GD05
Installation and system optimization guide: The following manual and guides were carefully prepared by the SilverStone engineering team to help you maximize the potential of your SilverStone product. Please keep this manual for future reference when upgrading or performing maintenance on your system. A copy of this manual can also be downloaded from our website at: http://www.silverstonetek.com 1 Specification P.2 Disassemble chart P.3 Installation guide P.4 Connector definition P.
GD05 A powerful, quiet, and versatile HTPC chassis for all occasions Aluminum skin over plastic front panel, 0.8mm SECC body Micro ATX, Mini-DTX, Mini-ITX Model No. SST-GD05B (Black) 5.25" x 1 3.5" x 2 , 2.5” x 1 or 3.5" x 1 , 2.5” x 2 Right Side 1 x 120mm intake fan, 1200rpm, 20dBA Also compatible with 80mm fan Left Side 2 x 120mm intake fans, 1200rpm, 20dBA Rear 2 x 80mm fan slots (optional mounting) 5 USB2.
3.5” x 2, 2.5” x 1 or 3.5 x 1, 2.5” x 2 TOP COVER 12025 FAN x 1 8025 FAN x 2(OPTION) PS2 PSU(OPTION) MICRO ATX M/B(OPTION) 12025 FAN x 2 POWER BUTTON RESET BUTTON USB2.0 x 2 +SPK+MIC 5.25”BAY QTY METAL SPACER 2 SCW-HW-6-32 SUCURE POWER SUPPLY OR PSU PKT AND MOTHERBOARD 13 SCW-HDD-6-32 SECURE 3.5"HARD DRIVE 8 SCW-PW-M3 SECURE OPTICAL AND 2.
lnstallation Guide Before you begin, please make sure that you (1) have all components collected (2) check that all components do not have compatibility problems with each other or with the case (3) if possible, assemble the components outside the case first to make sure they are working (4) keep the motherboard manual ready for reference during installation. 1 Unscrew the three screws from the rear of the chassis then remove the top cover.
lnstallation Guide 3 4 5 Unscrew two screws from the center brace to remove it. Открутите два шурупа на центральной скобе и выньте ее. Lesen Sie die beiden Schrauben an der mittleren Halterung, nehmen Sie die Halterung heraus. 鬆開中支架2顆螺絲,卸下中支架 Dévissez les deux vis de la barre centrale afin de la retirer. 松开中支架2颗螺丝,卸下中支架。 Desatornille dos tornillos del eje central para quitarlo. 中央の支柱のネジ2本を外して、 取り外します。 Svitare le due viti del gancio centrale per rimuoverlo. 중앙 버팀대의 2개의 나사를 제거합니다.
lnstallation Guide 6 Install power supply into the case, if the power supply is a little too deep, please install at an angle as shown in illustration A and B.
lnstallation Guide 7 Insert the I/O shield included with your motherboard, then install the motherboard into the case Установите заглушку для разъёмов задней панели материнской платы, прилагаемую к материнской плате, затем установите материнскую плату в корпус. Setzen Sie das mit Ihrem Motherboard 塞入I/O彈片,裝入主機板 gelieferte I/O-Blech in die Aussparungen an der Rückseite des Gehäuses ein, installieren Sie anschließend das Motherboard im Gehäuse.
lnstallation Guide 9 The tray areas around the motherboard have many small pass-through holes that can be used with included wire tie, please refer to the illustration for more information Вокруг материнской платы предусмотрено большое количество маленьких сквозных отверстий, которые можно использовать для прилагаемых стяжек для кабелей, см. рисунок.
lnstallation Guide 11 Now carefully count and separate the required power cables for your hard drive, optical drive, and graphics card. Place the needed cables out of the case and neatly place the unneeded power cables into available space inside the case Теперь аккуратно пересчитайте и отделите друг от друга силовые кабели для жесткого диска, оптического диска и графической карты. Нужные кабели вытащите из корпуса, а ненужные силовые кабели аккуратно разместите внутри корпуса.
lnstallation Guide 13 14 A B Install and secure required expansion cards Вставьте и закрепите карту расширения. Installieren und fixieren Sie benötigte Erweiterungskarten. 安裝並鎖固介面卡 Installez et fixez les cartes d'extensions nécessaires 安装并锁固介面卡。 Instale y fije las tarjetas de expansión necesarias. 必要な拡張カードをインストールし、 固定します。 Installare ed assicurare al case le schede di espansione in vostro possesso. 필요한 확장카드를 설치하고 고정시킵니다. Install and secure any 3.5” or 2.
lnstallation Guide 16 Reinstall hard drive bracket back into the case Вставьте кронштейн жесткого диска обратно в корпус. Bauen Sie die Festplattenhalterung wieder in das Gehäuse ein. 將硬碟架裝回機殼 Réinstallez le casier à disques durs dans le boîtier 请将硬盘架装回机箱。 Reinstale el bracket del disco duro en la carcasa. ハードドライブブラケット をケースに戻します。 Reinstallare la staffa degli hard disk nel case. 하드 드라이브 브라켓을 케이스에 재 설치합니다.
lnstallation Guide 21 Place the top cover back onto the case and secure with three screws. Установите на место верхнюю крышку корпуса и закрепите ее тремя шурупами. Setzen Sie die obere Abdeckung wieder auf das Gehäuse auf, fixieren Sie die Abdeckung mit drei Schrauben. 請將上蓋板蓋回去,並鎖固三顆螺絲 Remettez le panneau supérieur sur le 请将上侧板盖回,并锁固三颗螺丝。 boîtier et fixez-le avec trois vis. Vuelva a poner la cubierta superior en ケースに上部カバーを戻し、ネジ3本 la carcasa y asegúrela con tres tornillos.
Connector definition (1) Front panel connector installation Power switch and reset switch installation guide: Please refer to the motherboard manuals for the motherboard’s “Front Panel Connector” or “System Panel Connector” pin definition. Power switch and reset switch have no polarity, so they can be connected in any orientation.
Front I/O connector guide Below are the front I/O connectors pin definition, please also check your motherboard manual to cross reference with motherboard’s front I/O pin headers. SilverStone’s I/O connectors are in block type to simplify installation. Nachstehend finden Sie die Pinbelegung der Front-I/O-Verbinder; bitte gleichen Sie diese Angaben mit der Belegung der Front-I/O-Anschlüsse ab – diese Angaben finden Sie in Ihrer Motherboard-Dokumentation.
Component size limitations The GD05 was designed to be as small as possible while maximizing interior space usage, please refer to the following guidelines for component selection and future upgrade considerations. CPU cooler height limitation When optical drive is used, the GD05 has 70mm height limitation for CPU cooler. If no optical drive is installed, the height limit for CPU cooler increases to 120mm.
Power supply length limitation The allowable power supply length is determined by the left intake fan size. Please refer to the table below as a guide when choosing the appropriate power supply. Non-modular PSU Example Modular PSU Example Left case fan at 120mm Left case fan at 80mm PSU length limit is 180mm ZU1200M PSU length limit is 160mm ST70F PSU length limit is 220mm OP1200 PSU length limit is 200mm ST1000 The interior of the GD05 was designed with cable routing and room for excess cables.
Немодульный БП Пример Модульный БП Пример Левый вентилятор 120мм Левый вентилятор 80 мм Ограничение на длину блока питания - 180 мм ZU1200M Ограничение на длину блока питания - 160 мм ST70F Ограничение на длину блока питания - 220 мм OP1200 Ограничение на длину блока питания - 200 мм ST1000 Внутренность корпуса GD05 предназначена для прокладки кабелей, внутри корпуса предусмотрено место для неиспользуемых кабелей.
Upgrading case fan SilverStone already includes three 120mm low noise fans in the GD05. The fans are selected to maintain class-leading cooling performance while keeping noise to minimum. If you wish to increase air exhaust speed around the CPU, there are two 80mm fan slots for adding additional fans. For this, we recommend the use of SilverStone’s SUSCOOL81. SilverStone setzt drei geräuscharme 120-mm-Lüfter im GD05 ein.
Cleaning of fan filters on a regular basis is highly recommended GD05’s positive air pressure design is an effective configuration that will reduce dust buildup inside the case. Small air particles or lint will accumulate over time on GD05’s intake filters instead of on the components inside the case. To maintain GD05’s excellent cooling performance for years to come, we recommend to clean all fan filters regularly every three months or half a year (depending on your environment).
Fan and fan filter disassembly guide If you need to change fans, clean filters, or upgrade a fan, please refer to the following steps: 1 2 3 1.Refer to the case installation guide to properly remove the drive bracket, then loosen the fan screws to remove the fans. 2.Loosen the screws holding the fan filter to the fan to remove the fan filter 3.To remove the power supply fan filter, flip the case upside-down then loosen the screws holding the fan filter to remove it. 1.
Dual purpose space There is a dual purpose space located above the power supply area, it can be used for either of the two following application: A B A.Installation of a 3.5” hard drive B.Installation of a slot device or short expansion card such as extra motherboard I/O, fan controller, or daughter board (e.g. ASUS Xonar HDAV1.3) plus one 2.5” hard drive. Extra power supply rubber feet are included for providing support to expansion card installed above the power supply. A.
Expansion card removal guide Although GD05’s interior space is designed tightly, you can still install expansion cards without having to remove other brackets. Please refer to the following scenarios: (with the top cover already removed) If the rear hard drive’s cables are blocking the left expansion card, please first unplug the hard drive cables then proceed to remove/install the expansion card. Make sure to plug the cables back into the hard drive after installation.
(with the top cover already removed) If the expansion card on the right side is blocked by the card to the left, please first remove the card on the left side to allow the card on the right side to be removed without taking the center brace off the case. Falls die Erweiterungskarte auf der rechten Seite von der linken Karte blockiert wird, nehmen Sie zunächst die Karte auf der linken Seite heraus – so können Sie die rechte Karte entfernen, ohne die mittlere Halterung aus dem Gehäuse ausbauen zu müssen.
October, 2009 NO: G11210880
