C3X LINK DLP™ VIDEO PROJECTOR RS-232C CONTROL SPECIFICATIONS Document Revision 1.
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS Table of Contents 1. INTRODUCTION 3 2. CONNECTION 3 3. COMMUNICATION PROTOCOL 4 HEADER PAYLOAD 4 4 4. COMMANDS 5 REMOTE CONTROL KEY CODES O PERATION CODES GET CODES 5 7 12 5. EXAMPLES 14 6. WARNINGS 14 Revision History: Revision Date Software Version 1.1 16 December 2005 2.48.62 CL or higher 1.0 5 December 2005 2.48.60 CL or higher 2 Description of Change Added ON command. Command 0 is now different from command ON. Initial version.
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS 1. Introduction This document describes the communication and data formats used to control SIM2 C3X LINK projector via RS-232C port. 2. Connection Switch off the Personal Computer the Projector before connecting RS 232C cable. Use a standard serial cable with 9 pin female to the Personal Computer and 9 pin male to the Projector: pin 2 connects to pin2, pin 3 to pin 3 and pin 5 to pin 5. SIM2 C3X LINK RS-232C Port is described as follows.
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS 3. Communication Protocol The communication protocol is packet oriented. Packets consists of Header and Payload. There are two types of packets: Event and Operation. The packet header size is fixed (7 bytes), while the packet payload type and content varies based on the type of packet: Event payload size is 6 bytes, while Operation payload size is 25 bytes.
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS 4. Commands Remote Control Key Codes The following commands send simulated Remote Control input to SIM2 C3X LINK projector.
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS ASPECT USER 1 BE EF 02 06 00 51 F5 88 01 00 00 00 00 ASPECT USER 2 BE EF 02 06 00 80 F4 89 01 00 00 00 00 ASPECT USER 3 BE EF 02 06 00 B3 F4 8A 01 00 00 00 00 VCR BE EF 02 06 00 9B E3 62 01 00 00 00 00 Direct access codes Zoom BE EF 02 06 00 94 E6 5D 01 00 00 00 00 Focus BE EF 02 06 00 76 E7 5F 01 00 00 00 00 Goto Brightness BE EF 02 06 00 C7 E1 7E 01 00 00 00 00 Goto Contrast BE EF 02 06 00 16 E0 7F 01 00 00 00 00 Goto Color BE EF 02 06 00 19 F
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS Operation Codes The following codes provide direct access to SIM2 C3X LINK User Interface operations not accessible via a single Remote Control command.
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS SET 04 SET 05 SET 06 SET 07 SET 08 SET 09 SET 10 SET 11 SET 12 SET 13 SET 14 SET 15 SET 16 SET 17 COLOR TEMPERATURE SET 18 SET 19 SET 20 SET 21 SET 22 SET 23 SET 24 SET 25 SET 26 SET 27 SET 28 SET 29 SET 30 SET 31 SET 32 BE 03 BE 04 BE 05 BE 06 BE 07 BE 08 BE 09 BE 0A BE 0B BE 0C BE 0D BE 0E BE 0F BE 10 BE 11 BE 12 BE 13 BE 14 BE 15 BE 16 BE 17 BE 18 BE 19 BE 1A BE 1B BE 1C BE 1D BE 1E BE 1F EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS SET 33 COLOR TEMPERATURE SET 34 SET 35 SET 36 SET ST1 SET EN1 SET EN2 SET EN3 GAMMA SET EN4 SET EN5 SET GR1 SET GR2 SET USER INCREMENT FREQUENCY DECREMENT INCREMENT PHASE DECREMENT INCREMENT Y/C DELAY DECREMENT INCREMENT MAGNIFICATION DECREMENT INCREMENT PAN HORIZONTAL DECREMENT INCREMENT PAN VERTICAL DECREMENT INCREMENT KEYSTONE VERTICAL DECREMENT KEYSTONE HORIZONTAL INCREMENT DECREMENT BE 20 BE 21 BE 22 BE 23 BE 0B BE 0D BE 0E BE 06 BE 07 BE 09 BE 0A BE
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS BE C8 BE D2 BE DC BE E6 BE F0 BE FA BE 00 BE 01 BE 02 BE 03 BE 04 BE 05 BE 00 BE 00 BE 00 BE 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 19 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS SET YCrCb AutoSync INPUT 7 (COMP RGB 3) / SIGNAL TYPE INPUT 8 (COMP RGB 4) / SIGNAL TYPE BE 16 BE SET YCrCb 15kHz 0A BE SET YCrCb 32kHz 12 BE SET RGB AutoSync 1A BE SET RGB 15kHz 06 BE SET RGB 32kHz 0E BE SET YCrCb AutoSync 17 BE SET YCrCb 15kHz 0B BE SET YCrCb 32kHz 13 BE SET RGB AutoSync 1B BE SET RGB 15kHz 07 BE SET RGB 32kHz 0F EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 EF 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 03 00 0
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS 21 22 23 24 25 26 27 28 29 30 31 32 00 00 00 00 00 00 00 00 00 00 00 00 Get Codes Get Commands may be used to get the current value of projector parameters. The response to a correct Get Command consists of 33 byte packet, where Byte Number 11 contains the Validation Code (01) and bytes Number 17 and Number 18 the requested value (the least-significant byte of the value being sent first).
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS (1) Returned value is indeterminate when the unit is in No Signal state. Returned value may be different from the value displayed on the OSD, as in the latter, the values have been normalized to the 0-100 range. (2) Returned value is valid only when Video, S-Video, RGBS 15 kHz, YPrPb 15 kHz or YPrPb 32 kHz signals are displayed. Returned value is indeterminate when other signals are displayed and when the unit is in No Signal state.
SIM2 C3X LINK RS-232C CONTROL SPECIFICATIONS 5. Examples 1. Send the simulated "SWITCH ON FROM STAND-BY" Remote Control keycode. Remote Control allows Switching on from Stand-by via the key "0". Send the code relative to key "0": BEEF020600A7F79E0100000000. The projector switches on and the last source memorised prior to switch off is automatically selected. The projector returns the response code: 06 (Acknowledged with no error). 2. Send the simulated "MENU RIGHT" Remote Control keycode.
