User Manual
Table Of Contents
- Access Server
- Table of Contents
- List of Tables
- Chapter 1. Introduction to Access Server
- Chapter 2. Getting Started with Access Server
- Chapter 3. Using the System
- 3.1. Network Interfaces
- 3.2. Bluetooth
- 3.3. Compact Flash Cards
- 3.4. USB Memory Dongles and Compact Flash Memory Cards
- 3.5. Servers
- 3.5.1. Finder
- 3.5.2. ObexSender
- 3.5.3. SMS Gateway Server
- 3.5.4. User Level Watchdog
- 3.5.5. Remote Management
- 3.5.5.1. Overview
- 3.5.5.2. Management Packet Format
- 3.5.5.3. Management Packet Information File Format
- 3.5.5.4. Management Operation Example: Hello World
- 3.5.5.5. Management Operation Example: Software Update
- 3.5.5.6. Management Operation Example: IPQUERY
- 3.5.5.7. Management with USB Memory Dongle or Compact Flash Memory Card
- 3.5.6. FTP
- 3.5.7. Web Server
- 3.5.8. SNMP
- 3.5.9. OpenVPN
- 3.5.10. SSH
- 3.5.11. Telnet
- 3.5.12. NTP
- 3.6. Utilities
- 3.7. Real Time Clock
- 3.8. Time Zone
- 3.9. System ReInstall and Upgrade
- Chapter 4. SPPoverIP
- Chapter 5. Obexsender
- Chapter 6. Software Development Kit
- 6.1. Introduction to SDK
- 6.2. Installing SDK
- 6.3. Creating Applications
- Chapter 7. iWRAP Bluetooth Interface
- 7.1. Terms
- 7.2. Starting the iWRAP Servers
- 7.3. Writing iWRAP Applications
- 7.4. Commands Controlling iWRAP
- INFO
- QUIT
- SET
- SAVE
- LOAD
- PING
- PONG
- ECHO
- LOCK
- UNLOCK
- SHUTDOWN
- SLEEP
- 7.5. Finding Bluetooth Devices
- INQUIRY
- NAME
- 7.6. Making a Bluetooth Connection
- CALL
- CONNECT
- NO CARRIER
- RING
- RINGING
- CLOSE
- LIST
- STATUS
- 7.7. Service Discovery
- SDPSEARCH
- SDPATTR
- SDPQUERY
- SDP bdaddr
- SDP ADD
- SDP DEL
- SDP LIST
- 7.8. Example Sessions
- 7.9. Error Codes
- Chapter 8. I/O API
- Chapter 9. Advanced Use Cases for Access Server
- Chapter 10. Certification Information and WEEE Compliance
- Appendix A. Directory Structure
- Appendix B. Setup Options
- Appendix C. Open Source Software Licenses
- Appendix D. Supported Hardware
Chapter 2. Getting Started with Access Server
Access Server can be controlled in three ways:
• by using the WWW interface
• by entering commands and using applications at the Access Server shell prompt
• by sending and/or retrieving files to/from Access Server.
Note: The default username is root and the default password is buffy.
2.1. Powering Up
To get started with Access Server, connect it to your local area network (LAN) by using an
Ethernet cable, and connect the power adapter. Access Server will power up and retrieve the
network settings from your network’s DHCP server.
Access Server will also use Zeroconf (also known as Zero Configuration Networking or Au-
tomatic Private IP Addressing) to get an unique IP address in the 169.254.x.x network. Most
operating systems also support this. In other words, you can connect your controlling laptop
with a cross-over Ethernet cable to Access Server, then power up Access Server, and the devices
will automatically have unique IP addresses in the 169.254.x.x network.
Note: If you need to configure the network settings manually and cannot connect first by using Zero-
conf, you can do it by using the management console. For more information, see Section 2.3.1.
The physical interface locations of Access Server are described in Figure 2-1 and Figure 2-2.
Figure 2-1. Access Server Connectors
Note: There is no power switch in Access Server. The adapter is the disconnection device; the socket-
outlet shall be installed near the equipment and shall be easily accessible. Unplug and plug the power
adapter to switch the power on and off. The power led in
Figure 2-2 is on when the power adapter is
connected.
3