DOMINO 55M cod. 46.0471.
KEYPAD ▲, ▼, ◀, ▶ MENU Navigate through and make adjustments to the on screen menus. Activates the On Screen Display menus. Navigates menu pages. ▲, ▼ SOURCE switches on from stand-by and calls the Input Selection menu. ���� Switches the unit to stand-by. ▶ INFO (if pressed in the absence of the On Screen Display) calls the INFO information window. ◀ AUTO (if pressed in the absence of the On Screen Display) calls Auto Adjust (automatic optimisation of the image).
1 INTRODUCTION The new DOMINO 55M offers an image without any compromise, with resolution, sharpness, colorimetry and contrast au par with the one of renowned SIM2 front projector line. Conversion of interlaced video signals to progressive signals by means of prestigious DCDi™ technology produces fluid, natural images free of artifacts such as flicker and stairstepping on diagonals.
2 IMPORTANT SAFETY INSTRUCTIONS This symbol indicates the possible electric shock hazard associated with uninsulated live components in the interior of the unit. ATTENTION: To reduce the risk of electric shock, disconnect the power supply cable on the rear panel before removing front (or back) panel of the unit. No user-serviceable parts inside. Refer to trained, authorised personnel for technical assistance.
is damaged, unplug the unit from the wall outlet and request the assistance of an authorised technician. • Unplug the unit from the mains power supply during a lightning storm and when not in use. To avoid damage to the unit due to lightning and power-line surges, unplug the unit in the event of electrical storms or when the unit is left unused for long periods of time. • Avoid contact with liquids and exposure to humidity. Do not use the unit near water (sinks, tanks, etc.
CONTROL NT CE 8� REMOTE CONTROL The remote control transmits commands to the system by infrared signals. The infrared sensor is on the front panel of the DOMINO 55M. Avoid placing obstructions between the remote control and the infrared sensor; this will impair the remote control performance. The remote control requires four 1.5V AAA alkalin e batteries. Insert the batteries, taking care to match the polarity, as indicated in the battery compartment in the handset (Fig. 2).
VIDEO 1 Table 1 This input should be connected to a Composite Video signal (CVBS) by means of a cable with an RCA connector. The connector on the source is usually yellow and is frequently labelled VIDEO. Although other types of signals are preferable (since they allow better picture quality), Composite Video signal is still very common, and nearly all television receivers, video-recorders, DVD players, camcorders, etc., are equipped with it.
� � �������������� � �������������� 3 ����� V HV ������� B/ Cb ��������������� Y G/ 1 C R/ EO r 4 VID V ������������ HV Cb B/ O DI AU T OU Y G/ 2 S- N CO O TR RS L( 2) 23 Cr R/ O E VID 5 � � B RG S IC PH RA G ���� 7 T PU IN D 6 IDV � ������������ � ����� Fig.
4 SWITCHING ON AND OFF DOMINO 55M power switch is on the rear panel (Fig.5). STAND BY Switching On (Fig.6): ME NU O I Fig.5 Once the power switch is on the “I” position, the unit will initialise and execute a test routine. Soon after the unit will enter stand-by mode (Table 2). Front panel LEDs placed show the status of the unit. Table 2 ������ ��������� ������� ��� �������������� Fig.
If you wish to power off the unit completely, wait at least one minute in stand-by to allow the unit to cool before setting the mains power switches to the “O” position or unplugging the power supply cables. 5 ON SCREEN MENU All the functions of the DOMINO 55M can be activated from the keypad or remote control with the aid of a practical and comprehensive system of on screen menus.
PICTURE Picture Brightness 60 Contrast Color Tint Sharpness Filter Cinema Mode Video Type Noise Reduction 50 50 50 3 2 Off Normal Auto This menu features the adjustments related to picture quality. Adjustments that are not available for a specific input will not be displayed on the menu. Table 3 summarises the adjustments available for each input. Auto VCR1 VCR2 Fig. 9 For others (e.g.
CINEMA MODE This control selects the deinterlace algorithm applied to the input signal. Select AUTO mode to analyse signal characteristics and apply the correct deinterlace mode automatically. Use this option if the video signal source is a movie film (obtained from a Teleciné device with 3:2 or 2:2 pull-down). Select NO to apply a Motion compensated algorithm optimized for video camera signals. VIDEO TYPE This control inserts a filter that improves stability of images from videorecorders or DVD players.
PANORAMIC: stretches the 4:3 image, slightly cropping the upper and lower parts. Panoramic is ideal for displaying a 4:3 image on the 16:9 screen of the Display. (no overscanning) and 32 (maximum overscanning). The resulting image always maintains the selected aspect irrespective of the selected overscan value. PIXEL TO PIXEL: displays the image as it is input without adapting it to the screen.
Table 4 MENU �������� ����� ����� ������������� ������ ����� ���������� ����������� ����������� ����� ������� ����� � ������ ��������� � � � ����� � � � ����������������� ����������������� �������� ��������� � � � � SETUP The setup menu contains less frequently used adjustments that may be required during installation (e.g. the display of Test Patterns).
���������������� ��������������������� ������ ������� � � ����� � ���� � ���� � ��� � ���� � ��� � ���� � ���� � ���� � OSD POSITION Serves to position the On Screen Display within the screen area. The OSD can be positioned using the arrow keys for fine adjustments or keys 1...9 on the remote control to select one of 9 preset positions. MEMORIES � � Fig.13 Text input mode is same whether you are editing an existing name or entering a name for the first time.
key on the remote control (Fig.14) serves to activate Pressing the the menus management menu page. memory is associated with the specific source and signal type and called automatically whenever that specific combination of source and signal type is selected. SAVE INITIAL SETTINGS IN MEMORIES 20 To restore the original values of a previously modified Memory, select the line relative to the Memory in question and open the corresponding drop-down menu ( ◀ key). Select the line SAVE INITIAL SETTINGS.
DIRECT-ACCESS ADJUSTMENTS MESSAGES FREEZE Allows you to freeze the displayed image (press remote control key). Press the key once again to restore normal viewing . The following messages may appear during operation of the unit: MAGNIFICATION Allows you magnify a selected area of the image. The degree of enlargement is selected in Zoom mode (identified by the symbol in the centre of the image) using the ◀ and ▶ keys.
7 TROUBLESHOOTING GUIDE No power (LEDs always OFF) • • • • Check that the units’ power switches are set to ‘I’. Check that the power cables are correctly connected to the unit power sockets. Check the condition of the fuse located on the power socket on the rear of the unit. Replace the fuse located on the unit power socket with an equivalent and identically rated fuse (T3.15A H). Lamp fails to switch on • • Allow a few minute pause between switching off and switching on again.
8 ADDITIONAL INFORMATION A TECHNICAL SPECIFICATIONS OPTICS Optical system: DMD™ panel: Projection Lens: Color Wheel: Lamp: Picture size: Contrast: optical engine based on 1 DMD™ chip; sea led dust-proof housing TI HD2+ 0,8” 12° Dark Metal - 1280x720 pixel (16:9 aspect ratio) UltraWide angle F/2.
B DIMENSIONS ��� ��� ���� �� ��� �� ��� ��� � �� ��� ���� 20 ���� Unit of measure: mm Screen size: inch
SIM2 Multimedia S.p.a. • Viale Lino Zanussi, 11 • 33170 Pordenone - ITALY Phone +39.434.383.253-256 • Fax +39.434.383260-261 www.sim2.com • e-mail: info@sim2.it SIM2 USA Inc. • 10108 USA Today Way • 33025 Miramar FL - USA Phone +1.954.4422999 • Fax +1.954.4422998 www.sim2usa.com • e-mail: sales@sim2usa.com SIM2 Deutschland GmbH • Gewerbepark, 17 D-35606 Solms Phone 0800.800.7462 • Fax 0800.900.7462 www.sim2.com • e-mail: info.de@sim2.it SIM2 UK LTD • Steinway House Worth Farm, Little Horsted Nr.
