User Manual
Table Of Contents
- Access Server
- Table of Contents
- List of Tables
- Chapter 1. Introduction to Access Server
- Chapter 2. Getting Started with Access Server
- Chapter 3. Using the System
- 3.1. Network Interfaces
- 3.2. Bluetooth
- 3.3. Compact Flash Cards
- 3.4. USB Memory Dongles and Compact Flash Memory Cards
- 3.5. Servers
- 3.5.1. Finder
- 3.5.2. ObexSender
- 3.5.3. SMS Gateway Server
- 3.5.4. User Level Watchdog
- 3.5.5. Remote Management
- 3.5.5.1. Overview
- 3.5.5.2. Management Packet Format
- 3.5.5.3. Management Packet Information File Format
- 3.5.5.4. Management Operation Example: Hello World
- 3.5.5.5. Management Operation Example: Software Update
- 3.5.5.6. Management Operation Example: IPQUERY
- 3.5.5.7. Management with USB Memory Dongle or Compact Flash Memory Card
- 3.5.6. FTP
- 3.5.7. Web Server
- 3.5.8. SNMP
- 3.5.9. OpenVPN
- 3.5.10. SSH
- 3.5.11. Telnet
- 3.5.12. NTP
- 3.6. Utilities
- 3.7. Real Time Clock
- 3.8. Time Zone
- 3.9. System ReInstall and Upgrade
- Chapter 4. SPPoverIP
- Chapter 5. Obexsender
- Chapter 6. Software Development Kit
- 6.1. Introduction to SDK
- 6.2. Installing SDK
- 6.3. Creating Applications
- Chapter 7. iWRAP Bluetooth Interface
- 7.1. Terms
- 7.2. Starting the iWRAP Servers
- 7.3. Writing iWRAP Applications
- 7.4. Commands Controlling iWRAP
- INFO
- QUIT
- SET
- SAVE
- LOAD
- PING
- PONG
- ECHO
- LOCK
- UNLOCK
- SHUTDOWN
- SLEEP
- 7.5. Finding Bluetooth Devices
- INQUIRY
- NAME
- 7.6. Making a Bluetooth Connection
- CALL
- CONNECT
- NO CARRIER
- RING
- RINGING
- CLOSE
- LIST
- STATUS
- 7.7. Service Discovery
- SDPSEARCH
- SDPATTR
- SDPQUERY
- SDP bdaddr
- SDP ADD
- SDP DEL
- SDP LIST
- 7.8. Example Sessions
- 7.9. Error Codes
- Chapter 8. I/O API
- Chapter 9. Advanced Use Cases for Access Server
- Chapter 10. Certification Information and WEEE Compliance
- Appendix A. Directory Structure
- Appendix B. Setup Options
- Appendix C. Open Source Software Licenses
- Appendix D. Supported Hardware
Chapter 5. Obexsender
Figure 5-3. Obexsender Use Case: Content Pull
5.3. Configuration
This chapter contains instructions from the most basic Obexsender configuration to the more
advanced use cases.
5.3.1. Getting Started
The easiest and fastest way to configure Obexsender is through the WWW setup. To do this,
your Access Server must be connected to the same network as your PC or, alternatively, you
can also use a direct Ethernet cross cable or a Bluetooth PAN connection (see Section 3.2.5 for
instructions on how to enable PAN). By default, Access Server uses DHCP, so if you connect it
to your LAN, it must support DHCP as well.
1. Once you have successfully connected Access Server, start the "WRAPFinder" software.
WRAPFinder lists all the Access servers in the same network as your PC.
If Access Server does not show immediately, you may need to push the Rescan button a
couple of times.
49