Installation manual

C3X LINK
24
25
(loss of position within the equidistant vertical bands or instability
and lack of sharpness on the narrow vertical lines) it may help
to prompt the system to repeat the input signal analysis and
determination of the best parameters by calling the automatic
adjustment procedure with the A key on the remote control or
the AUTO key on the keypad.
If the automatic procedure fails to have the required effect,
enter the frequency and phase values manually and ap-
proach the screen sufficiently to observe the effects of the
adjustments.
Table 5
OVERSCAN
Eliminates irregularities around the outer borders of the ima-
ge.
Certain relatively inaccurate sources can produce an image
with more or less pronounced irregularities around the outer
edges; thanks to the overscan function these imperfections
can be moved to outside the projected area. Overscan values
can be between 0 (no overscanning) and 32 (maximum over-
scanning). The resulting image always maintains the selected
aspect irrespective of the selected overscan value.
Y/C DELAY
In the case of Video and S-Video signals, it may be necessary
to correct horizontal colour misalignment within the projected
image. For a given video standard (e.g. PAL or NTSC) the stored
value does not normally require further fine-tuning, unless the
source or connection cable has changed.
SETUP
The setup menu contains less frequently used adjustments
that may be required during installation (such as the display
of Test Patterns).
ORIENTATION
Select the option that best describes the installation i.e. desktop
front, ceiling front, desktop rear and ceiling rear.
^!#).
&53%

4
!(
6^
#,!33,!3%202/$5#4
%3#
-%.5
3/52#%
#!54)/.

FORCONTI
NUED

PROTECTIO
NAGAINSTRI
SKOF
FIREREPLA
CE

ONLYWITH
SAMETYP
EANDRATING
FUSE
!44%.4)/.
POURNE
PASCOMPRO
METTRELAPRO
TECTIONCON
TRELESRESQU
ES
DINCNDIER
EMPLACERPA
RUNFUSI
BLEDEMEMETYPEETD
EMEMSCARA
CTERISTIQU
E
!4%8!3).3
425-%.434
%#(./,/'9




0
I
Fig.23
HORIZONTAL / VERTICAL KEYSTONE
To obtain maximum quality of the projected image, we re-
commend the installation of the projector on a level platform
parallel and central to the screen. Adjust the feet undernea-
th the projector to obtain a level position, lining up the base
of the projected image to the base of the projection screen
(Fig.24).
53"1&;*0

^!#).
&53%

4
!(
6^
#,!33,!3%202/$5#4
%3#
-%.5
3/52#%
#!54)/.

FORCONTI
NUED

PROTECTIO
NAGAINSTRI
SKOF
FIREREPLA
CE

ONLYWITH
SAMETYP
EANDRATING
FUSE
!44%.4)/.
POURNE
PASCOMPRO
METTRELAPRO
TECTIONCON
TRELESRESQU
ES
DINCNDIER
EMPLACERPA
RUNFUSI
BLEDEMEM
ETYPEETD
EMEMSCARA
CTERISTIQU
E
!4%8!3).3
425-%.434
%#(./,/'9




0
I
Fig.24
Position
Aspect
Video S-Video
RGBS
YCrCb
RGB Grafico
RGBS 15kHz
YCrCb 15kHz
!DJUSTMENTS
)NPUTS
Frequency
-
-
Phase
Gamma Correction
Colour T
emperature
Y/C Delay
-
-
-
-
-
-
-
-
Overscan
-
DVI-D
HDMI™
ON-SCREEN MENU