User Manual

ManualsBrandsSilverStone Technology ManualsComputers & AccessoriesStrider 1200W 80 Plus Platinum Modular PSU 1200 Power Supply

Table Of Contents

ST1200-PT/ST1000-PT

STRIDER PLATINUM SERIES

The perfect balance of performance,

efficiency, and quality

High efficiency with 80 PLUS Platinum certification

139mm Air Penetrator fan with intelligent semi-fanless operation

FF141 magnetized fan filter included

100% modular cables

24/7 continuous power output with 40℃ operating temperature

Strict ±3% voltage regulation and low ripple & noise

Dual EPS 8pin with multiple individual one-on-one PCI-E 8/6pin connectors

Summary of content (8 pages)

PAGE 1
STRIDER PLATINUM SERIES ST1200-PT/ST1000-PT The perfect balance of performance, efficiency, and quality High efficiency with 80 PLUS Platinum certification 139mm Air Penetrator fan with intelligent semi-fanless operation FF141 magnetized fan filter included 100% modular cables 24/7 continuous power output with 40℃ operating temperature Strict ±3% voltage regulation and low ripple & noise Dual EPS 8pin with multiple individual one-on-one PCI-E 8/6pin connectors
PAGE 2
SPECIFICATION SilverStone Strider Platinum SST-ST1200-PT SST-ST1000-PT ATX12V / EPS 12V Switching Power Supply With Active PFC 80Plus Platinum PS/2 This specification describes the requirements of 1000W,1200Watts switching power supply with an stretch ATX form-factor and EPS 12V, +5V standby voltage, remote on/off control, full range line input capability and forced air cooling characteristics. 1. AC INPUT 1.
PAGE 3
Table 2 AC Input Line Requirements Parameter Min. Nom. Max. Unit Vin( Full range ) 105 115---240 264 VACrms Vin Frequency 47 60-----50 63 Hz Iin(1200W) 12.6---6 or 12---6 Arms Power factor correction (PF)>0.90 at full load. The power supply must meet inrush requirements for any rated AC voltage, during turn on at any phase of AC voltage, during a single cycle AC dropout condition, during repetitive ON/OFF cycling of AC, and over the specified temperature range (Top).
PAGE 4
2.2.2:(ST1200-PT Load Range) Parameter Min(optional) Nom. Max Peak Unit +3.3V 0.1 - 25 Amps +5V 0.2 - 22 Amps +12V 0.15 - 100 Amps -12V 0 - 0.3 Amps +5VSB 0 - 2.5 Amps 1.Maximum continuous total DC output power should not exceed 1200W. 2.Maximum continuous combined load on +3.3V and +5V outputs shall not exceed 120W. 3.Maximum combined current for the +12V outputs shall be 100A(1200W). 4.Peak DC output power should not exceed 1250W for 12 second. 2.3 Output Ripple 2.3.
PAGE 5
2.4 Overshoot Any overshoot at turn on or turn off shall be less 10% of the norminal voltage value, all outputs shall be within the regulation limit of section 2.0 before issuing the power good signal of section 5.0. 2.5 Efficiency Power supply efficiency typical 90% / 20% Load, 92% / 50% Load, 89% / 100% Load at normal AC main voltage. 2.6 Remote ON/OFF control When the logic level "PS-ON" is low, the DC outputs are to be enabled.
PAGE 6
3.4 Under voltage protection. In an under voltage fault occurs, the supply will latch all DC outputs into a shutdown state when +12V, +5V & +3.3V outputs under 85% of it's maximum value. 3.5 Over voltage protection The over voltage sense circuitry and reference shall reside in packages that are separate and distinct from the regulator control circuity and reference. No single point fault shall be able to cause a sustained over voltage condition on any or all outputs.
PAGE 7
Figure 2. PS-OK Timing Sequence (1)T3: Power good signal turn on delay time (100ms~500ms) (2)T4: Power good signal turn off delay time (75%Load 1ms min) (3)T2: Rise time (0.1~20ms) (4)T6: Hold up time (75%Load 16ms) 4.2 Hold up time When the power loss its input power, it shall maintain 16ms in regulation limit at normal input voltage and 75% full load (AC:115V/60Hz or 230V/50Hz) 5. ENVIRONMENT 5.1 Operation Temperature Relative Humidity 0 to 40℃ 10 to 90%, non-condensing 5.
PAGE 8
NO.