STRIDER ESSENTIAL SERIES Power for everything you need SST-ST70F-ESB SST-ST60F-ESB High efficiency with 80 PLUS Bronze certification 24/7 continuous power output with 40℃ operating temperature Class-leading single +12V rail Multiple protection circuitry Silent running 120mm fan with 18dBA PCI-E 8pin and PCI-E 6pin connectors support ATX 12V 2.
SPECIFICATION SilverStone Strider Essential ST70F-ESB ST60F-ESB ATX12V 2.3 Switching Power Supply With Active PFC 80Plus Bronze PS/2 1.General 1.1Scope This specification defines the performance characteristics of a single phase 700,600 watts, 5 output power supply. This specification also defines worldwide safety and electromagnetic compatibility requirements for the power supply which is intended for use in computer products. 2.Input Characteristics 01 2.
STRIDER ESSENTIAL SERIES * The power supply must operate at above frequency with 103.5 - 253VACrms input voltage range. 2.3 Max. Input AC Current Max. Input Current ------------------------10A Measuring Range -----------------------103.5 - 253 Vrms 2.4 Inrush Current The power supply must meet inrush requirements for any rated AC voltage, during turn on at any phase of AC voltage, during a single cycle AC dropout condition, during repetitive ON/OFF cycling of AC, and over the specified temperature range.
NOTE: Noise test should be measured with 20 MHz bandwidth frequency oscilloscope. The output terminal shall add a tantalum capacitor of 10uF in parallel with a ceramic capacitor of 0.1uF. SST-ST60F-ESB: Output Load Range Voltage MIN MAX 1. +5V 0.2A 22.0A ±5% 50mV 2. +3.3V 0.1A 22.0A ±5% 50mV 3. +12V 0.6A 45.0A ±5% 120mV 4. -12V 0.0A 0.3A ±10% 120mV 5. +5Vs 0.0A 2.5A ±5% 50mV Peak 3.5A Regulation Ripple & Noise P-P Max.
STRIDER ESSENTIAL SERIES SST-ST70F-ESB: Load +5V +3.3V +12V -12V +5Vsb Light Load 2.83A 2.83A 9.47A 0.05A 0.45A Typical Load 7.06A 7.06A 23.68A 0.14A 1.13A Full Load 14.13A 14.13A 47.35A 0.27A 2.25A +5V +3.3V +12V -12V +5Vsb Light Load 2.57A 2.57A 7.99A 0.05A 0.44A Typical Load 6.42A 6.42A 19.97A 0.13A 1.11A Full Load 12.83A 12.83A 39.93A 0.27A 2.22A SST-ST60F-ESB: Load 3.4 Rise Time DC output rise time is less than 20 mS at nominal line and full load. 3.
3.8 3.3V Sense A default 3.3V sense line should be implemented pin 13 of the connector. 3.9 Capacitive Load The power supply should be able to power up and operate normally with the following capacitances simultaneously present on the DC outputs. Output Capacitive load (uF) +5V 6000 +12V 8000 +3.3V 6000 -12V 350 +5VS 350 4. Protection 4.1 Input Protection In primary circuit of the power supply , a protected fuse is inserted. Only internal fault of the power supply will cause the fuse blown.
STRIDER ESSENTIAL SERIES 5. Start Stability 5.1 No Load Start When power is applied to ST70F-ESB and ST60F-ESB with no load connected or under minimum load connected, neither damage to power supply nor hazards to users will occur. 5.2 Cold Start The power supply shall operate properly when first applied at normal input voltage and or so maximum load after 4 hours storage in 0℃ environment. 6. Environments 6.1 Temperature and Humidity 6.1.1 Operating Temperature Relative Humidity 0 to 40℃ 20 to 90 % 6.1.
.3 Insulation Resistance The insulation resistance should be not less than 30M ohm after applying of 500VDC for 1 minute. 8.4 Dielectric Voltage Withstand The power supply shall withstand for 1 minute without breakdown the application of a 60Hz 1500V AC voltage applied between both input line and chassis (20mA DC cut-off current). Main transformer shall similarly withstand 3000Vac applied between both primary and secondary windings for a minimum of one minute. 9.
STRIDER ESSENTIAL SERIES 12.Power Factor The power supply with active power factor correction, and meet the EN61000-3-2 standards, The power factor is greater than 0.9 at 230V/50Hz, Max. load. 13.Mechanical Requirements 13.1 Physical Dimension 150 mm (W) × 86 mm (H) × 140mm (D) 13.
4PIN peripheral connector (HDD) Yellow Black Black Red Signal +12V COM COM +5VDC 4PIN floppy connector (FDD) Pin 1 2 3 4 Pin 1 2 3 4 Signal +5VDC COM COM +12V Red Black Black Yellow SATA connector Orange Black Red Black Yellow Signal Pin +3.
STRIDER ESSENTIAL SERIES Warranty Information Warranty terms & conditions 1.Product component defects or damages resulted from defective production is covered under warranty. Defects or damages with the following conditions will be fixed or replaced under SilverStone Technology’s jurisdiction. a)Usage in accordance with instructions provided in this manual, with no misuse, overuse, or other inappropriate actions.
NO.