Installation guide

ManualsBrandsSIIG Manualscomputer componentsLow Profile PCI-2S

PCI I/O-2S/4S

Quick Installation Guide

04-0206A

Introducing the PCI I/O-2S/4S

The Low Profile PCI -2S and Low Profile PCI -4S conform to the new PCI

card form factor standard made for space constrained system designs.

This installation guide is written for both, Low Profile PCI -2S

and Low Profile PCI -4S boards.

Features and Benefits

• Conforms to PCI v2.2 Plug and Play

• Full support for DOS- and Windows-based software

• IRQ sharing feature eliminates IRQ conflicts

• High-speed 16550 UART serial port (9-pin) supports baud rates

up to 920Kbps. Works with various types of serial devices

• Built-in 16-byte FIFO buffers dramatically increase data transmit/

receive speed

• Fan-out cable is provided for multiple serial ports, using only one

PCI slot

Dimensions:

• PCB: 119.91 mm (L) x 64.41 mm (H)

• Bracket: 18.42 mm (W) x 79.20 mm (H)

System Requirements

• Pentium or equivalent computer with an available 32-bit PCI slot

• DOS/Windows 3.1x, Windows 95/98/98 SE/ME/NT 4.0/2000

Summary of content (8 pages)

PAGE 1
PCI I/O-2S/4S Quick Installation Guide Introducing the PCI I/O-2S/4S The Low Profile PCI -2S and Low Profile PCI -4S conform to the new PCI card form factor standard made for space constrained system designs. This installation guide is written for both, Low Profile PCI -2S and Low Profile PCI -4S boards. Features and Benefits • • • • Conforms to PCI v2.
PAGE 2
Package Contents • • • • One Low Profile PCI -2S or Low Profile PCI -4S board One Driver Installation diskette One 5-year warranty card This quick installation guide Hardware Installation General instructions for installing the card are provided below, since the design of computer cases and motherboards vary. Refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system.
PAGE 3
. From the Insert Disk window, click OK. When the Copying Files dialog box appears, type in a:\Win95, then click OK. 4. Remove the diskette and select Yes to restart the computer for the setup to take effect. Windows 98/98 SE: 1. At the Add New Hardware Wizard windows, click Next. 2. Select Search for the best driver for your devices (Recommend), then click Next. 3. Select Specify a location, insert the Driver Installation diskette and type in a:\Win98, then clickNext. 4. Click Next, then Finish. 5.
PAGE 4
. From Choose Destination Location window, click Next. 5. Remove the Driver Installation diskette, select Yes to restart Windows and click Finish. To verify successful installation in Windows NT 4.0: 1. Go to Start / Setting / Control Panel, double click SIIG Cyber PCI 20X device icon. 2. New COM port address number will be assigned for the ports when successfully installed. The board is ready to connect devices. To change the I/O address in Windows NT 4.0: 1.
PAGE 5
DOS/Windows 3.1x: 1. Insert the Driver Installation diskette, from the C: prompt, type in copy a:\dos\*.*, then press . 2. Type in edit autoexec.bat, then press . 3. Add C:\CB20XPC.exe at the bottom of the autoexec.bat file. 4. Go to File, save the changes and exit. 5. Remove the diskette and restart the system for the new setup to take effect.
PAGE 6
Troubleshooting Problem: I am installing a parallel port(s) and my system freezes up when Windows tries to install the driver for my printer port. Solution: Enter your system bios, set the onboard parallel port I/O address to 278h, save and exit. In certain systems, the address 278h is reserved for ISA boards. So when the PCI parallel port tries to capture this address, your system gets confused and freezes up.
PAGE 7
Technical Support QUESTIONS? SIIG’s Online Support has the answers! Simply visit our web site at www.siig.com and click on ONLINE SUPPORT. Our online support database is updated daily with new drivers and solutions. The answers to your problems could be just a few clicks away. Return Merchandise Authorization (RMA) SIIG warrants to the original buyer of the product that the hardware is free of defects in materials and workmanship for a period of one, two or five years from the date of purchase.
PAGE 8
PRODUCT NAME Low Profile PCI 2S Low Profile PCI 4S MODEL NUMBER LP0408 LP0406 FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.