User's Manual
Table Of Contents
- Contents
- Table Index
- Figure Index
- 1Introduction
- 1.1Product Outline
- 1.2Hardware Interface Overview
- 1.3Hardware Block Diagram
- 1.4Functional Overview
- 2Package Information
- 2.1.Pin Assignment Overview
- 2.2.Pin Description
- 2.3.Mechanical Information
- 2.4.Footprint Recommendation
- 3Interface Application
- 3.1Power Supply
- 3.3UART Interface
- 3.4USB Interface
- 3.5SIM Interface
- 3.6PCM Interface
- 3.7I2C Interface
- 3.8SPI Interface
- 3.9Network status
- 3.10ADC interface
- 3.11LDO output
- 3.12USB_BOOT Interface
- 3.13GPIO Interface
- 3.14 RF control Interface
- 3.15Force USB Download Interface
- 4RF Specifications
- 4.1LTE RF Specifications
- 4.2LTE Antenna Design Guide
- 4.3GNSS
- 4.4RF traces note
- 5 Electrical Specifications
- 5.1Absolute maximum ratings
- 5.2Operating conditions
- 5.3Operating Mode
- 5.4Current Consumption
- 5.5ESD Notes
- 6 SMT Production Guide
- 6.1Top and Bottom View of SIM7090G
- 6.2Label Information
- 6.3Typical SMT Reflow Profile
- 6.5Baking
- 6.6Stencil Foil Design Recommendation
- 7 Packaging
- 7.1Tray packaging
- 8 Appendix
- 8.1Coding Schemes and Maximum Net Data Rates over Air
- 8.2Related Documents
- 8.3Terms and Abbreviations
- 8.4Safety Caution
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)
This device may not cause harmful interference, and
(2)
this device must accept any interference received, including interference that
may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
The modular can be installed or integrated in mobile or fix devices only. This
modular cannot be installed in any portable device.
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. This modular must be installed and
operated with a minimum distance of 20 cm between the radiator and user body.
If the FCC identification number is not visible when the module is installed inside
another device, then the outside of the device into which the module is installed
must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains Transmitter
Module FCC ID: 2AJYU-8VC0003 Or Contains FCC ID: 2AJYU-8VC0003”
When the module is installed inside another device, the user manual of the host
must contain below warning statements;
1.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)
This device may not cause harmful interference.
(2)
This device must accept any interference received, including interference that
may cause undesired operation.
2.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the product.
Any company of the host device which install this modular with limit modular
approval should perform the test of radiated emissionand spurious emission
according to FCC Part 22H and 24E, 47 CFR Part 2, 22H, 24(E), 27 and 47 CFR
Part 2, 22H, 24(E), 27, 90 requirement,Only if the test result comply with FCC Part
22H and 24E, 47 CFR Part 2, 22H, 24(E), 27 and 47 CFR Part 2,22H, 24(E), 27, 90
requirement, then the host can be sold legally.