User's Guide

ManualsBrandsSilicon Laboratories Finland ManualsElectronicsWT41 long range Bluetooth 2.1+EDR module

Linde Bluetooth USB Stick User Guide

Introduction

Issued on 13. September 2018 by Florian Baumgartl

Revision 1.0

Revision History

Version

Date

Notes

Author

1.0

20.08.2018

(IR) Initial Release

Pascal Hönisch

1. Introduction

This document describes the first steps to bring your Linde Bluetooth USB into operation.

Please feel free to contact us under support@m2mgermany.de if you need any further

information.

1.1. Functional Principle

The Linde Bluetooth USB Stick is recognized as a standard USB serial device by your

operating system. Microsoft Windows will add a new COM port and Linux-based systems will

show the device as /dev/ttyUSB*. Thanks to the integrated Bluegiga iWRAP firmware you do

not depend on the Bluetooth stack of your OS. Instead you can communicate to your

Bluetooth devices directly over this virtual serial port.

Summary of content (6 pages)

PAGE 1
Linde Bluetooth USB Stick User Guide Introduction Revision History Version 1.0 Date 20.08.2018 Notes (IR) Initial Release Author Pascal Hönisch 1. Introduction This document describes the first steps to bring your Linde Bluetooth USB into operation. Please feel free to contact us under support@m2mgermany.de if you need any further information. 1.1. Functional Principle The Linde Bluetooth USB Stick is recognized as a standard USB serial device by your operating system.
PAGE 2
Linde Bluetooth USB Stick User Guide Preparations 2. Preparations 1.2. Windows Driver(s) By default Windows will recognize the Linde Bluetooth USB Stick as Silicon Labs CP210x USB to UART Bridge. Please make sure to use the latest driver version which can be found under https://www.silabs.com/products/development-tools/software/usb-to-uart-bridgevcp-drivers. 1.3.
PAGE 3
Linde Bluetooth USB Stick User Guide Getting Started 1.4. OEM Driver(s) options: For special driver changes like OEM versions, please consult the website of the chip manufacturer Silicon Labs. 3. Getting Started 1.5. iWRAP Commands Once the serial port is available in your system, you can connect the Linde Bluetooth USB Stick to it with a terminal program. Use the settings 115200@8N1 with RTS/CTS hardware flow control enabled.
PAGE 4
Linde Bluetooth USB Stick User Guide Getting Started The INQUIRY command for example lists all visible Bluetooth devices in range: INQUIRY 8 NAME INQUIRY_PARTIAL **:**:**:3e:13:59 INQUIRY_PARTIAL **:**:**:bd:70:19 INQUIRY_PARTIAL **:**:**:0a:d9:bc INQUIRY_PARTIAL **:**:**:53:85:77 INQUIRY_PARTIAL **:**:**:cb:68:c2 INQUIRY_PARTIAL **:**:**:4a:a3:15 INQUIRY_PARTIAL **:**:**:66:37:f5 INQUIRY_PARTIAL **:**:**:57:da:60 INQUIRY 8 INQUIRY **:**:**:3e:13:59 380104 INQUIRY **:**:**:bd:70:19 0a010c INQUIRY **:**:**
PAGE 5
Linde Bluetooth USB Stick User Guide Declaration of Conformity 4. Declaration of Conformity Hereby, m2m Germany GmbH, declares that this BT Audio Adapter is in compliance with the essential requirements and other relevant provisions of the following Directives: Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity.
PAGE 6
Linde Bluetooth USB Stick User Guide Trademarks This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.