DOMINO 20H DOMINO 30H DLP™ VIDEO PROJECTOR RS-232C CONTROL SPECIFICATIONS Document Revision 1.
SIM2 DOMINO 20H / DOMINO 30H RS-232C CONTROL SPECIFICATIONS Table of Contents 1. INTRODUCTION 3 2. CONNECTION 3 3. COMMUNICATION PROTOCOL 4 HEADER PAYLOAD 4 4 4. COMMANDS 5 REMOTE CONTROL KEYCODES OPERATION CODES 5 7 5. EXAMPLES 9 6. WARNINGS 10 Revision History: Revision Date Software Version Description of Change 1.1 1.0 20 July 2004 20 April 2004 2.36.09 F or higher 2.33.00 F or higher Auto Sync on Inputs 5/6/7/8 added. Initial version.
SIM2 DOMINO 20H / DOMINO 30H RS-232C CONTROL SPECIFICATIONS 1. Introduction This document describes the communication and data formats used to control SIM2 DOMINO 20H / DOMINO 30H projectors via RS-232C port. 2. Connection Switch off your Personal Computer and Projector before connecting RS 232C cable. Use a standard serial cable with 9 pin female to the Personal Computer and 9 pin male to the Projector: pin 2 connects to pin2, pin 3 to pin 3 and pin 5 to pin 5.
SIM2 DOMINO 20H / DOMINO 30H RS-232C CONTROL SPECIFICATIONS 3. Communication Protocol The communication protocol is packet oriented. Packets consists of Header and Payload. There are two types of packets: Event and Operation. The packet header size is fixed (7 bytes), while the packet payload type and content varies based on the type of packet: Event payload size is 6 bytes, while Operation payload size is 25 bytes.
SIM2 DOMINO 20H / DOMINO 30H RS-232C CONTROL SPECIFICATIONS 4. Commands Remote Control Keycodes The following commands send simulated Remote Control input to SIM2 DOMINO 20H / DOMINO 30H projectors.
SIM2 DOMINO 20H / DOMINO 30H RS-232C CONTROL SPECIFICATIONS Direct access codes Goto Brightness BE EF 02 06 00 C7 E1 7E 01 00 00 00 00 Goto Contrast BE EF 02 06 00 16 E0 7F 01 00 00 00 00 Goto Color BE EF 02 06 00 19 F4 80 01 00 00 00 00 Goto Tint BE EF 02 06 00 C8 F5 81 01 00 00 00 00 (1) When the unit is in Stand-by state, this command switches on the unit and the last source memorised prior to switch off is automatically selected.
SIM2 DOMINO 20H / DOMINO 30H RS-232C CONTROL SPECIFICATIONS Operation Codes The following codes provide direct access to SIM2 DOMINO 20H / DOMINO 30H User Interface operations not accessible via a single Remote Control command.
SIM2 DOMINO 20H / DOMINO 30H RS-232C CONTROL SPECIFICATIONS COLOR TEMP USER/ GAIN RED COLOR TEMP USER/ GAIN GREEN COLOR TEMP USER/ GAIN BLUE COLOR TEMP USER/ OFFSET RED COLOR TEMP USER/ OFFSET GREEN COLOR TEMP USER/ OFFSET BLUE INCREMENT DECREMENT INCREMENT DECREMENT INCREMENT DECREMENT INCREMENT DECREMENT INCREMENT DECREMENT INCREMENT DECREMENT SET FILM GAMMA SET VIDEO SET GRAPHICS INCREMENT FREQUENCY DECREMENT INCREMENT PHASE DECREMENT INCREMENT Y/C DELAY DECREMENT INCREMENT MAGNIFICATION DECREM
SIM2 DOMINO 20H / DOMINO 30H RS-232C CONTROL SPECIFICATIONS KEYSTONE HORIZONTAL INCREMENT DECREMENT SET ENGLISH SET ITALIANO SET FRANCAIS LANGUAGE SET DEUTSCH SET ESPANOL SET PORTUGUES OSD POSITION HORIZONTAL OSD POSITION VERTICAL INCREMENT DECREMENT INCREMENT DECREMENT SET YCrCb AutoSync SET YCrCb 15kHz INPUT 3 (COMP.
SIM2 DOMINO 20H / DOMINO 30H RS-232C CONTROL SPECIFICATIONS 3. Send the "SET ASPECT ANAMORPHIC" Operation Code. Send the packet: BEEF0206009DF5840100000000. The Aspect Ratio changes to Anamorphic. The projector returns the response code: 06 (Acknowledged with no error). 4. Select "INPUT 3 (COMP. RGB) WITH YcrCb 15kHz SIGNAL" Send the packet: BEEF0319005B0C01820800000000000008000000000000000000000000000000 Wait for the return code and add an additional delay of 40 ms.
