Electric Fireplace SEKU 2000 A1 6 Electric Fireplace Operating instructions KOMPERNASS GMBH BURGSTRASSE 21 · D-44867 BOCHUM www.kompernass.com ID-Nr.
Contents GB IE Introduction . . . . . . . . . . . . . . . . . . . . . . 2 Information for these operating instructions . . . . . 2 Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Limited liability . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . 10 Safety . . . . . . . .
Introduction Introduction GB IE Information for these operating instructions These operating instructions are a component of the SEKU 2000 A1 Electric Fireplace (henceforth designated as the appliance) and they provide you with important information about the intended use, safety, installation and connection as well as operation of the appliance. These operating instructions must at all times be kept available close to the appliance.
Introduction Warnings GB IE In these operating instructions the following warnings are used: DANGER A warning at this danger level indicates a threateningly dangerous situation. If the dangerous situation is not avoided, it could result in death or serious injury. ► Compliance with the instructions in this warning is necessary to avoid the risk of death or serious injury. WARNING A warning at this danger level indicates a potentially dangerous situation.
Safety Safety GB IE In this chapter you are being given important safety information regarding the handling of the appliance. This appliance complies with the statutory safety regulations. Incorrect usage can, however, lead to personal and property damage.
Setting up and connecting ■ Defective components may only be replaced with original replacement parts. Only by using original replacement parts can it be guaranteed that the safety requirements are being complied with. ■ Protect the appliance from moisture and liquid penetration. ■ Always pull on the plug when disconnecting from the mains power socket, never pull on the connection cable. ■ Do not use the appliance adjacent to open flames.
Setting up and connecting Installation requirements GB IE For the safe and correct operation of the appliance, the installation site must satisfy the following requirements: ■ The appliance must be placed on a firm, flat and horizontal surface. ■ Do not place the appliance in a hot, wet or very humid environment or close to inflammable materials. ■ The mains power socket must be easily accessible at all times, thus enabling the plug to be immediately withdrawn should an emergency situation arise.
Operating components Operating components GB IE NOTICE ► The operating elements are on the front of the appliance, above right and behind the ventilation grille. ► To operate them, fold the ventilation grille forward.
Set up Set up GB IE Before the appliance can be set up, the fire surround must be assembled. NOTICE ► Check the contents to make sure everything is there and for visible damage. ► Firstly, become familiar with all parts involved in the assembly.
Set up Screws and assembly material A No.: B C GB IE E D A Designation: Screws 6 x 25 mm B Wood plugs 8 C Double locking pin 4 D Single locking pin 6 E Adapter sleeve 14 F Fixing device 2 F Number: 17 NOTICE ► You require a screwdriver for the assembly; this is not supplied. The assembly of the fire surround is described in detail in the following. NOTICE ► Carry out the assembly step by step in the order as described.
Assembly GB IE Assembly Step 1 Screw three single locking pins Place two wood plugs Insert three adapter sleeves E into the three large holes of the left side panel . Thereby, with the screwdriver line up the adaptor sleeves E so that the arrow on the adaptor sleeves points to the outer edge of the side panel . B D with a screwdriver into the prepared holes on the left front panel into the holes of the front panel 2 2 . .
Assembly Then, bring the front panel 4 and side panel 8 together at right angles, so that the locking pins enter the holes on the right edge of the side panel. When done, screw all three adapter sleeves E to the right with the screwdriver until the locking pins are clamped into the adapter sleeves and the panels are seated firmly together and at right angles. D Step 3 Take the centre front panel Then place four adapter sleeves E in the four large holes.
Assembly Step 5 GB IE 7 Place the floor plate on the floor. Now take the previously assembled unit and carefully place it on the floor plate as shown in the following diagramme. Then screw together the assembled unit with the connection blocks 8 screws of the type A . (2 screws per connection block). G on the floor plate 7 . For this, use G G A A Step 6 Take the top covering panel Secure the top covering panel 3 and place it on the preassembled unit.
Assembly Step 7 6 Take the base plate and insert 4 wood plugs Then place the base plate the floor plate. 6 on the floor plate B 7 GB IE into the holes of the plate underside. so that the four wood plugs fit into the four holes in Rear view Front View 6 B B 7 Installing the appliance in the fire surround To finalise, install the appliance in the assembled fire surround.
Handling and operation/Maintenance GB IE Handling and operation NOTICE ► See also "Operating Elements" on page 7. In this chapter you receive important information for the handling and operation of the appliance. Activate the ON/OFF switch to turn the unit on. The flame replication lights up. Programme in the desired brightness with the Dimmer 5 . Then, turn the heater on with the switch 1 (1000 W).
Maintenance/Cleaning/Troubleshooting Switch the appliance off. Pull the plug from the mains power socket. Loosen the four screws on the rear panel and remove the metal ventilation panel Carefully replace the defective bulb 10 Screw the metal ventilation panel back onto the appliance rear. 9 9 GB IE . in the light shaft. 11 10 9 Cleaning WARNING Observe the following safety information to avoid risks and property damage: ► Clean the appliance ONLY when it is switched off and cold.
Troubleshooting/Storage/Disposal GB IE Malfunction causes and remedies The following table will help with localising and remedying minor malfunctions: Defect The flame replication does not light up. Possible cause Solution The appliance is not switched on. Switch the appliance on. The plug is not inserted. Insert the plug into the mains power socket. The mains power socket does not supply voltage The bulbs are defect. Check the fuses Replace the defective bulbs. The appliance does not heat.
Appendix Appendix GB IE Technical data General Input voltage 220 - 240 V~ 50 Hz 1000 2000 W W 2 x 25 W +5 to +45 °C Humidity (no condensation) 5 to 90 % Measurements (W x H x D): 100 x 100 x 39 cm approx.
Appendix GB IE Warranty You receive a 3-year warranty for this appliance as of the purchase date. The appliance has been manufactured with care and meticulously examined before delivery. Please retain your receipt as proof of purchase. In the case of a warranty claim, please make contact by telephone with our Service Department. Only in this way can a post-free despatch for your goods be assured.
