Manual

4
GB
Specification
Input .....................................................230V ~ 50Hz
Charging output voltage .......................12V/24V
Min. Ah rating .......................................60Ah
Max. Ah rating ......................................200Ah
Max output current ...............................18A at 12V
12A at 24V
Protection Class ...................................
As part of our ongoing product development, specifications
of Silverline products may alter without notice.
General Safety Instructions
Carefully read and understand this manual and any label before use.
Keep these instructions with the product for future reference. Ensure all persons
who use this product are fully acquainted with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe manner in
which to use this product, do not attempt to use it.
Keep guards in position
Always keep guards in position, in good working order, correctly adjusted and •
aligned. Never attempt to use a tool if any of the supplied guards are missing. If
any guards are damaged, replace before use.
Remove adjusting keys
Always check to see that keys and adjusting devices are removed from the •
tool before use.
Clean the work area
Accidents can occur where benches and work areas are cluttered or dirty, •
floors must be kept clear, avoid working where the floor is slippery. If working
outdoors, make yourself aware of all potential slip and trip hazards before
using this tool.
Children and pets
Children and pets should always be kept at a safe distance from your work •
area. Lock tools away where children can’t get access to them. Do not allow
children, or untrained persons to use this tool.
Use the correct tool
Do not force, or attempt to use a tool for a purpose for which it was not •
deisgned.
Keep your balance
Do not over reach, keep proper footing at all times, do not use tools when •
standing on an unstable surface.
Accessories
The use of any attachment or accessory other than those mentioned in this •
manual could result in damage or injury. The use of improper accessories could
be dangerous, and will invalidate your warranty.
Secure work
Always ensure work is secure, if appropriate use a clamp or vice.•
Check for damaged or missing parts
Before each use, check if any part of the tool is damaged or missing, check •
carefully that it will operate properly and perform its intended function. Check
alignment of moving parts for binding. Any guard or other part that is damaged
should be immediately repaired or replaced. Do not use if defective.
Electrical Safety
• Thewiresinthisproductarecoloured:
Blue Neutral (N)
Brown Live (L)
Green & Yellow Earth (E)
As the colours may not correspond with the coloured markings in your plug, •
proceed as follows.
The wire which is coloured blue must be connected to the terminal which is •
marked with the letter N or coloured black, the wire which is coloured brown
must be connected to the terminal which is marked L or coloured red.
This appliance must be protected by a suitable fuse.•
To prevent fire or shock hazard, do not expose this product to rain, water or •
moisture.
There are no user serviceable parts inside except those referred to in this •
manual. Always refer servicing to qualified service personnel. Never remove
any part of the casing unless qualified to do so; this unit contains dangerous
voltages.
Use of a residual current device (RCD) will reduce the risk of electric shock.•
NEVER CONNECT THE BROWN OR BLUE WIRE TO THE EARTH PIN OF THE
13 AMP PLUG. IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN
Dangerous environment
Do not use power tools in damp or wet conditions, or expose them to •
rain. Provide adequate surrounding work space and keep area well
lit. Do not use power tools where there is a risk of explosion or fire from
combustible material, flammable liquids, flammable gases, or dust of an
explosive nature. When using power tools avoid contact with any earthed items
such as pipes, radiators, cookers, refrigerators, metal baths and taps.
Protect yourself from vibration
Hand held power tools may produce vibration. Vibration can cause disease. •
Gloves to keep the operator warm may help to maintain good blood circulation
in the fingers. Hand held tools should not be used for long periods without a
break.
Maintain your power tool
Ensure all ventilation holes are kept clear at all times. Overheating and fire may •
otherwise result.
Always disconnect
Before changing fittings or accessories, always ensure that your tool is •
disconnected from the power source.
Switch off before connecting
Ensure that the power tool is switched off before connecting to the power •
source. If the power tool stops unexpectedly, turn the power switch to off.
Description of Symbols
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction Manual.
Class I construction (Protective earth).
Conforms to relevant legislation and safety standards.
Environmental Protection
Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your local
authority or retailer for recycling advice.
178555_Instructions.indd 4 10/11/10 16:59:07