User's Manual
Table Of Contents
- Contents
- Table Index
- Figure Index
- 1Introduction
- 1.1Product Outline
- 1.2Hardware Interface Overview
- 1.3Hardware Block Diagram
- 1.4Functional Overview
- 2Package Information
- 2.1.Pin Assignment Overview
- 2.2.Pin Description
- 2.3.Mechanical Information
- 2.4.Footprint Recommendation
- 3Interface Application
- 3.1Power Supply
- 3.3UART Interface
- 3.4USB Interface
- 3.5SIM Interface
- 3.6PCM Interface
- 3.7I2C Interface
- 3.8SPI Interface
- 3.9Network status
- 3.10ADC interface
- 3.11LDO output
- 3.12USB_BOOT Interface
- 3.13GPIO Interface
- 3.14 RF control Interface
- 3.15Force USB Download Interface
- 4RF Specifications
- 4.1LTE RF Specifications
- 4.2LTE Antenna Design Guide
- 4.3GNSS
- 4.4RF traces note
- 5 Electrical Specifications
- 5.1Absolute maximum ratings
- 5.2Operating conditions
- 5.3Operating Mode
- 5.4Current Consumption
- 5.5ESD Notes
- 6 SMT Production Guide
- 6.1Top and Bottom View of SIM7090G
- 6.2Label Information
- 6.3Typical SMT Reflow Profile
- 6.5Baking
- 6.6Stencil Foil Design Recommendation
- 7 Packaging
- 7.1Tray packaging
- 8 Appendix
- 8.1Coding Schemes and Maximum Net Data Rates over Air
- 8.2Related Documents
- 8.3Terms and Abbreviations
- 8.4Safety Caution
Antenna requirements
1.
Antenna List:
Type: vehicle antenna with standard SMA connector(50ohm);
Model: MF25D
Antenna Gain:
2.
The user must match the MF25D antenna with the non-standard SMA
connector and cannot change the antenna.
This device is intended only for OEM integrators under the following
conditions: (For module device use)
1)
The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2)
The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their end-
product for any additional compliance requirements required with this module
installed.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator & your body.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes:
(Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre
l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur
ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais
sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce
module installé.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.
B2/B4/B25:3dBi B5/B12/B13/B26/B71: 2dBi