User's Manual
Table Of Contents
- 1. Feature List
- 2. Ordering Information
- 3. System Overview
- 4. Electrical Specifications
- 4.1 Electrical Characteristics
- 4.1.1 Absolute Maximum Ratings
- 4.1.2 Operating Conditions
- 4.1.3 Current Consumption
- 4.1.4 Wake up times
- 4.1.5 Brown Out Detector
- 4.1.6 Frequency Synthesizer Characteristics
- 4.1.7 2.4 GHz RF Transceiver Characteristics
- 4.1.8 Oscillators
- 4.1.9 Flash Memory Characteristics
- 4.1.10 GPIO
- 4.1.11 VMON
- 4.1.12 ADC
- 4.1.13 IDAC
- 4.1.14 Analog Comparator (ACMP)
- 4.1.15 I2C
- 4.1.16 USART SPI
- 4.2 Typical Performance Curves
- 4.1 Electrical Characteristics
- 5. Typical Connection Diagrams
- 6. Layout Guidelines
- 7. Pin Definitions
- 8. BGM113 Package Specifications
- 9. Certifications
- 10. Revision History
- Table of Contents
1. Feature List
The BGM113 highlighted features are listed below.
• Low Power Wireless System-on-Chip.
•
High Performance 32-bit 38.4 MHz ARM Cortex
®
-M4 with
DSP instruction and floating-point unit for efficient signal
processing
•
256 kB flash program memory
• 32 kB RAM data memory
• 2.4 GHz radio operation
• TX power up to +3 dBm
• Low Energy Consumption
• 8.7 mA RX current at 2.4 GHz
• 8.8 mA TX current @ 0 dBm output power at 2.4 GHz
• 63 μA/MHz in Active Mode (EM0)
• 1.4 μA EM2 DeepSleep current (full RAM retention and
RTCC running from LFXO)
• 1.1 μA EM3 Stop current (State/RAM retention)
• Wake on Radio with signal strength detection, preamble
pattern detection, frame detection and timeout
• High Receiver Performance
• -93 dBm sensitivity @ 1 Mbit/s GFSK (2.4GHz)
• Supported Protocol
•
Bluetooth
®
Smart
• Support for Internet Security
• General Purpose CRC
• Random Number Generator
• Hardware Cryptographic Acceleration for AES 128/256,
SHA-1, SHA-2 (SHA-224 and SHA-256) and ECC
• Wide selection of MCU peripherals
•
12-bit 1 Msps SAR Analog to Digital Converter (ADC)
• 2× Analog Comparator (ACMP)
• Digital to Analog Current Converter (IDAC)
• 14 pins connected to analog channels (APORT) shared be-
tween Analog Comparators, ADC, and IDAC
• 14 General Purpose I/O pins with output state retention and
asynchronous interrupts
• 8 Channel DMA Controller
• 12 Channel Peripheral Reflex System (PRS)
• 2×16-bit Timer/Counter
• 3 + 4 Compare/Capture/PWM channels
• 32-bit Real Time Counter and Calendar
• 16-bit Low Energy Timer for waveform generation
• 32-bit Ultra Low Energy Timer/Counter for periodic wake-up
from any Energy Mode
• 16-bit Pulse Counter with asynchronous operation
• Watchdog Timer with dedicated RC oscillator @ 50nA
• 2×Universal Synchronous/Asynchronous Receiver/Trans-
mitter (UART/SPI/SmartCard (ISO 7816)/IrDA/I
2
S)
•
Low Energy UART (LEUART
™
)
•
I
2
C interface with SMBus support and address recognition
in EM3 Stop
• Wide Operating Range
• 1.85 V to 3.8 V single power supply
• Integrated DC-DC
• -40 °C to 85 °C
• Dimensions
• 9.15 x 15.73 x 1.9 mm
BGM113 Blue Gecko Bluetooth
®
Smart Module
Data Sheet
Feature List
silabs.com | Smart. Connected. Energy-friendly. Preliminary Rev. 0.93 | 1