ReVit TM EN FR NL ES GR NO info@silkn.com www.silkn.
14. Labeling Class II equipment WEEE - Waste Electrical and Electronic Equipment CE Mark Do not use this appliance in a wet surrounding Degree of protection against ingress water: ordinary This device is not suitable for use in the presence of flammable anesthetic mixture with air or with Oxygen or Nitrous Oxide.
English Copyright 2013 © Home Skinovations Ltd. All rights reserved. Print date: February 2014 Home Skinovations Ltd. reserves the right to make changes to its products or specifications to improve performance, reliability, or manufacturability. Information furnished by Home Skinovations Ltd. Is believed to be accurate and reliable at the time of publication. However, Home Skinovations Ltd. assumes no responsibility for its use.
English Before using Revit™ for the first time, please read this User Manual in its entirety. Pay particular attention to procedures for using and operating the device and after-use procedures.
D F Coarse Fine Precision The Revit™ dermabrasion device has 3 FILING TIPS (A) connected to a RUBBERIZED GRIP (B) with a REPLACABLE FILTER (C), installed on the FRONT COVER CONE (D), AIR VENTS (E) located on the FRONT COVER (F) and an ON BUTTON (G) which is also the Suction Intensity Regulator found on the REAR COVER (H). The AC adaptor cord connects to the bottom of the device English 2. Revit™ device description C B A E G 3.
English 4. Revit™ Intended Use The Revit™ is an over the counter device intended for the exfoliation of the upper layers of the skin, for a fresher appearance. It is intended for the treatment of: Aging skin of body face and neck Fine facial lines Lines around the eyes Skin discoloration Dark spots and scarring Dull and sun damaged skin 5. Safety with Revit™ 5.
English 6. Precautions – How to use Revit™ Safely It is advised that you start treatment using the finest tip set to Partial Suction Mode on a small skin area. If you see no adverse reaction, you can start treatment on full areas but still with the finest tip set on Partial Suction Mode. If your skin does not show any adverse signs, you can start treating with all other tips on Full Suction Mode. 6.
English Revit™ should never be left unattended when plugged into an outlet. Do not operate Revit™ if it has a damaged cord or plug and keep the power cord away from heated surfaces. Do not use Revit™ if you see or smell smoke when it is in use. Do not use Revit™ if any or all vents in its GRIP are blocked. Do not use Revit™ if any of its part are cracked, broken, or coming apart Unplug Revit™ before cleaning. Do not use Revit™ with any attachments or accessories not recommended by Home Skinovations Ltd.
English Covering skin areas Neck area We recommend you start with the lower suction intensity and increasing after a few uses, depending on your comfort level and skin sensitivity. Using smooth, downwards strokes, work the neck area Forehead, cheeks and chin We recommend you start with the lower suction intensity and increasing after a few uses, depending on your comfort level and skin sensitivity. Firmly stroke from the center outwards, towards the hairline.
English 10. After treating with Revit™ When a Revit™ session has been completed, turn Revit™ off by giving the ON BUTTON one quick press if you are on Full Suction Mode, or two quick presses if you are treating on Partial Suction Mode Unplug the power cord from the electrical outlet. It is recommended that you inspect the REPLACABLE FILTER every few treatments for skin fallout blockage. It is also important that you clean the FILING TIP periodically.
12. Troubleshooting “My Revit™ does not start.” Make sure the power cord is properly connected to the Revit™ device. Make sure the power cord is plugged into an electrical outlet on the wall. “The suction is weak” Make sure you have good contact with the skin and that the treatment surface is evenly and firmly pressed to the skin. Make sure you are on FULL SUCTION mode. To check this, give the ON BUTTON a quick press. If suction increases, you were working on PARTIAL SUCTION mode.
English 13. Customer Service For more information about Silk’n™ products please enter your local Silk’n™ website, www.silkn.eu or www.silkn.com. If your device is broken, damaged, in need of repair, or for any other user assistance, please contact your local Silk’n™ Customer Service: For USA and Canada customers: 1-877-DO-SILKN / 1-877-367-4556, contact@silkn.com For customers in other countries: info@silkn.com 14.
