User and Installation Manual The home theater projector cod.46.0495.
BACK LIGHT Turn on the back light STAND-BY LIGHT Switches off to stand-by. 0-9 Keys Switch on from stand-by and allow direct source selection. SOURCE Displays the Source Selection menu. ESCAPE Deactivates th e On Screen Display. Activates test patterns for zoom and focus adjustment Up/Down/Left/Right Arrow keys Navigate through and make adjustments to the On Screen menus. Arrow Up/Down activate Quick menus. MENU Activates the On Screen Display menus. Navigates menu pages.
1 INTRODUCTION Congratulations and thank you for choosing a HT305 projector, a SIM2 Multimedia SpA product (Fig. 1). ttre comprome d'incende ne pas type N: pour les resque de meme ATTENTIO contre fusible ique par un against la protection caracterist protection remplacer mems et de : for continued CAUTION fire, replace type risk of same with fuse.
A sophisticated proprietary optical system, coupled with a hight performance zoom lens ensures hight contrast images, superior uniformity and edge-to-edge definition. A new 6-segment colour wheel dramatically reduces the so called “rainbow effect” and gives a better contrast, better colorimetry and a lower black level to the image.
1 3 2 5 8 7 4 6 12 11 13 17 R/C 14 ZOO M RAP 4 G H R ICS GB 15 CON TRO L (R S 23 r G/Y B/C 2 1 3 I DM 5 H 9 AU OUT b 2) HV 16 10 ettre mprom e pas co e d'incende ur ne qu N: po e les res meme typ NTIO ntr ATTEtection co fusible de st e la pro cer par un teristiqu n again rac tectio remplamems ca pro ed ntinu et de for co e ION: CAUT fire, replac type risk of h same wit only ing fuse.
2 IMPORTANT SAFETY INSTRUCTIONS ATTENTION: To reduce the risk of electric shock, disconnect the power supply cable on the rear panel before removing the top cover of the projector. Refer to trained, authorised personnel for technical assistance. This symbol indicates the possible electric shock hazard associated with uninsulated live components in the interior of the unit. This symbol indicates the presence of important instructions regarding use and maintenance of the product.
Please follow carefully the warnings listed below, to ensure safe and long term performance of your projector. ettre mprom e pas coue d'incend pe ur ne N: po re les resq meme ty NTIO nt de ATTE ection co fusible nst la protacer par uncteristique n agai ra ectio remplmems ca d prot ue in de nt et : for co N O TI CAU type same with only • Connect the projector to a power supply with a nominal voltage within the following values: 100-240 Vac, 50/60 Hz, earthed (Fig. 3).
• The projector must be positioned on a stable, suitable platform or be installed using a bracket for fixed ceiling or wall installation. Do not rest the projector on the side panels or on the rear panel when in operation. refully follow the installation and safety instructions provided with the bracket’s literature. • Please remove batteries from the remote control if not in use for a long period of time. • Take care to position cables safely, especially in dark places, in order to avoid a trip hazard.
4 INSTALLATION ZO O M Position the projector on a stable, suitable platform or utilise the optional bracket for a fixed ceiling or wall installation. CAUTION: In the case of ceiling or wall mounting using a suspension bracket, follow the instructions carefully and comply with the safety standards you will find in the box together with the bracket.
KEYSTONE 20% ttre comprome d'incende ne pas type N: pour les resque de meme ATTENTIO contre fusible tique par un against la protection caracteris protection remplacer mems et de : for continued CAUTION fire, replace type risk of same with fuse. only and rating R/Cr ZOOM 4 GRAPH ICS RGB G/Y 5 DIGITA 3 AUDIO OUT L INPUT B/Cb 2 CONTR 1 OL (RS 232) HV Fig.
Avoid light shining directly on the screen during projection as this will reduce contrast and black level detail on the projected image. For the true cinema experience best results are achieved with little or no ambient light. Furniture and other objects with reflecting surfaces, as well as light coloured walls should be avoided, as they are likely to interfere with the screen’s characteristics.
Switching off and returning to stand-by (red and green LEDs flashing) and will stop automatically after this period. By remote control: press By keyboard: press key Led indicators The LED indicators, located in the top-rear of the projector, provide information about the state of the projector (see table below). When switching off, the projector goes in to stand-by memorising the input selection at the time of switch-off.
Frequency of between 32-80 kHz and a Vertical frequency of between 48-100 Hz. Computer Resolutions of VGA, SVGA, XGA, SXGA and UXGA can be displayed. Composite video input B/C 2 1 CO OL NTR (RS 232 b ) R HV ZOO RA 4 G M PHIC GB SR C 1 RO ONT L (R S 23 I G/Y B/C 2 st tique n again cteris otectio s cara ed pr mem ntinu et de for co ION: ce CAUT fire, replatype of risk th same . wi only ting fuse and ra UDIO /Cr 3 DM 5 H A OUT b 2) HV CVBS COMPOSITE VIDEO Fig.
care to observe the correspondence with the outputs on the source. The video signals that can be connected to this input can have horizontal scanning frequencies of 15 kHz (standard video resolution), 32 kHz, or higher (progressive scanning video, high definition video). Some sources provide the facility to choose between a progressive signal or an interlaced signal.
R/C RS232 Interface connector It is possible to control the projector through a personal computer. First, load the appropriate projector control software onto your PC, then simply connect this input to a cab l e f r o m y o u r P C ’ s R S 232 s e r i a l p o r t ( F i g . 2 3 ) . ZOO M R 4 G IC APH SR GB 1 CO OL NTR (RS 232 r G/Y B/C 2 d ntinue : for co e ac TION CAU fire, repl type risk of ith same . w only ting fuse and ra 3 I DM 5 H ainst tion ag protec IO AUD OUT b ) HV Fig.
8 REMOTE CONTROL Insert the batteries, taking care to match the polarity, as indicated in the battery recess of the remote (Fig. 24). - + + - + + - The remote control sends commands to the projector via infrared signals. It is possible to control the projector by pointing the remote control at the screen; the sensor at the front of the projector will pick up the reflected infrared commands. (Fig. 25). four 1,5 V AAA type batteries DVI C-SYNC LIGHT ZOOM F1 Fig. 24 Fig.
9 ON SCREEN MENU SOURCE SELECTION by pressing the Ë key. During the short time it takes to find the signal, a box appears showing the signal requested. As soon as the signal is shown in the box additional information is displayed concerning the video standard (for video signals) or resolution (for graphic signals), and format. Fom the SETUP menu it is possible to choose to visualize or not this information, for more details check the “SOURCE INFORMATION” in “MENU” section.
which appear as a superimposed window in which the selection is made with the È/Í keys (Fig. 28). black objects alongside other dark coloured objects. Contrast Use this control to adjust the image’s black level without affecting white areas.To ensure correct adjustment, it may prove useful to display the signal relative to the grey scale, within which the white level and the level immediately below it must be separately identifiable.
In AUTO the deinterlacer recognises if the video signal source is a movie film (obtained from a Telecine device with 3:2 or 2:2 pull-down) and applies a deinterlace algorithm optimised for this type of signal. If the video signal source is not identified as a film, or if you select NO the deinterlacer applies a Motion compensated algorithm optimised for video camera signals. part the filter is activated. This allows you to compare the effect of the filter.
Color Temperature The color temperature adjustment is made by positioning the white point inside CIE cromaticity diagram. The systems allows to choose from 36 predefined white points inside the neutral color area (Fig.29). IMAGE This menu features adjustments relating to picture position, aspect ratio, etc. Aspect This adjustment allows you to change the dimensions and aspect ratio (relationship between width and height) of the displayed image.
Along vertical lines the color temperature is constant but is different from black body curve, which mean if you select point from the high part of the diagram you increase the green componet, while low part of diagram cause an increase of purple component. useful to request the system to repeat the input signal analysis and image positioning, calling the automatic control procedure from the AUTO button on the remote control or keypad.
be moved vertically, up or down, in relation to the centre of the screen; the maximum adjustment being equal to half the height of the image in either direction (Fig. 33). SETUP The setup menu contains less frequently used adjustments that may be required during installation (e.g. On Screen Display language selection or the display of Test Patterns). ORIENTATION Select the option that best describes the installation i.e. desktop front, ceiling front, desktop rear and ceiling rear..
n the initial phase of installation the configurable keys (F1, F2) serve as optical zoom and optical focus (Fig.34). Source list/Edit source name 1 2 3 4 5 POWER ON If active (AUTO) allows to power up the system directly from the power feeder, once the initializing phase is completed. If not active (STAND-BY) once the initializing phase is completed the system remains in a stand-by mode waiting to receive the power on command from the remote control or the key pad.
Once one letter has been inserted, to insert the following one it is necessary to move with the cursor in the next right position with the Ë key of the remote control, repeat this procedure to insert other letters. Use the È key to switch from small case to capital letters and viceversa. Any mistake can be deleted with the Í key once it has been positioned on the wrong letter. Once the text insertion process is finished, it can be confirmed and saved by clicking the MENU+ key.
SAVE A MEMORY To save the current values of the image parameters in Memory 1, use the È and Í keys to move to line ‘1’ and then open the pull-down menu by pressing the Á/Ë key (Fig.39). Then select the option ‘Save current settings’. To confirm that the operation has been completed successfully, the message ‘Current settings saved in Memory 1’ is displayed at the bottom of the screen and the letter ‘S’ appears to the left of the memory name. The same procedure is used to save parameters in Memories 2 and 3.
On entering the ‘Memories’ menu, a copy of the current settings is saved in a temporary menu (labelled with 0 - AUTO). Once one or more memories have been recalled, you can restore the settings that were effective at the moment the Memories menu was accessed by selecting 0 - AUTO. However, this operation must be completed before the ‘Memories’ menu page disappears (30 seconds after the last operation commanded from the remote control or the keypad).
11 TROUBLESHOOTING GUIDE that the aerial system is in good working order. - Should the problem be present with a signal coming from a video-recorder, ensure that the videotape is an Original “first generation” copy and in good condition. - Adjust the VCR’s tracking control for optimum picture performance. Ensure the VCR mode is active in the Picture menu. No power (Green and red LED are OFF) - Check the power switch at the rear: it must be in position I.
Video Image showing colour misalignment on vertical details Remote control does not work - Check the batteries and for correct polarity. - Ensure that the area between the infrared sensor (front of projector) and the remote control is free of obstruction. - Ensure that infrared sensors (front and rear of projector) are not exposed to intense light levels. - Verify compatibility of video/graphic signals with technical specifications of your projector.
A TECHNICAL SPECIFICATIONS OPTICAL HT 305 Projection system: optical engine based on 1 DMD™ DarkChip3™ chip, sealed housing, dusty proof DMD™ panel: resolution 1280x720 pixel Brightness uniformity: 10% above or below the average Contrast ratio: > 3200:1 (full On / full Off) Projection lens: zoom, 12 elements AR multilayer coating, motorized focus and zoom, manual elevation Aperture f#: 2.7 (zoom max) - 3.
ELECTRICAL Input Signals: GENERAL CVBS on RCA/Phono type connector S-VHS on Mini-DIN connector RGBHV on DB15HD connector RGBS / YCrCb on RCA/Phono type connector HDMI™ Supply: from 100 to 240 Vac, -10% +6% tolerance Frequency: from 48 to 62 Hz Horizontal frequency: from 15 to 80 kHz (up to to UXGA format @ 60 Hz) Fuse: Vertical frequency: 48-100 Hz Dimensions of projector: 352 mm x 174 mm x 318 mm (LxHxD) 13”-7/8 x 6”-7/8 x 12”-1/2 (LxHxD) Video standards : automatically selected (PAL B,G,H, I,
102 174 74 352 B DIMENSIONS 318 unit: mm (inches) C PROJECTION DISTANCES H Follow the table below to determine the optimal projection distance “L” between the screen (Fig.40a) and the center of the lens. This will help you to obtain the desired screen size.The manual lens shift adjustments allows the projected image to be moved vertically, up or down, in relation to the centre of the screen (Fig.40b).
Projection distance table HT305 16/9 Screen Screen size width Min projection distance Max projection distance (diagonal) in. 50” 60” 70” 80” 90” 100” 120’ 150” 180” 200” 220” 250” m in. 1,1 44” 1,3 52” 1,6 61” 1,8 70” 2,0 78” 2,2 87” 2,7 105” 3,3 131” 4,0 157” 4,4 174” 4,9 192” 5,5 218” min. L m ft. in.
D On screen menu layout Picture Video • S-Video [NTSC] YCrCb15kHz RGBS 15kHz Brightness Contrast Color Tint Sharpness Filter Cinema Mode Video Type Noise reduction Brightness Contrast Color Sharpness Filter Cinema Mode Video Type Noise reduction Not active Video • S-Video [PAL, SECAM] YCrCb Brightness Contrast Sharpness Sharpness Mode Brightness Contrast Color Tint Sharpness Sharpness Mode Auto Flesh tone correction RGBS RGB Grafico HDMI™ Manual On Off Value Flesh tone correction On Off Imag
Horizontal Vertical Screen control Setup Orientation Keystone Lens Power ON Test patterns Initial settings Zoom Focus Auto Stand-by English Italiano Français Deusch Español Português Menu Language Source list F1/F2 keys Source info OSD background OSD Position OSD Timeout Floor Floor-rear Ceiling Ceiling-rear Horizontal Horizontal Yes No Zoom Focua Magnification Blank Color temperature Gamma correction 1 VIDEO 1 2 S-VIDEO 2 3 COMPONENT / RGBS 3 VIDEO 1 S-VIDEO 2 COMP RGB 3 4 GRAPHICS RGB 4 GRAP
- Confirm + 0 Memories Memories 0 Auto 1 S MEMORY 1 2 S MEMORY 2 3 S MEMORY 3 Save current settings Save initial settings Rename ()?@ 1 Edit memory name ___________ 35 Cancel - Confirm + ABC 2 DEF 3 GHI 4 JKL 5 MNO 6 PQRS 7 TUV 8 WXYZ 9 0
INDEX 1 INTRODUCTION 3 Source selection 17 2 IMPORTANT SAFETY INSTRUCTIONS 6 Main menu 17 3 PACKAGING AND CONTENTS 8 Picture 18 4 INSTALLATION 9 Image 20 5 SWITCHING ON AND OFF THE PROJECTOR 11 Set up 22 Switch on from stand-by 11 Menu 23 Switching off and returning to stand-by 12 Memories 25 12 Info 26 6 CONNECTIONS Composite video input 13 Quick menus 26 S-VIDEO Input 13 Messages 26
SIM2 Multimedia S.p.a. • Viale Lino Zanussi, 11 • 33170 Pordenone - ITALY Phone +39.434.383.253-256 • Fax +39.434.383260-261 www.sim2.com • e-mail: info@sim2.it SIM2 USA Inc. • 10108 USA Today Way • 33025 Miramar FL - USA Phone +1.954.4422999 • Fax +1.954.4422998 www.sim2usa.com • e-mail: sales@sim2usa.com SIM2 Deutschland GmbH • Gewerbepark, 17 D-35606 Solms Phone 0800.800.7462 • Fax 0800.900.7462 www.sim2.com • e-mail: info.de@sim2.it SIM2 UK LTD • Steinway House Worth Farm, Little Horsted Nr.
