User Manual

ManualsBrandsSIIG ManualsComputers & AccessoriesDual Profile PCI Express 2-port SATA II Controller Card

DP SATA II PCIe

Installation Guide

04-0936A

Introduction

The DP SATA II PCIe is designed to add two Serial ATA

channels for connecting up to two hard disk drives to

your PCIe equipped system.

Features and Benefits

• Compliant with PCI Express Base Specification

Revision 1.0a

• Compliant with Serial ATA 1.0a specification with

support for full complement of SATA II optional

features

• PCI Express 1-lane (x1) SATA II adapter works with

PCI Express slots with different lane width

• Installs in any available PCI Express slot and

supports data transfer rates up to 3.0Gbps (300MBps)

• Spare enhanced low profile bracket is included to

work in low profile chassis

• Supports Native Command Queuing (NCQ), Non-

zero offsets NCQ, and Out-of-order data delivery

NCQ

• Independent command fetch, scatter/gather, and

command execution

System Requirements

• PCI Express-enabled system with an available PCI

Express slot

• Windows

8 (32-/64-bit) / 7 (32-/64-bit) / Vista (32-

/64-bit) / XP (32-/64-bit) / 2000 / Server 2003 &

2008 (32-/64-bit) / Server 2008 R2 / Server 2012

Summary of content (16 pages)

PAGE 1
DP SATA II PCIe Installation Guide Introduction The DP SATA II PCIe is designed to add two Serial ATA channels for connecting up to two hard disk drives to your PCIe equipped system. Features and Benefits • • • • • • • Compliant with PCI Express Base Specification Revision 1.0a Compliant with Serial ATA 1.
PAGE 2
Package Contents • • • • DP SATA II PCIe adapter Spare enhanced low profile bracket SATA data cable Driver CD and installation guide Layout Serial ATA Connector Figure 1: DP SATA II PCIe Board Layout Hardware Installation Note: For low-profile systems, replace the currently mounted bracket with the included low profile bracket. General instructions for installing the card are provided below.
PAGE 3
1. 2. 3. 4. 5. Turn OFF the power to your computer and any other connected peripheral devices. Unplug the power cord from the computer. Remove the computer cover. Remove the slot bracket from an available PCIe slot. To install the card, carefully align the card's bus connector with the selected PCIe slot on the motherboard. Push the board down firmly, but gently, until it is well seated. Replace the slot bracket holding screw to secure the card.
PAGE 4
. Attach the other end of the SATA data cable to the Serial ATA connector on the DP SATA II PCIe. Figure 3. Connecting SATA data cable 5. 6. Follow the same instructions when connecting a second hard disk drive. Device connection is now complete. Replace the computer cover and reconnect the power cord. Driver Installation This section provides information for how to install the DP SATA II PCIe drivers.
PAGE 5
4. 5. 6. 7. 8. 9. Double click folder Win8 located on the driver CD or your Flash Drive. For 32-bit: Click 32bit, then click OK. For 64-bit: Double click 64bit, click AMD64, then click OK. Select Silicon Image SiI 3132...Controller, then click Next. Check I accept the license terms, click Next. Select Custom...(advanced), then click Next. Click OK to continue. Skip this step if not prompted. Wait several seconds, then follow the on-screen instructions to complete Windows installation.
PAGE 6
Windows 7 (32-/64-bit) / Server 2008 R2 New Windows 7 (32-/64-bit) / Server 2008 R2 Installation If you don't have two CD-ROM players, copy the contents of Win7 folder in the driver CD to your Flash Drive, then follow the directions below: 1. 2. 3. 4. 5. 6. 7. 8. 9. Install the board and follow Microsoft procedures to install Windows accordingly. At Install Windows or Windows Setup, click Next, then click Install now. Click Browse. Double click folder Win7 located on the driver CD or your Flash Drive.
PAGE 7
5. 6. 7. Click Browse my computer for driver software. For Windows 7 32-bit: Type D:\Win7\32bit, click OK. For Windows 7 64-bit / Server 2008 R2: Type D:\Win7\64bit\AMD64 (Change D: to match your CD/DVD-ROM drive letter) Click Next, and click Close. Server 2012 New Server 2012 Installation If you don't have two CD-ROM players, copy the contents of Win7 folder in the driver CD to your Flash Drive, then follow the directions below: 1. 2. 3. 4. 5. 6. 7. 8. 9.
PAGE 8
Existing Server 2012 Installation 1. Install the board and boot up Windows. 2. Insert the driver CD. Close the AutoPlay box if prompted. 3. Click Windows key. Right click Computer, Properties, Device Manager. 4. Right click Serial ATA Controller under Other devices, click Update Driver Software. 5. Click Browse my computer for driver software. 6. Type D:\Win7\64bit\AMD64, click Next. (Change D: to match your CD/DVD-ROM drive letter) 7. Click Close.
PAGE 9
5. 6. 7. 8. 9. Select Silicon Image SiI 3132 ... Controller, click Next. Check I accept the license terms, click Next. Select Custom...(advanced), then click Next. Click OK to continue. Skip this step if not prompted. Wait several seconds, then follow the on-screen instructions to complete Windows installation. Existing Windows Vista (32-/64-bit) / Server 2008 (32-/64bit) Installation 1. Install the board and boot up Windows. 2. At the Found New Hardware, click Cancel. 3.
PAGE 10
3. 4. 5. Insert the driver floppy disk you made above. Press S, then press Enter. Select Silicon Image SiI 3132 ... Controller for Windows XP and Server 2003, then press Enter. Press Enter again and follow the on-screen instructions to complete the installation. New Windows XP (64-bit) / 2003 (64-bit) Installation A floppy disk for the driver installation is required. Copy the contents of the 64bit folder in the driver CD to your blank floppy disk.Then follow the directions below: 1. 2. 3. 4. 5.
PAGE 11
5. For 64-bit: Type D:\64bit\AMD64 (Change D: to match your CD/DVD-ROM drive letter) Click Next, and click Finish to complete the installation. Windows 2000 New Windows 2000 Installation A floppy disk for the driver installation is required. Copy the contents of Floppy folder in the driver CD to your blank floppy disk. Then follow the directions below: 1. 2. 3. 4. 5. Install the board and follow Microsoft procedures to install Windows 2000 accordingly. At the Windows 2000 Setup screen, press F6.
PAGE 12
To Verify Windows Installation 1. 2. 12 Use Device Manager to verify installation. For Windows 8 / 7 / XP / Server 2003 / 2000: Right click Computer or My Computer, click Manage, click Device Manager. For Windows Vista: Right click Computer, click Manage, click Continue. Click Device Manager. For Windows Server 2012: Click Windows key. Right click Computer, Properties, click Device Manager. For Windows Server 2008 / 2008 R2: Right click Computer, Manage. Double click Diagnostics, click Device Manager.
PAGE 13
Blank Page 13
PAGE 14
Blank Page 14
PAGE 15
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analyst will promptly respond. SIIG offers a 5-year manufacturer warranty with this product.
PAGE 16
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio.