User Manual
Table Of Contents
- Access Server
- Table of Contents
- List of Tables
- Chapter 1. Introduction to Access Server
- Chapter 2. Getting Started with Access Server
- Chapter 3. Using the System
- 3.1. Network Interfaces
- 3.2. Bluetooth
- 3.3. Compact Flash Cards
- 3.4. USB Memory Dongles and Compact Flash Memory Cards
- 3.5. Servers
- 3.5.1. Finder
- 3.5.2. ObexSender
- 3.5.3. SMS Gateway Server
- 3.5.4. User Level Watchdog
- 3.5.5. Remote Management
- 3.5.5.1. Overview
- 3.5.5.2. Management Packet Format
- 3.5.5.3. Management Packet Information File Format
- 3.5.5.4. Management Operation Example: Hello World
- 3.5.5.5. Management Operation Example: Software Update
- 3.5.5.6. Management Operation Example: IPQUERY
- 3.5.5.7. Management with USB Memory Dongle or Compact Flash Memory Card
- 3.5.6. FTP
- 3.5.7. Web Server
- 3.5.8. SNMP
- 3.5.9. OpenVPN
- 3.5.10. SSH
- 3.5.11. Telnet
- 3.5.12. NTP
- 3.6. Utilities
- 3.7. Real Time Clock
- 3.8. Time Zone
- 3.9. System ReInstall and Upgrade
- Chapter 4. SPPoverIP
- Chapter 5. Obexsender
- Chapter 6. Software Development Kit
- 6.1. Introduction to SDK
- 6.2. Installing SDK
- 6.3. Creating Applications
- Chapter 7. iWRAP Bluetooth Interface
- 7.1. Terms
- 7.2. Starting the iWRAP Servers
- 7.3. Writing iWRAP Applications
- 7.4. Commands Controlling iWRAP
- INFO
- QUIT
- SET
- SAVE
- LOAD
- PING
- PONG
- ECHO
- LOCK
- UNLOCK
- SHUTDOWN
- SLEEP
- 7.5. Finding Bluetooth Devices
- INQUIRY
- NAME
- 7.6. Making a Bluetooth Connection
- CALL
- CONNECT
- NO CARRIER
- RING
- RINGING
- CLOSE
- LIST
- STATUS
- 7.7. Service Discovery
- SDPSEARCH
- SDPATTR
- SDPQUERY
- SDP bdaddr
- SDP ADD
- SDP DEL
- SDP LIST
- 7.8. Example Sessions
- 7.9. Error Codes
- Chapter 8. I/O API
- Chapter 9. Advanced Use Cases for Access Server
- Chapter 10. Certification Information and WEEE Compliance
- Appendix A. Directory Structure
- Appendix B. Setup Options
- Appendix C. Open Source Software Licenses
- Appendix D. Supported Hardware
Chapter 4. SPP-over-IP
You must replace the Bluetooth address used in the example (00:07:80:80:bf:01) with the Blue-
tooth address of the Access Server, on which you want to receive the PAN connection.
Note: The server receiving the PAN connection must have the PAN-NAP profile enabled. This is by
default not the case, so in setup or its WWW interface, ensure that the setting at −→ Bluetooth settings
−→ Bluetooth profiles −→ Enable PAN network access point profile says yes. No other configuration
is needed. See
Section 3.2.5 for more information on PAN profiles.
The Bluetooth PIN codes must be the same in both Access Servers.
Figure 4-11. Repeater Configuration
4.2.4. Wi-Fi Configuration
If Access Servers must be connected to Wi-FI (WLAN) instead of physical Ethernet connection,
you also need to make additional configurations through the WWW setup.
See Section 3.3.3 for more information.
4.2.5. GPRS Configuration
If Access Servers must be connected to GPRS network instead of physical Ethernet or Wi-Fi
connection, you also need to make additional configurations through the WWW setup.
See Section 3.3.1 for more information.
46