Installation guide

ManualsBrandsSIIG Manualscomputer componentsHi-Speed USB Dual-Port PCI

USB 2.0 PCI

Quick Installation Guide

04-0293A

Introducing the USB 2.0 PCI

The USB 2.0 PCI adds high-speed USB 2.0 interface to your system.

It supports high-speed (480 Mbps), full-speed (12 Mbps), and low-

speed (1.5 Mbps) data transfer modes. With USB 1.1 backward

support, this host adapter works with various types of USB 2.0/1.1

devices including hubs, digital cameras, PC video cameras, scanners,

joysticks and more.

Note: USB 1.1 devices are limited to USB 1.1 speeds even when

they are connected to USB 2.0 host adapter or USB 2.0 hubs.

Features and Benefits

• Compliant with USB specifications revision 2.0

• Conforms to PCI Specifications

• Supports simultaneous operation of multiple high-speed USB

2.0 and USB 1.1 devices

• Users friendly hot-swapping feature allows you to attach/

remove USB devices without turning your system off

• Supports 480 Mbps, 12 Mbps and 1.5 Mbps data transfer

modes

• Works with a variety of USB2.0/USB 1.1 devices including

hubs, data storage devices, PC video cameras, digital cameras,

CD-R/RWs, DVD-ROMs, scanners, printers, memory card

readers (CF/SM/SD/MMC/Memory Stick), and more...

System Requirements

• Pentium-class computer with an available PCI slot

• Windows 98SE/ME/2000/XP

Package Contents

• One USB 2.0 PCI

• Driver diskette

• This quick installation guide

Summary of content (8 pages)

PAGE 1
USB 2.0 PCI Quick Installation Guide Introducing the USB 2.0 PCI The USB 2.0 PCI adds high-speed USB 2.0 interface to your system. It supports high-speed (480 Mbps), full-speed (12 Mbps), and lowspeed (1.5 Mbps) data transfer modes. With USB 1.1 backward support, this host adapter works with various types of USB 2.0/1.1 devices including hubs, digital cameras, PC video cameras, scanners, joysticks and more. Note: USB 1.1 devices are limited to USB 1.1 speeds even when they are connected to USB 2.
PAGE 2
Hardware Installation General instructions for installing the card are provided below. Refer to your computer’s reference manual for further information, if needed. 1. Turn OFF the power to your computer. 2. Unplug the power cord and remove your computer's cover. 3. Remove the slot bracket from an available PCI slot. 4. Carefully align the card to the selected PCI slot and push the board down firmly, but gently, until it is well seated. 5. Replace the slot bracket's holding screw to secure the card. 6.
PAGE 3
Windows 98SE Driver Installation 1. After installing the board, boot up to Windows. At the Add New Hardware Wizard, click Cancel three times. 2. Click Start, Run, insert the driver diskette, type A:\setup206.exe, then click OK. Give it a few seconds for driver installation to complete. 3. Remove the driver diskette, then click Close to restart. 4. When Windows restarts, a USB 1.1 host is detected. 5. At the Add New Hardware Wizard, click Next. 6.
PAGE 4
5. The board is now ready for use. Windows XP Driver Installation If you have have XP Service Pack 1 or later installed, Windows will automatically detect and install the correct driver for this board. Otherwise, follow all steps below. 1. After installing the board, boot up to Windows. At the Found New Hardware Wizard, click Cancel. 2. Click Start, Run, insert the driver diskette, type A:\setup206.exe, then click OK. 3. At the Software Installation window click Continue Anyway.
PAGE 5
2. Double click Universal Serial Bus controllers and the following options should be displayed, in addition to others that may come with your system. - NEC ... USB Open Host Controller ... - NEC ... USB Open Host Controller ... - NEC ... USB Enhanced Host Controller - USB 2.0 Root Hub Device - USB Root Hub - USB Root Hub 3. If these options DO NOT appear: a. Look for USB controller(s) under Other Devices with yellow exclaimation marks (!), remove them and restart your system.
PAGE 6
Technical Support QUESTIONS? SIIG’s Online Support has the answers! Simply visit our web site at www.siig.com and click SUPPORT. Our online support database is updated daily with new drivers and solutions. The answers to your problems could be just a few clicks away. Return Merchandise Authorization (RMA) SIIG warrants to the original buyer of the product that the hardware is free of defects in materials and workmanship for a period of one, two or five years from the date of purchase.
PAGE 7
UK Warranty & Support Information The 5 year warranty supplied with this product is offered by SIIG, Inc. If you should happen to encounter any problems with this product, please follow the procedures below. 1. If it is within the first year of purchase, please return product to the outlet you purchased from. 2. If your product is between 2 and 5 years old from date of purchase, please contact SIIG using the contact details below.
PAGE 8
Empty Page