User Manual
Table Of Contents
- Access Server
- Table of Contents
- List of Tables
- Chapter 1. Introduction to Access Server
- Chapter 2. Getting Started with Access Server
- Chapter 3. Using the System
- 3.1. Network Interfaces
- 3.2. Bluetooth
- 3.3. Compact Flash Cards
- 3.4. USB Memory Dongles and Compact Flash Memory Cards
- 3.5. Servers
- 3.5.1. Finder
- 3.5.2. ObexSender
- 3.5.3. SMS Gateway Server
- 3.5.4. User Level Watchdog
- 3.5.5. Remote Management
- 3.5.5.1. Overview
- 3.5.5.2. Management Packet Format
- 3.5.5.3. Management Packet Information File Format
- 3.5.5.4. Management Operation Example: Hello World
- 3.5.5.5. Management Operation Example: Software Update
- 3.5.5.6. Management Operation Example: IPQUERY
- 3.5.5.7. Management with USB Memory Dongle or Compact Flash Memory Card
- 3.5.6. FTP
- 3.5.7. Web Server
- 3.5.8. SNMP
- 3.5.9. OpenVPN
- 3.5.10. SSH
- 3.5.11. Telnet
- 3.5.12. NTP
- 3.6. Utilities
- 3.7. Real Time Clock
- 3.8. Time Zone
- 3.9. System ReInstall and Upgrade
- Chapter 4. SPPoverIP
- Chapter 5. Obexsender
- Chapter 6. Software Development Kit
- 6.1. Introduction to SDK
- 6.2. Installing SDK
- 6.3. Creating Applications
- Chapter 7. iWRAP Bluetooth Interface
- 7.1. Terms
- 7.2. Starting the iWRAP Servers
- 7.3. Writing iWRAP Applications
- 7.4. Commands Controlling iWRAP
- INFO
- QUIT
- SET
- SAVE
- LOAD
- PING
- PONG
- ECHO
- LOCK
- UNLOCK
- SHUTDOWN
- SLEEP
- 7.5. Finding Bluetooth Devices
- INQUIRY
- NAME
- 7.6. Making a Bluetooth Connection
- CALL
- CONNECT
- NO CARRIER
- RING
- RINGING
- CLOSE
- LIST
- STATUS
- 7.7. Service Discovery
- SDPSEARCH
- SDPATTR
- SDPQUERY
- SDP bdaddr
- SDP ADD
- SDP DEL
- SDP LIST
- 7.8. Example Sessions
- 7.9. Error Codes
- Chapter 8. I/O API
- Chapter 9. Advanced Use Cases for Access Server
- Chapter 10. Certification Information and WEEE Compliance
- Appendix A. Directory Structure
- Appendix B. Setup Options
- Appendix C. Open Source Software Licenses
- Appendix D. Supported Hardware
Chapter 3. Using the System
3.2.1. iWRAP Password Protection
The access to iWRAP can be password protected. The default password is buffy, but it can be
set off or changed with the setup application (see Section 2.4). The password is case sensitive.
The password must be typed in as the first command after the server has replied with "READY."
3.2.2. LAN Access Profile
This profile is not automatically started at boot. The default settings can be changed with the
setup application (see section Section 2.4), or runtime with the iWRAP interface (see Chapter 7).
Access Server can also act as a LAN Access Client, but in this case it must be controlled manually
using iWRAP commands, as described in Chapter 7.
Note: Since Bluetooth specification 1.2, LAN Access Profile has been deprecated.
3.2.3. Serial Port Profile
This profile is not automatically started at boot. The default settings can be changed with the
setup application (see section Section 2.4).
The Serial Port Profile is used to replace an RS-232 serial cable between two devices with a
Bluetooth connection. The physical setup is shown in Figure 3-1.
Figure 3-1. Serial Cable Replacement Physical Setup
State A) in the figure is the starting situation with a serial cable connecting the devices. This
cable is to be replaced with a Bluetooth connection.
In state B) the long serial connection is replaced with a Bluetooth Serial Port Profile connection
between the two Access Server devices. These Access Server devices are then locally connected
20