HT3000E 460649000 <<< user and installation manual
ht3000e 1 REMOTE CONTROL AND KEYPAD Backlighting Backlights the keys on the remote control LIGHT STAND-BY / ON Sets the panel to stand-by . KEYS 0-9 Select the sources directly. Switches on the panel from Standby. SOURCE Displays the source selection menu. ESCAPE Deactivates the On Screen Display. Up/Down/Left/Right Arrow keys Navigates between the On Screen Display menus and parameter settings. Arrow Up/Down call up the quick menus.
ht3000e 1 INTRODUCTION The HT3000E projector represents the state of the art in image processing combined with the innovative DLP™ sytsem and outstanding optics. Its range of inputs (1 Composite Video input, 1 S-Video input, 1 Components or RGB input, 1 graphic RGB input, 2 HDMI™ inputs) allow it to be connected to a wide range of analogue and digital sources: DVD players, video recorders, satellite and terrestrial receivers, computers, video game consoles, camcorders, etc.
ht3000e FCC STATEMENT CLASS B PRODUCT Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
ht3000e 2 IMPORTANT SAFETY INSTRUCTIONS This symbol indicates the possible electric shock hazard associated with uninsulated live components in the interior of the unit. This symbol indicates the presence of important instructions regarding the use and maintenance of the product. CAUTION To reduce the risk of electric shock, disconnect the power supply cable on the rear panel before removing the top cover of the projector.
ht3000e PROJECTOR 20 5 4 6 13 2 3 1 13 10 7 12 +12 11 V 1 USB 1.1 9 R/Pr CO C/Y NTR OL 3 (RS2 32) B/Pb HV GRA PH 19 ICS S-VI DEO RG B 4 2 S-VI DEO REM OTE AU 1 DIO OU T MEN U 18 HD MI 1 MEN 17 U ES C HD MI SO URC E 2 O I 16 15 14 1 2 3 4 5 6 7 8 9 10 Projection lens. Lens shift knob. Remote control IR sensor on front of unit. Cooling air inlet vents. Adjustable feet. Adjustable carry-handle. Bulb compartment. Fused power socket. Main power switch.
ht3000e • Changing the fuses. Before changing the fuse disconnect the unit from the mains power supply. The fuse compartment is next to the power supply connector (Fig. 3). Remove the fuse holder (2) with a flat head screwdriver and replace the fuse (3). Fit a new spare fuse (4). Use only T 5A H fuses. • Do not allow the unit to overheat. To prevent this, allow a free space of at least 40 cm around the back of the projector. Do not block the ventilation slots.
ht3000e 3 UNPACKING 3 To remove the HT3000E system from its carton follow the diagrams (Fig. 4). 4 Keep the carton for use when transporting or shipping the unit. 2 1 Fig.4 CONTENTS OF PACKAGE - the projector - Remote control - four 1.5V AAA batteries (for remote control) - three power cables (EU, UK, USA) for the projector - the user manual. - Lens shift key If anything is missing, immediately inform your dealer.
ht3000e 4 INSTALLATION Position the projector on a stable, suitable platform or utilise the optional bracket for a fixed ceiling installation. ZOOM FOCUS OM ZO WARNING: If using the ceiling mount bracket, scrupulously observe the safety instructions included with the bracket itself. If using a bracket other than that supplied by SIM2 Multimedia, make sure that the projector is at least 65 mm below the ceiling and that the bracket does not obstruct the air vents (intake and outlet).
ht3000e screen’s axis. Prevent ambient light shining directly on the screen during projection as this will reduce the contrast of the projected image. Furniture and other objects with reflecting surfaces, as well as light coloured walls should be avoided, as they are likely to interfere with the screen’s characteristics. Fig. 9 To activate an electric motorised screen a 12 Volt output is provided at the rear of the projector (Fig. 10).
ht3000e 5 SWITCHING THE PROJECTOR ON AND OFF WARNING: Connect the projector to a power supply with a nominal voltage within the following values: 100-240 V AC, 50/60 Hz. It must be earthed (Fig. 12). Power Switch: Position I: On Position 0: Off HV GR AP S-V HIC SR GB IDE O 4 2 S-V IDE REM O DIO E With the remote control press one of the keys (Fig. 14): - 0 to select the last imput selectet after last switching off. - 1-9 to select the correspondent imput.
ht3000e Switching off and returning to standby With the remote control: press . With the keypad: press . When switching off, the projector goes into stand-by mode and stores the input selection at the time of switch-off. The fans keep running until the lamp cools down (green and Status red leds on), after which they automatically switch off. Do not switch off the projector with the power switch until the fans have stopped running.
ht3000e HT3000E - Connection panel 3 RGB - YPrPb 4 GRAPHICS RGB +12 V USB 1.1 R/P r CO C/Y NTR OL 2 3 (RS 232 ) B/P b S-VIDEO 1 HV GR AP S-V HIC SR GB IDE O 4 2 S-V REM OT E VIDEO IDE O AU 5 HDMI 6 1 DIO OU HDMI T ME N U HD MI 1 5 ESC HD MI 2 6 SO U RCE O I 1 2 3 Television receiver DVD player Television receiver HDTV receiver VCR Videocamera Video game console DVD player VCR 4 computer 5 6 DVD player HDTV receiver Video game console Fig.
ht3000e COMPOSITE VIDEO 1 Fit an RCA connector with a Composite Video (CVBS) signal to this input. The output connector on the external appliance is normally coloured yellow and will often be labelled VIDEO. Other signal and socket formats may be preferable (because they give better image quality), but this type of output socket is still the most commonly used, and nearly all television receivers, video recorders, DVD players and camcorders, etc. use it.
ht3000e Motorised screen outputs RS232 interface connector 12Volt 120 mA CONTROL RS 232 +1 2V +12 V CONTROL USB US B1 .1 R/C r C/Y 3 RS2 32 USB B/C b HV GR AP HIC S-V SR GB O 2 S-V IDE OT The projector is equipped with two outputs (Voltage: 12 Vdc) for motorised projection screen and screen masking systems, used for masking off the projection area to match the projected image aspect ratio (Fig. 17).
ht3000e 9 ON SCREEN MENU All system functions can be operated from the keypad or remote control, with the aid of a complete, user-friendly on screen menu. INPUTS The input selection menu is called by pressing 0 on the remote control or with the keypad SOURCE key. To select an input, scroll through the list with the ▲ e ▼ keys until the required input is highlighted, then press ▶.
ht3000e To access these submenus, press the <, mentre l’uscita ed il ritorno al livello superiore avviene con la pressione dei tasti MENU+/- key. Press ESC on the remote control or keypad to interrupt the menu display or wait for it to disappear automatically after the number of seconds set on the SET-UP page. PICTURE This menu includes all image adjustment settings. Adjustments that are not available for a given input do not appear on the menu. Table 4 summarises the adjustments available for each input.
ht3000e NOISE REDUCTION This adjustment serves to select the noise reduction filter value. In this latter case, simply click on the slider and set the value with the ◀ and ▶ keys on the remote control. IMAGE This menu features adjustments relating to picture position, aspect ratio, magnification etc. Aspect This adjustment allows you to change the dimensions and aspect ratio (relationship between width and height) of the displayed image.
ht3000e sising or attenuating the different grades of brightness (blacks, dark, medium, light grey, whites) in the projected image. The projector has a range of gamma functions which enable you to display any image to the best effect for the type of video source, the ambient lighting and your subjective preferences. There are 4 sets of gamma curves: Standard (ST), Enhanced SIM2 (EN) and Graphics (GR), User.
ht3000e Enhanced set is suitable for watching movies. The Graphics set is suited to displaying synthetic graphics (PC, CAD, PC presentations, etc.). User enables you to define your own curve. You can thus select the coefficient which determines the curve. Values from 1.5 to 2.2 allow you to emphasise the detail of dark images, but reduce overall contrast. Values higher than 2.2 increase overall contrast, but reduce the detail of dark areas.
ht3000e Confirm? KE YS TO NE 20 % No Yes Fig.28 MENUS LANGUAGE It allow to select the languages available for the On Screen Display menus. Fig.26 LAMP POWER To obtain the greatest picture quality, the LAMP POWER parameter setting is used to vary the power with which the lamp is supplied. In this way, besides adjusting the brightness of the images to your projection conditions (size and type of screen, environmental brightness), the lamp will have a longer life.
ht3000e Table 6 DVI-D HDMI™ RGB Grafico YCrCb RGBS RGBS 15kHz YCrCb 15kHz !DJUSTMENTS Video S-Video )NPUTS Position - Aspect Frequency - - - Phase - - - Colour Temperature Gamma Correction Overscan - Y/C Delay - - - Entering text The text entry menu in (Fig.30) makes it quick and easy to enter text.
ht3000e Blank Switches off the video signal and displays a black page. As soon as the key is pressed an OSD indication lasting a few seconds confirms that the function has been activated. Pressing any further keys on the remote control restores the previous conditions. Color Temperature Clicking the key in question again (F1 / F2) enables you to set the colour temperature from High, Medium, Low, NATIVE and User.
ht3000e 232 ) the corresponding drop-down menu (◀ key). Select the line ‘Save initial settings’. To confirm the operation, the message ‘Initial settings saved in Memory 1’ is shown at the bottom of the display and the letter “I” appears to the left of the memory name. HV GR AP S-V HIC SR GB IDE O 4 2 S-V IDE O REM OTE AU 1 DIO OU T ME NU HD MI 1 5 ESC HD MI 2 6 INP UT Rename a memory All Memories can be named.
ht3000e INFO Displays the current status of the projector and information concerning the projected video/graphic signal. This function is displayed on pressing the key on the remote control (or, in the absence of the On Screen Display, the ▶ key on the keypad). QUICK MENUS The quick menus provide access to the main adjustments that affect image quality without calling the main menu.
ht3000e 10 CLEANING AND MAINTENANCE The projector does not require internal adjustment. There are no user serviceable parts inside the projector. To replace the bulb or any other repairs, contact your local service centre. To clean the outer cover of the screen use a soft cloth and moisten slightly if necessary with water and a small amount of neutral soap. Do not rub the rear panel markings. The lens may be cleaned with a very soft, non-abrasive small brush, in order to remove dust particles.
ht3000e Incomplete image along borders (vertical and horizontal) • • • • • Check compatibility of the video or graphic signals with the technical specifications of the system, and specifically, with the specifications of the selected input. Recall the automatic image adjustment function by pressing the key “A” on the remote control or ◀ on the projector’s keypad. Adjust the horizontal and vertical position of the image with the IMAGE / POSITION menu (if available for the input in question).
ht3000e A TECHNICAL SPECIFICATIONS ELECTRONICS GENERAL PROJECTOR SPECIFICATIONS Input signals: • COMPOSITE VIDEO (CVBS) gold plated RCA connectors 1,0 Vpp / 75 Ω, negative synchronisation • 1 S-VIDEO (Y/C) 4-pole mini-DIN connector Y: 1.0 Vpp / 75 Ω, negative synchronisation C: 0.286 Vpp / 75 Ω, [ nominal NTSC burst level] 0.3 Vpp / 75 Ω [nominal PAL, SECAM burst level] • 1 COMPONENTS (Y/Pr/Pb/) - RGBS 1 set of 4 RCA connectors - Component signals Y: 1.
ht3000e B ON SCREEN MENU LAYOUT Video • S-Video [NTSC] Video • S-Video Aspect Color Temperature Gamma Correction Overscan Position Y/C Delay Component Ghaphics Aspect Color Temperature Gamma Correction Overscan Position Frequency Phase Aspect Color Temperature Gamma Correction Gamma Correction Screen Control Horizontal Vertical Screen control ST1 EN1 EN2 EN3 EN4 EN5 HDMI™ DVI SDI GR1 GR2 User 1,5 3,0 y Color Temperature High Medium Low User x= 0,307 y= 0.320 T= 8700K 0,015 x uv= 2.
ht3000e 1 2 3 4 5 6 VIDEO 1 S-VIDEO 2 COMPONENT 3 GRAPHICS RGB/YPrPb 4 HDMI 5 HDMI 6 Zoom Focus Lens shift Auto Stand-by English Italiano Français Deusch Español Português N PyccK Yes VIDEO S-VIDEO COMPONENT GRAPHICS HDMI HDMI Active Name Save current settings Save initial settings Rename Yes No Edit source name ___________ Cancel - Confirm + ()?@ 1 ABC 2 DEF 3 GHI 4 JKL 5 MNO 6 PQRS 7 TUV 8 WXYZ 9 0 ()?@ 1 Edit memory name ___________ Cancel - Confirm + ABC 2 DEF 3 GHI 4 JK
ht3000e C DIMENSIONS 31
ht3000e D PROJECTION DISTANCE 16/9 Screen size (diagonal) Screen width Min projection distance Max projection distance max L max L .in m in. m in. m in.
SIM2 Multimedia S.p.a. • Viale Lino Zanussi, 11 • 33170 Pordenone - ITALY Phone +39.434.383.253-256 • Fax +39.434.383260-261 www.sim2.com • e-mail: info@sim2.it SIM2 USA Inc. • 10108 USA Today Way • 33025 Miramar FL - USA Phone +1.954.4422999 • Fax +1.954.4422998 www.sim2usa.com • e-mail: sales@sim2usa.com SIM2 Deutschland GmbH • Gewerbepark, 17 D-35606 Solms Phone 0800.800.7462 • Fax 0800.900.7462 www.sim2.com • e-mail: info.de@sim2.it SIM2 UK LTD • Steinway House Worth Farm, Little Horsted Nr.
