1.2Hardware Interface Overview
- 1.3Hardware Block Diagram
- 1.4Functional Overview
- 2Package Information
- 2.1.Pin Assignment Overview
- 2.2.Pin Description
- 2.3.Mechanical Information
- 2.4.Footprint Recommendation
- 3Interface Application
- 3.1Power Supply
- 3.3UART Interface
- 3.4USB Interface
- 3.5SIM Interface
- 3.6PCM Interface
- 3.7I2C Interface
- 3.8SPI Interface
- 3.9Network status
- 3.10ADC interface
- 3.11LDO output
- 3.12USB_BOOT Interface
- 3.13GPIO Interface
- 3.14 RF control Interface
- 3.15Force USB Download Interface
- 4RF Specifications
- 4.1LTE RF Specifications
- 4.2LTE Antenna Design Guide
- 4.3GNSS
- 4.4RF traces note
- 5 Electrical Specifications
- 5.1Absolute maximum ratings
- 5.2Operating conditions
- 5.3Operating Mode
- 5.4Current Consumption
- 5.5ESD Notes
- 6 SMT Production Guide
- 6.1Top and Bottom View of SIM7090G
- 6.2Label Information
- 6.3Typical SMT Reflow Profile
- 6.5Baking
- 6.6Stencil Foil Design Recommendation
- 7 Packaging
- 7.1Tray packaging
- 8 Appendix
- 8.1Coding Schemes and Maximum Net Data Rates over Air
- 8.2Related Documents
- 8.3Terms and Abbreviations
- 8.4Safety Caution
IC Warning
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1)
This device may not cause interference, and
(2)
This device must accept any interference, including interference that may cause
undesired operation of the device.
The modular can be installed or integrated in mobile or fix devices only. This
modular cannot be installed in any portable device.
IC Radiation Exposure Statement
This modular complies with IC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. This modular must be installed and
operated with a minimum distance of 20 cm between the radiator and user body.
For a host manufacture's using a certified modular, if (1) the module's IC
number is not visible
when installed in the host, or (2) if the host is marketed so that end users do not
have straightforward commonly used methods for access to remove the module so
that the IC number of the module is visible; then an additional permanent label
referring to the enclosed module: "Contains Transmitter Module IC: " 23761-
8VC0003 " or "Contains IC: 23761-8VC0003 " must be used.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement
Le modular peut être installé ou intégré dans un mobile ou réparer une seule chose
Installation dans n’importe quel appareil portable.
Déclaration de rayonnement IC
Ce modular complies avec des radiations émettrices de rayonnement Environnement.
Ceci ne doit pas être co-localisé ou opérer avec des autres Ce modular doit être
installé et obtenu avec une distance minimale de 20 cm entre les radiateurs et le
corps de l’utilisateur.
Pour un hôte, on utilise un modular, si (1) le numéro de module est non visible
Quand on est installé dans le serveur, or (2) si le propriétaire est commercialisé
Straightforward commonly used for the access to remove travail so that the number
IC en vue Le module est visible; Ensuite, le label permanent a été attribué au module:
"Contient le Module IC:" 23761-8VC0003" ou "contenu IC: 23761-8VC0003" doit" be
used