User's Manual
Table Of Contents
- Contents
- Table Index
- Figure Index
- 1Introduction
- 1.1Product Outline
- 1.2Hardware Interface Overview
- 1.3Hardware Block Diagram
- 1.4Functional Overview
- 2Package Information
- 2.1.Pin Assignment Overview
- 2.2.Pin Description
- 2.3.Mechanical Information
- 2.4.Footprint Recommendation
- 3Interface Application
- 3.1Power Supply
- 3.3UART Interface
- 3.4USB Interface
- 3.5SIM Interface
- 3.6PCM Interface
- 3.7I2C Interface
- 3.8SPI Interface
- 3.9Network status
- 3.10ADC interface
- 3.11LDO output
- 3.12USB_BOOT Interface
- 3.13GPIO Interface
- 3.14 RF control Interface
- 3.15Force USB Download Interface
- 4RF Specifications
- 4.1LTE RF Specifications
- 4.2LTE Antenna Design Guide
- 4.3GNSS
- 4.4RF traces note
- 5 Electrical Specifications
- 5.1Absolute maximum ratings
- 5.2Operating conditions
- 5.3Operating Mode
- 5.4Current Consumption
- 5.5ESD Notes
- 6 SMT Production Guide
- 6.1Top and Bottom View of SIM7090G
- 6.2Label Information
- 6.3Typical SMT Reflow Profile
- 6.5Baking
- 6.6Stencil Foil Design Recommendation
- 7 Packaging
- 7.1Tray packaging
- 8 Appendix
- 8.1Coding Schemes and Maximum Net Data Rates over Air
- 8.2Related Documents
- 8.3Terms and Abbreviations
- 8.4Safety Caution
SIM7090G User Manual V1.01
www.simcom.com
3
/
77
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
RF warning:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
IC Caution:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1)
This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Ce matériel est complété par une exposition de rayonnements IC pour un environnement naturel. Ce
matériel doit être installé et se faire avec une distance minimale de 20cm entre les radiateurs et les
autresYour body shop.
For a host manufacture’s using a certified modular, if (1) the module’s IC number is not visible when
installed in the host, or (2) if the host is marketed so that end users do not have straightforward
commonly used methods for access to remove the module so that the IC number of the module is
visible; then an additional permanent label referring to the enclosed module: “Contains Transmitter
Moducle IC: 23761-8VC0003” or “Contains IC: 23761-8VC0003” must be used.
This radio transmitter IC: 23761-8VC0003 has been approved by Imovation,Sience and Economic
Development Canada to operate with the antenna types listed below,with the maximm permissible gain
indicated.Antenna types not included in this list that have gain greater than the maximm gain indicated for
any type listed are strictly prohibilted for use with this device.