Data Sheet

ManualsBrandsSilicon Labs ManualsElectronicsZigbee and Bluetooth Low Energy wireless radio modules

Table Of Contents

Confidential

MGM220P Wireless Gecko Bluetooth

Module Data Sheet

The MGM220P is a module designed and built to meet the per-

formance, security, and reliability requirements of battery-powered

IoT products for mesh networks.

Based on the EFR32MG22 SoC, the MGM220P enables Zigbee Green Power

and

Bluetooth

Low Energy connectivity while delivering best-in-class RF range and per-

formance, future-proof capability for feature and OTA firmware updates, enhanced se-

curity features, and low energy consumption.

MGM220P modules are a full solution that comes with fully-upgradeable, robust soft-

ware stacks, world-wide regulatory certifications, advanced development and debugging

tools, and support that will minimize and simplify the engineering and development of

your end-products helping to accelerate their time-to-market.

The MGM220P is intended for a broad range of applications, including:

• Connected Home

• Building Automation and Security

KEY FEATURES

• Zigbee Green Power and Bluetooth 5.2

Connectivity

• Bluetooth Low Energy

• Built-in antenna

• Up to 8 dBm TX power

• -98.9 dBm BLE RX sensitivity at 1 Mbps

• 32-bit ARM Cortex-M33 core at up to 76.8

MHz

• 512/32 kB of Flash/RAM memory

• Optimal selection of MCU peripherals

• Up to 24 GPIO pins

• 12.9 mm x 15.0 mm

Lowest power mode with peripheral operational:

EM4—Shutoff

EM3—StopEM2—Deep SleepEM1—SleepEM0—Active

Timers and Triggers

32-bit bus

Peripheral Reflex System

Serial

Interfaces

I/O Ports

Analog I/F

USART

EUART

External

Interrupts

General

Purpose I/O

Pin Reset

Pin Wakeup

ADC

Energy

Management

Brown-Out

Detector

Voltage

Regulator

Power-On

Reset

SecurityClock Management

HF Crystal

Oscillator

LF Crystal

Oscillator

LF RC

Oscillator

RC Oscillator

Crypto Acceleration

Ultra LF RC

Oscillator

Core / Memory

ARM Cortex

M33 processor

with DSP extensions,

FPU and TrustZone

ETM Debug Interface RAM Memory

LDMA

Controller

Flash Program

Memory

Real Time

Capture

Counter

Timer/

Counter

Low Energy

Timer

Watchdog

Timer

Protocol

Timer

True Random

Number Generator

Fast Startup

RC Oscillator

Back-Up Real

Time Counter

PDM

DC-DC

Converter

Temperature

Sensor

Radio Subsystem

RFSENSE

w/ OOK Detect

RX/TX Frontend

with Integrated

+8 dBm PA

Frequency

Synthesizer

ARM Cortex

M0+ Radio

Controller

CRC

BUFC RAM

FRC

DEMOD

AGC

IFADC

MOD

Crystals

Antenna

Chip Antenna

Matching

38.4 MHz

32.768

kHz

silabs.com | Building a more connected world. Preliminary Rev. 0.5

This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Silicon

Laboratories Confidential. Information contained herein is covered under non-disclosure agreement (NDA).

Summary of content (47 pages)

PAGE 1
C MGM220P Wireless Gecko Bluetooth Module Data Sheet on The MGM220P is a module designed and built to meet the performance, security, and reliability requirements of battery-powered IoT products for mesh networks. KEY FEATURES • Zigbee Green Power and Bluetooth 5.
PAGE 2
MGM220P Wireless Gecko Bluetooth Module Data Sheet Feature List 1. Feature List • Wide Operating Range • 1.8 to 3.8 V • -40 to +105°C • Dimensions • 12.9 mm x 15.
PAGE 3
MGM220P Wireless Gecko Bluetooth Module Data Sheet Ordering Information 2. Ordering Information Table 2.1. Ordering Information Ordering Code MGM220PC22HNA2 Protocol Stack TX Power Rating • Zigbee 8 dBm • Bluetooth 5.2 • Direction finding Antenna RF Shield Built-in Yes Flash (kB) RAM (kB) LF Clock GPIO Temp Range 512 32 Crystal 24 -40 to 105 °C C tia en fid on Note: 1.
PAGE 4
Table of Contents 1. Feature List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.1 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.2 EFR32MG22 SoC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.3 Antenna . . . . . . .
PAGE 5
7. Design Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 7.1 Layout and Placement . . . . . . . . . . . . . . . . . . . . . . . . . . .31 7.2 Proximity to Other Materials . . . . . . . . . . . . . . . . . . . . . . . . .32 7.3 Proximity to Human Body . . . . . . . . . . . . . . . . . . . . . . . . . .32 8. Package Specifications 8.1 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 6
MGM220P Wireless Gecko Bluetooth Module Data Sheet System Overview 3. System Overview 3.1 Block Diagram The MGM220P module combines an energy-friendly MCU with a highly integrated radio transceiver in a PCB module with a robust, integrated antenna. This section gives a short introduction to the features of the module. The block diagram for the MGM220P module is shown in Figure 3.1 MGM220P Block Diagram on page 6.
PAGE 7
MGM220P Wireless Gecko Bluetooth Module Data Sheet System Overview 3.2 EFR32MG22 SoC The EFR32MG22 SoC features a 32-bit ARM Cortex M33 core, a 2.4 GHz high-performance radio, 512 kB of flash memory, a rich set of MCU peripherals, and various clock management and serial interfacing options. Consult the EFR32xG22 Wireless Gecko Reference Manual and the EFR32MG22 Data Sheet for details. 3.3 Antenna MGM220P modules include a ceramic chip antenna on board with the characteristics detailed in the table below.
PAGE 8
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4. Electrical Characteristics All electrical parameters in all tables are specified under the following conditions, unless stated otherwise: • Typical values are based on TA=25 °C and VDD supply at 3.0 V, by production test and/or technology characterization.
PAGE 9
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.2 General Operating Conditions This table specifies the general operating temperature range and supply voltage range for all supplies. The minimum and maximum values of all other tables are specifed over this operating range, unless otherwise noted. Table 4.2.
PAGE 10
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.2.1 DC-DC Operating Limits Tj ≤ 85 °C Tj ≤ 105 °C 60 5 on C Average Lifetime ILOAD (mA) The maximum supported voltage on the VDD supply pin is limited under certain conditions. Maximum input voltage is a function of temperature and the average load current over a 10-year lifetime. Figure 4.1 Lifetime average load current limit vs. Maximum input voltage on page 10 shows the safe operating region under specific conditions.
PAGE 11
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.3 MCU Current Consumption with 3 V Supply Unless otherwise indicated, typical conditions are: Module supply voltage = 3.0 V. Voltage scaling level = VSCALE1. TA = 25 °C. Minimum and maximum values in this table represent the worst conditions across process variation at TA = 25 °C. Table 4.3.
PAGE 12
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics Parameter Symbol Current consumption in EM4 IEM4 mode Additional current in EM2 or EM3 when any peripheral in PD0B is enabled1 Test Condition No BURTC, No LF Oscillator, DCDC bypassed IPD0B_VS Min Typ Max Unit — 0.17 — µA — 0.37 — µA Note: 1. Extra current consumed by power domain. Does not include current associated with the enabled peripherals. See for a list of the peripherals in each power domain. C 4.
PAGE 13
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.5 RF Transmitter General Characteristics for the 2.4 GHz Band Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Table 4.5. RF Transmitter General Characteristics for the 2.4 GHz Band Parameter Symbol RF tuning frequency range FRANGE Maximum TX power1 POUTMAX C Minimum active TX Power POUTMIN Test Condition Typ Max Unit 2400 — 2483.
PAGE 14
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.7 RF Receiver Characteristics for 802.15.4 DSSS-OQPSK in the 2.4 GHz Band Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Table 4.7. RF Receiver Characteristics for 802.15.4 DSSS-OQPSK in the 2.4 GHz Band Symbol Test Condition Min Typ Max Unit Max usable receiver input level, 1% PER SAT Signal is reference signal1.
PAGE 15
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.8 RF Receiver Characteristics for Bluetooth Low Energy in the 2.4 GHz Band 1 Mbps Data Rate Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Table 4.8. RF Receiver Characteristics for Bluetooth Low Energy in the 2.
PAGE 16
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.9 RF Receiver Characteristics for Bluetooth Low Energy in the 2.4 GHz Band 2 Mbps Data Rate Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Table 4.9. RF Receiver Characteristics for Bluetooth Low Energy in the 2.
PAGE 17
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.10 RF Receiver Characteristics for Bluetooth Low Energy in the 2.4 GHz Band 500 kbps Data Rate Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Table 4.10. RF Receiver Characteristics for Bluetooth Low Energy in the 2.
PAGE 18
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.11 RF Receiver Characteristics for Bluetooth Low Energy in the 2.4 GHz Band 125 kbps Data Rate Unless otherwise indicated, typical conditions are: TA = 25 °C, VDD = 3.0V. RF center frequency 2.45 GHz. Table 4.11. RF Receiver Characteristics for Bluetooth Low Energy in the 2.
PAGE 19
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.12 High-Frequency Crystal Table 4.12. High-Frequency Crystal Parameter Symbol Crystal frequency Test Condition Typ Max Unit fHFXTAL — 38.4 — MHz Initial calibrated accuracy ACCHFXTAL -10 +/-5 10 ppm Temperature drift DRIFTHFXTAL -20 — 20 ppm Min Typ Max Unit — 32.768 — kHz -100 — 100 ppm -150 — 150 ppm C Min Across specified temperature range 4.13 Low-Frequency Crystal on Table 4.
PAGE 20
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.15 GPIO Pins Unless otherwise indicated, typical conditions are: VDD = 3.0 V. Table 4.15. GPIO Pins Parameter Symbol Test Condition Leakage current ILEAK_IO C Input low voltage1 VIL Typ Max Unit MODEx = DISABLED, VDD = 1.71V — 1.9 — nA MODEx = DISABLED, VDD = 3.0 V — 2.5 — nA MODEx = DISABLED, VDD = 3.3 V TA = 105 °C — — TBD nA Any GPIO pin — — 0.3 * VDD V RESETn — — 0.3 * DVDD V 0.
PAGE 21
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.
PAGE 22
MGM220P Wireless Gecko Bluetooth Module Data Sheet Electrical Characteristics 4.17.1 Antenna Radiation and Efficiency Typical MGM220P radiation patterns and efficiency for the on-board chip antenna under optimal operating conditions are plotted in the figures that follow. Antenna gain and radiation patterns have a strong dependence on the size and shape of the application PCB the module is mounted on, as well as on the proximity of any mechanical design to the antenna. en fid on C Figure 4.3.
PAGE 23
MGM220P Wireless Gecko Bluetooth Module Data Sheet Reference Diagrams 5. Reference Diagrams 5.1 Network Co-Processor (NCP) Application with UART Host The MGM220P can be controlled over the UART interface as a peripheral to an external host processor. Typical power supply, programming/debug interface, and host interface connections are shown in the figure below. For more details, refer to AN958: Debugging and Programming Interfaces for Custom Designs.
PAGE 24
MGM220P Wireless Gecko Bluetooth Module Data Sheet Reference Diagrams 5.2 SoC Application The MGM220P can be used in a stand-alone SoC configuration without an external host processor. Typical power supply and programming/debug interface connections are shown in the figure below. For more details, refer to AN958: Debugging and Programming Interfaces for Custom Designs.
PAGE 25
MGM220P Wireless Gecko Bluetooth Module Data Sheet Pin Definitions 6. Pin Definitions 6.1 31-Pin PCB Module With LF Crystal Device Pinout tia en fid on C Figure 6.1. 31-Pin PCB Module With LF Crystal Device Pinout The following table provides package pin connections and general descriptions of pin functionality. For detailed information on the supported features for each GPIO pin, see 6.2 Alternate Function Table, 6.3 Analog Peripheral Connectivity, and 6.4 Digital Peripheral Connectivity. Table 6.
PAGE 26
MGM220P Wireless Gecko Bluetooth Module Data Sheet Pin Definitions Pin Name Pin(s) Description Pin Name Pin(s) Description 11 GPIO GND 12 VDD 13 Power supply PA05 14 GPIO PA06 15 GPIO PA07 16 GPIO PA08 17 GPIO PD03 18 GPIO PD02 19 GPIO GND 20 NC 21 PC00 22 GPIO PC01 23 GPIO PC02 24 GPIO PC03 25 GPIO PC04 26 GPIO PC05 27 GPIO PC06 28 GPIO PC07 29 GPIO RESETn 30 Reset Pin. The RESETn pin is pulled up to an internal DVDD supply.
PAGE 27
MGM220P Wireless Gecko Bluetooth Module Data Sheet Pin Definitions 6.3 Analog Peripheral Connectivity Many analog resources are routable and can be connected to numerous GPIO's. The table below indicates which peripherals are avaliable on each GPIO port. When a differential connection is being used Positive inputs are restricted to the EVEN pins and Negative inputs are restricted to the ODD pins. When a single ended connection is being used positive input is avaliable on all pins.
PAGE 28
MGM220P Wireless Gecko Bluetooth Module Data Sheet Pin Definitions 6.4 Digital Peripheral Connectivity Many digital resources are routable and can be connected to numerous GPIO's. The table below indicates which peripherals are avaliable on each GPIO port. Table 6.4. DBUS Routing Table Peripheral.Resource PORT PA PD CMU.CLKIN0 Available Available CMU.CLKOUT0 Available Available CMU.CLKOUT1 Available Available C PC CMU.
PAGE 29
MGM220P Wireless Gecko Bluetooth Module Data Sheet Pin Definitions Peripheral.Resource PORT PA PB PD MODEM.DIN Available Available MODEM.DOUT Available Available PDM.CLK Available Available Available Available PDM.DAT0 Available Available Available Available PDM.DAT1 Available Available Available Available PRS.ASYNCH0 Available Available PRS.ASYNCH1 Available Available PRS.ASYNCH10 Available Available PRS.
PAGE 30
MGM220P Wireless Gecko Bluetooth Module Data Sheet Pin Definitions Peripheral.Resource PORT PA PB PD TIMER2.CDTI0 Available Available TIMER2.CDTI1 Available Available TIMER2.CDTI2 Available Available TIMER3.CC0 Available Available TIMER3.CC1 Available Available TIMER3.CC2 Available Available TIMER3.CDTI0 Available Available TIMER3.CDTI1 Available Available TIMER3.CDTI2 Available Available on C PC TIMER4.CC0 Available Available TIMER4.CC1 Available Available TIMER4.
PAGE 31
MGM220P Wireless Gecko Bluetooth Module Data Sheet Design Guidelines 7. Design Guidelines 7.1 Layout and Placement For optimal performance of the MGM220P, • • • • • Place the module aligned to the edge of the application PCB, as illustrated in the figures below. Leave the antenna clearance area void of any traces, components, or copper on all layers of the application PCB. Connect all ground pads directly to a solid ground plane. Place the ground vias as close to the ground pads as possible.
PAGE 32
MGM220P Wireless Gecko Bluetooth Module Data Sheet Design Guidelines The width of the GND plane to the sides the module will impact the efficiency of the on-board chip antenna. To achieve optimal performance, a GND plane width of 50 mm is recommended. See 4.17.1 Antenna Radiation and Efficiency for reference. 7.2 Proximity to Other Materials Avoid placing plastic or any other dielectric material in close proximity to the antenna.
PAGE 33
MGM220P Wireless Gecko Bluetooth Module Data Sheet Package Specifications 8. Package Specifications 8.1 Dimensions tia en fid on C l Figure 8.1. Module Dimensions silabs.com | Building a more connected world. Preliminary Rev. 0.
PAGE 34
MGM220P Wireless Gecko Bluetooth Module Data Sheet Package Specifications 8.2 PCB Land Pattern tia en fid on C silabs.com | Building a more connected world. l Figure 8.2. Land Pattern Preliminary Rev. 0.
PAGE 35
MGM220P Wireless Gecko Bluetooth Module Data Sheet Package Specifications 8.3 Package Marking The figure below shows the module markings engraved on the RF shield. on C Figure 8.3. MGM220P Top Marking fid Mark Description tia en The package marking consists of: • MGM220Pxxxxxxx - Part number designation • Model: MGM220Pxxx - Model number designation • QR Code: YYWWMMABCDE • YY – Last two digits of the assembly year. • WW – Two-digit workweek when the device was assembled.
PAGE 36
MGM220P Wireless Gecko Bluetooth Module Data Sheet Soldering Recommendations 9. Soldering Recommendations It is recommended that final PCB assembly of the MGM220P follows the industry standard as identified by the Institute for Printed Circuits (IPC). This product is assembled in compliance with the J-STD-001 requirements and the guidelines of IPC-AJ-820. Surface mounting of this product by the end user is recommended to follow IPC-A-610 to meet or exceed class 2 requirements.
PAGE 37
MGM220P Wireless Gecko Bluetooth Module Data Sheet Tape and Reel 10. Tape and Reel MGM220P modules are delivered to the customer in cut tape (100 pcs) or reel (1000 pcs) packaging with the dimensions below. All dimensions are given in mm unless otherwise indicated. en fid on C Figure 10.1. Carrier Tape Dimensions tia l Figure 10.2. Reel Dimensions silabs.com | Building a more connected world. Preliminary Rev. 0.
PAGE 38
MGM220P Wireless Gecko Bluetooth Module Data Sheet Certifications 11. Certifications This section details the regulatory certification status of the module in various regions. The address for the module manufacturer and certification applicant is: SILICON LABORATORIES FINLAND OY Alberga Business Park, Bertel Jungin aukio 3, 02600 Espoo, Finland 11.1 Qualified Antennas C MGM220P modules have been tested and certified with the on-board chip antenna.
PAGE 39
MGM220P Wireless Gecko Bluetooth Module Data Sheet Certifications OEM Responsibilities to comply with FCC Regulations This module has been tested for compliance to FCC Part 15. OEM integrators are responsible for testing their end-product for any additional compliance requirements needed with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
PAGE 40
MGM220P Wireless Gecko Bluetooth Module Data Sheet Certifications Class B Device Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 41
MGM220P Wireless Gecko Bluetooth Module Data Sheet Certifications 11.4 ISED Canada ISED This radio transmitter (IC: 5123A-GM220P) has been approved by Innovation, Science and Economic Development Canada (ISED Canada, formerly Industry Canada) to operate with the embedded antenna and with the antenna type(s) listed in 11.1 Qualified Antennas, with the maximum permissible gain indicated.
PAGE 42
MGM220P Wireless Gecko Bluetooth Module Data Sheet Certifications ISEDC (Français) Le présent émetteur radio (IC: 5123A-GM220P) a été approuvé par Innovation, Sciences et Développement Économique Canada (ISED Canada, anciennement Industrie Canada) pour fonctionner avec l'antenne intégrée et le ou les types d'antenne énumérés à la section 11.1 Qualified Antennas, avec le gain maximal admissible indiqué.
PAGE 43
MGM220P Wireless Gecko Bluetooth Module Data Sheet Certifications 11.5 Proximity to Human Body When using the module in an application where the radio is located close to the human body, the human RF exposure must be evaluated. FCC, ISED, and CE all have different standards for evaluating the RF exposure, and because of this, each standard requires a different minimum separation distance between the module and human body.
PAGE 44
MGM220P Wireless Gecko Bluetooth Module Data Sheet Certifications 11.6 Japan - MIC The MGM220P22A are certified in Japan with certification number 020-200012. It is the end-product manufacturer's responsibility to ensure that the module is configured to meet the limits documented in the formal certification test report available at https://www.silabs.com/. If needed, refer to the API reference manual(s) to learn how to configure the maximum RF TX power for the normal operations.
PAGE 45
MGM220P Wireless Gecko Bluetooth Module Data Sheet Certifications 11.7 South Korea - KC The MGM220P22A modules have a RF certification for import and use in South-Korea. Certification number is: R-R-BGT-GM220P When integrating the RF-certified module, an end-product is exempted from doing the RF emission testing, as long as the recommended design guidance is followed, and the approved antennas are used. EMC testing, and any other relevant test, might still be required for full compliance. 11.
PAGE 46
MGM220P Wireless Gecko Bluetooth Module Data Sheet Revision History 12. Revision History Revision 0.5 March, 2020 Initial release. tia en fid on C l silabs.com | Building a more connected world. Preliminary Rev. 0.
PAGE 47
Simplicity Studio One-click access to MCU and wireless tools, documentation, software, source code libraries & more. Available for Windows, Mac and Linux! IoT Portfolio www.silabs.com/IoT SW/HW Quality Support and Community www.silabs.com/simplicity www.silabs.com/quality community.silabs.