Data Sheet
Table Of Contents
- 1. Features
- 2. Ordering Information
- 3. System Overview
- 4. Electrical Specifications
- 4.1 Absolute Maximum Ratings
- 4.2 General Operating Conditions
- 4.3 MCU Current Consumption at 3.0V
- 4.4 Radio Current Consumption at 3.0V
- 4.5 RF Transmitter General Characteristics
- 4.6 RF Receiver General Characteristics
- 4.7 RF Receiver Characteristics for Bluetooth Low Energy at 1 Mbps
- 4.8 RF Receiver Characteristics for Bluetooth Low Energy at 2 Mbps
- 4.9 RF Receiver Characteristics for Bluetooth Low Energy at 500 kbps
- 4.10 RF Receiver Characteristics for Bluetooth Low Energy at 125 kbps
- 4.11 High-Frequency Crystal
- 4.12 GPIO Pins
- 4.13 Microcontroller Peripherals
- 4.14 Typical Performance Curves
- 5. Reference Diagrams
- 6. Pin Definitions
- 7. Design Guidelines
- 8. Package Specifications
- 9. Soldering Recommendations
- 10. Tape and Reel
- 11. Certifications
- 12. Revision History
4.4 Radio Current Consumption at 3.0V
RF current consumption measured with MCU in EM1, HCLK = 38.4 MHz, and all MCU peripherals disabled. Unless otherwise indica-
ted, typical conditions are: VDD = 3.0V. T
A
= 25 °C. Minimum and maximum values in this table represent the worst conditions across
process variation at T
A
= 25 °C.
Table 4.4. Radio Current Consumption at 3.0V
Parameter Symbol Test Condition Min Typ Max Unit
Current consumption in re-
ceive mode, active packet
reception
I
RX_ACTIVE
125 kbit/s, 2GFSK, f = 2.4 GHz,
Bluetooth stack running
— 9.3 — mA
500 kbit/s, 2GFSK, f = 2.4 GHz,
Bluetooth stack running
— 9.3 — mA
1 Mbit/s, 2GFSK, f = 2.4 GHz,
Bluetooth stack running
— 9.3 — mA
2 Mbit/s, 2GFSK, f = 2.4 GHz,
Bluetooth stack running
— 9.9 — mA
Current consumption in re-
ceive mode, Stack running
I
RX_LISTEN
125 kbit/s, 2GFSK, f = 2.4 GHz,
Bluetooth stack running
— 9.1 — mA
500 kbit/s, 2GFSK, f = 2.4 GHz,
Bluetooth stack running
— 9.1 — mA
1 Mbit/s, 2GFSK, f = 2.4 GHz,
Bluetooth stack running
— 9.1 — mA
2 Mbit/s, 2GFSK, f = 2.4 GHz,
Bluetooh stack running
— 9.8 — mA
Current consumption in
transmit mode
I
TX
f = 2.4 GHz, CW, 10 dBm Module,
0 dBm output power
— 16.1 — mA
f = 2.4 GHz, CW, 10 dBm Module,
10 dBm output power
— 34.1 — mA
f = 2.4 GHz, CW, 20 dBm Module,
10 dBm output power, VDD = 3.0
V
— 59.7 — mA
f = 2.4 GHz, CW, 20 dBm Module,
P
OUT
=19.2 dBm, VDD = 3.3 V
1
— 173 — mA
Note:
1. The maximum power for Bluetooth Low-Energy is limited to 19.2 dBm.
BGM210P Blue Gecko Bluetooth Module Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 0.5 | 10