SIM2 Multimedia Nero 3D-1, Nero 3D-2, Nero 3D HB User Guide
Contents 3 Important information Safety 3D content Environment Notice 7 Chapter 1: Introduction About This User Guide Key Features and Benefits System Components Optional Accessories 9 Chapter 2: Overview Remote Control Projector Keypad Connections 3D IR Emitter 3D Glasses 13 Chapter 3: Installation Location Mounting Connections Switching On and Off 19 Chapter 4: Operation Viewing 3D Content 3D Menu Input Menu Main Menu Picture Image Setup Menu Memories Info Quick Menus Messages 36 38 40 41 Chapt
Important information Safety To reduce the risk of electrocution, disconnect the power cord on the rear panel before removing the top cover of the projector. For technical service refer to trained personnel authorized by the manufacturer. If the lamp suddenly explodes with a loud bang, turn off the projector immediately and air the room thoroughly. Do not attempt to restart the projector and do attempt to replace the bulb: contact your local service center.
with a flat head screwdriver and replace the fuse. Fit the replacement fuse. Use only type T 10 A L H fuses for the projector. Be careful with cables Make sure cables are routed so that people are not impeded or become a trip hazard. Keep all cables away from children. Install the projector as close to the wall socket as possible.
3D content Discomfort (such as eye strain, headaches, motion sickness, nausea, dizziness, disorientation) may be experienced while watching 3D content. In this case, stop watching and consult a doctor if symptoms are severe. Consult a doctor before allowing young children (especially those under six years old) to watch 3D content as their visual system is still under development.
Product disposal The lamp inside this projector contains mercury and may be subject to special disposal or recycle regulations. Dispose or recycle in accordance with local laws. For more information contact the Electronic Industries Alliance at www.eiae.org or check www.lamprecycle.org Notice The appliance has been subjected to exhaustive operating tests by SIM2 to guarantee the highest quality. The projector bulb life should thus initially be around 30-60 hours.
1 Introduction The Nero 3D-1/3D-2/3D HB are high-end compact 1-chip DLP 3D single unit projectors that utilize SIM2’s state-of-the-art optical technologies to produce images with exceptional black level and contrast performance. The Nero 3D-1/3D-2/3D HB are able to emulate the best 3D cinema projection systems, in terms of color fidelity, definition and depth of image. These are all conveyed accurately, as is the fluid motion of fast-action movies and sports.
System Components Your Nero 3D DLP projector ships with the following items: • 1 x backlit remote control unit (with four AAA/LR03 batteries) • 3 x AC power cords (US, EU and UK), 2 m (6.6 ft.) long • 3 x jacks for 12 V output connectors • 1 x 4.0-millimeter Hex wrench (for lens shift adjustment) • 1 x User guide (this document) • 1 x CD with Live Color Calibration software (for Windows-based computers) If any items are missing or damaged, contact your SIM2 Authorized Dealer as soon as possible.
2 Overview Remote Control ❶ ❷ ❸ ❹ ❻ ❺ ❶ Turn backlight on for about 5 seconds ❷ turns the projector off ❸ 1-9 select inputs and turn the projector on ❹ 0 enters OSD Input menu and turns the projector on ❺ ● OK enters submenus, confirms actions ❻ ESC exits OSD ❼ ◂ ❽ MENU enter OSD Main menu and select + / - the desired section, each press of the key selects the next tab in the menu ❾ II ❼ ❽ ❿ ❾ ⓫ ⓭ ⓰ ⓯ ⓬ ⓮ ▴ ▾ select menu items, adjust settings or ▸ cycle through the test pat
◦ Memories ◦ 3D Controls (3D Mode and Input Formats) Operation The Nero 3D projector has two IR receivers, one on the front and one on the back of the unit. The operative range of the remote control is approximately 10 m (33 ft.). Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver you are pointing to. You can point the remote control towards the screen, as the IR beam is reflected by the screen towards front IR receiver of the projector.
Connections ❶ ❷ ❼ Inputs ❶ HDMI 1 HDMI 2 ❸ ❹ ❺ ❻ ❽ Accept both HDMI and DVI digital video inputs. ❷ Components/RGB-HV Four RCA connectors. They accept both standard and high-definition component (YPrPb) and RGB-HV signals. Also used as RGB input for SCART RGBS signals. Control/ Service Outputs ❸ Video One RCA connector. Accepts composite video signals. Also used as composite sync input for SCART RGBS signals. ❹ Graphics RGB One D-Sub 15-pin female connector.
3D IR Emitter The 3D infrared emitter is designed to be placed near the projector and aimed at the screen. It receives the 3D sync signal from the projector and emits infrared pulses that bounce off the screen and the walls to reach the 3D glasses infrared receiver. Note: The emitter emits sync pulses only when the projector displays 3D content. 3D Glasses When displaying 3D content, the projector alternately displays one image for the left eye and one image for the right eye in rapid succession.
3 Installation This section provides instructions for the installation of the Nero 3D projector. Important: Installation procedures should be performed by a qualified AV system specialist. Location When installing the Nero 3D projector, take the following considerations into account.
Ceiling Mounting Invert the projector and suspend it from the ceiling using a specific bracket. • To fit the bracket unscrew and remove the 3 rubber feet • Attach bracket by using 3 x M6 screws not exceeding 15 mm in length For ceiling mounting use only SIM2-approved ceiling brackets and adhere to the installation instructions and safety guidelines provided with the bracket. Do not over-tighten the screws.
If it is not possible to position the projector perpendicular to the projection screen (so that the lens center and screen center are aligned with each other) you can use the mechanical lens control at the top of the projector to shift the projected image vertically: • insert the provided hex wrench into the vertical lens shift adjuster • turn the wrench to shift the lens in the desired direction The Nero 3D provides up to 50% of vertical lens shift up. For example, with a 16:9 150 in.
• • • throughout the entire signal path ◦ highest available resolution, because video sources can deliver full resolution content via HDMI only ◦ availability of 3D content, because most 3D compatible sources deliver 3D content from HDMI only ◦ optimization of several image parameters (2D/3D content, color space, aspect, signal range, over scan), thanks to auxiliary information (AVI infoframe) sent by the source device together with the signal.
Note: RS-232 communications are limited to 15 m (50 ft.), whereas USB are limited to 5 m (16 ft.). Triggers Some Home Theater devices can be controlled through a 12 V signal. The projector can output three 12 V (100 mA max) signals: • TRIG1 for motorized screens control • TRIG2 and TRIG3 are for motorized screen masks and anamorphic lens motors control.
Switching On and Off Switching On 1. Turn on the main power switch on the right hand side of the projector. The projector enters the low power Standby status. The indicator light on the left hand side of the projector turns red and the status display next to it shows . . 2. Press any of the numeric keys (0-9) on the remote control or the I/O button on the projector keypad to switch on the projector. 3. The indicator light turns green and red and the status display shows 88 for a while. 4.
4 Operation Viewing 3D Content 3D stereo visualization offers clear and sharp 3D images thanks to 3 chip DLP Imaging technology. This technique achieves channel separation using active shutter glasses. • Active shutter glasses turn on and off in rapid succession and stop light reaching your eyes. The glasses are synced using a IR emitter connected to the projector.
• • Switch on your 3D glasses. Refer to the instructions supplied with the glasses to ensure correct operation. The projector will automatically detect the 3D signal and you will be prompted to wear your glasses via the OSD. To Watch 3D Content via Satellite, Cable and Games Console • Switch on the Nero 3D and all other relevant products such as Satellite receiver and AV receiver and ensure the correct inputs have been selected. • Select the appropriate 3D channel.
• 2D display mode for normal 2D material. 3D Input Format adjustment is unavailable. PureMotion adjustment is available. 3D Input Format The Nero 3D checks AVI infoframe data and input signal resolution in order to determine the appropriate 3D format. When automatic detection of 3D format is not possible, choose one of the following options: • (S-S) Side by Side Left and right halves of the image are separated, rescaled and displayed.
Table 4.1 Signal 3D Format 1920 x 1080p @ 23.98/24 Hz Frame Packing Side by Side Top and Bottom 1920 x 1080p @ 25 Hz Side by Side Top and Bottom 1920 x 1080p @ 29.97/30 Hz Side by Side Top and Bottom 1920 x 1080p @ 50 Hz Side by Side Top and Bottom 1920 x 1080p @ 59.94/60 Hz Side by Side Top and Bottom 1920 x 1080i @ 50 Hz Side by Side Top and Bottom 1920 x 1080i @ 59.94/60 Hz Side by Side Top and Bottom 1280 x 720p @ 50 Hz Frame Packing Side by Side Top and Bottom 1280 x 720p @ 59.
To enter the Input menu press: Key 0 on the remote control or Source on the projector keypad. • To select an input press the corresponding number on the remote control, or: 1. ▴ or ▾ on the remote control or on the keypad to highlight the input 2.
Picture This menu section provides access to common image quality adjustments. Adjustments not available for a given input are not displayed in the menu (See Table 4.3 for details). Table 4.3 Video Brightness Contrast Color Tint Sharpness Filter Sharpness Mode Cinema Mode Video Mode Noise Reduction Mode DynamicBlack PureMotion Notes: 1. NTSC only 2. YPrPb Interlaced only 3. YPrPb only 4. Nero 3D-2 and 3D HB only 5.
white objects surrounded by light objects with lower level lighting, and try to ensure that all the objects can be separately identified. Color This control (also called Saturation) increases or decreases the picture color intensity. When set to zero, color images are shown in black and white. Increase the value until the colors appear natural: suitable references include skin tones and the green in grass in landscape shots. Tint This adjustment controls the purity of colors.
Note: When viewing 3D contents, the PureMotion3D mode is automatically activated. DynamicBlack (Nero 3D-2/ 3D HB) This adjustement is available only on the Nero 3D-2 and Nero 3D HB. DynamicBlack improves the level of black and increases the depth and the detail of the image especially in parts with low and medium brightness. It regulates light based on the informative content of the image being projected. Available settings are Off, Video and Movie.
Normal projects the image occupying the full height of the screen while maintaining the aspect ratio of the input signal. When the input signal aspect ratio is 4:3, black vertical bands are displayed on the right and left of the picture. • Anamorphic correctly displays a 16:9 image with over scan. • Letterbox displays a 4:3 letterbox image (source signal with black bands above and below the picture) in such a way that it fills the 16:9 screen and maintains the correct aspect.
Standard the white point associated to the value selected in column 1 High, Medium, Low default white balance levels Native the projector native white point D75, D65, D50 the C standard CIE illuminants User a white point that can be adjusted according to your personal preferences as follows: ▪ press the number 3 on the remote control to activate the User column ▪ position the white point within the CIE chromaticity diagram Note: To accurately set the Primaries and White Point you will need access to special
Frequency/Phase These adjustments, available for progressive signals and for signals from a PC, ensure correspondence between the number of pixels making up the signal and the number of pixels that make up the projected image.
Variable Iris (Nero 3D-2/3D HB) This adjustement is available only on the Nero 3D-2 and Nero 3D HB. Controls the iris in the the optical engine. Larger values increase brightness and smaller values increase contrast in the projected image. RGBS Sync This setting indicates where the sync relative to the RGB signal is supplied. Choose: • HV when the HV connector is used for the RBGS sync signal • Video when the RGB sync signal originates from a SCART outlet (via the SCART/R-G-B-sync conversion cable).
Language Selects the desired OSD language. The Nero 3D can display the menus in English, Italian, French, German, Spanish, Swedish, Portuguese, Russian and Simplified Chinese. Source List Allows customization of the Input list. To change the status of an input: 1. highlight the input 2. use the ◂ and ▸ keys to Enable or Disable the input. Disabled inputs are not shown in the input selection menu and cannot be selected via keys 1-5 of the remote control.
Help Menu When enabled, the Help bar (providing tips for menu navigation) is displayed at the bottom of the main menu. OSD Background Selects the background of the OSD (Clear or Solid). OSD Position Changes the location for the display of the Main Menu OSD. To select one of the nine preset positions: • press 1-9 on the remote control To create a custom position: 1. select the preset that is closest to the desired position 2.
Table 4.5 Settings Video RGB/YPrPb Graphics RGB ● ● ● ● ● Brightness ● Contrast ● Color ● Sharpness ● Sharpness Mode Filter ● Cinema Mode ● ● Noise Reduction ● ● DynamicBlack ●2 ●2 PureMotion ● ● Aspect ● ● Color Primaries ● ● Color White ● ● Gamma ● ● Lamp Power ● ● Variable Iris ●2 ●2 3D Input Format Notes: 1. YPrPb only 2. Nero 3D-2 and Nero 3D HB only 3. See Table 4.
The confirmation message “Memory (1-6) recalled” is displayed. The last memory you have recalled becomes the active memory for the current input (the memory that is automatically recalled each time that input is selected). If this behavior is not desired: 1. recall the desired memory as described above 2. select Auto (the line numbered 0 in the Memory menu) and press ▸ Note: If you are using a custom control system, discrete codes for recalling Memories are available.
Sharpness, Filter and Noise Reduction will appear on after the other in the lower part of the screen by pressing ▴ or ▾. Messages The following messages may appear on your screen: • No signal. The projector does not recognize any signal applied to the selected input. In this case: ◦ make sure the selected input is connected to a video or graphic signal and that this source is functioning correctly. ◦ check the condition of the cables used to connect the system to the various sources.
5 Troubleshooting The projector does not turn on • Make sure the main power switch (at the rear of the projector) is in the On position. • Ensure the projector is connected to an electrical outlet and the outlet is working. • Check the fuse located near the AC receptacle on the right hand side of the projector. • Replace the fuse with one of the same type and rating (T 10 A L H 250 V). • If the fuse blows repeatedly, contact an authorized technical center.
3D content is displayed as two near-identical images • If they are next to each other, press the 3D key on the remote control and then choose Side by Side 3D Input Format. • If they are one above the other, press the 3D key on the remote control and then choose Top and Bottom 3D Input Format. 3D image lacks depth • Press the 3D key on the remote control, highlight the 3D Left/Right setting and then choose the value (either Normal or Swapped) that restores the correct sense of depth in the image.
6 Specifications Projection Type Digital Light Processing (DLP), 1-chip DLP Type: 0.95 in., 1920 x 1080 Optical Engine Die cast, based on SIM2 patented ALPHAPATH Projection Lens High-quality glass Throw ratio: T1: 1.37-1.66:1 T2: 1.75-2.48:1 T3: 2.54-3.
Video Standards Composite: NTSC 3.58/4.43, PAL B/G/H/I/M/N/60, SECAM (automatically selected) Components/RGBHV: 480i, 576i, 480p, 576p, 1080i 50/60, 720p 50/60, 1080p 24/25/30/50/60, VGA, SVGA, XGA, SXGA, UXGA HDMI: 480i, 576i, 480p, 576p, 1080i 50/60, 720p 50/60, 1080p 24/25/30/50/60, VGA, SVGA, XGA 3D Formats All HDMI 1.4a mandatory formats All DVB formats Others (refer to Table 4.
7 Projection Distances 1.78:1 (16:9) Screen Projection Distance Screen T1 (1.37-1.66:1) T2 (1.75-2.48:1) T3 (2.54-3.90:1) Vertical Offset (m) Diagonal Size (in.) Width (m) Height (m) Min (m) Max (m) Min (m) Max (m) Min (m) Max (m) 100 2.21 1.25 3.03 3.73 3.92 5.22 5.76 8.63 0.62 120 2.66 1.49 3.65 4.48 4.72 6.38 6.91 10.36 0.75 150 3.32 1.87 4.58 5.62 5.93 8.24 8.63 12.95 0.93 180 3.98 2.24 5.52 6.76 7.13 9.96 10.36 15.54 1.12 200 4.43 2.49 6.14 7.
8 Dimensions Nero 3D dimensions in millimeters and (inches).
SIM2 Multimedia S.p.a. Viale Lino Zanussi, 11 33170 Pordenone – ITALY Phone: + 39 434 383256 Fax: +39 434 383260 Email: info@sim2.it www.sim2.com SIM2 USA 10108 USA Today Way Miramar, FL 33025 USA Phone: + 1 954 4422999 Fax: + 1 954 4422998 Email: sales@sim2usa.com www.sim2usa.com SIM2 BRIONVEGA Co., Ltd Room 303-304, No. 244 Liaoning Road Shanghai 200080 – CN Phone/Fax: 86 1 62881991 Email: InfoCHINA@sim2.com SIM2 UK Steinway House Worth Farm Little Horsted Nr.
