Cyber 2S1P 950 PCI Quick Installation Guide Introducing the Cyber 2S1P 950 PCI The Cyber 2S1P 950 PCI high-speed serial I/O card provides two 9-pin serial ports and one parallel port. Key Features and Benefits • • • Universal PCI card design that works in 32/64-bit 3.
Package Contents • • • • Cyber 2S1P 950 PCI board Connector bracket w/9-pin serial port Driver CD Quick installation guide Layout Serial port 2 JP1 JP2 Power connector Serial port 1 Parallel port Figure 1: Board Layout Jumper Settings (JP1, JP2) Open = 0 volts (default) Short 1-2 = 5V Short 2-3 = 12V 2
Note: Most serial devices do not require additional power through the serial port. Refer to your serial device's manual for more information. Power Connector Connects to the system's power supply. Make this connection when the serial port(s) are configured for 5V or 12V power. Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed.
2. 3. 4. 5. 6. 7. Unplug the power cord from the computer. Remove the computer cover. Remove the slot bracket from an available PCI slot. To install the card, carefully align the card's bus connector with the selected PCI slot on the motherboard. Push the board down firmly, but gently, until it is well seated. Replace the slot bracket holding screw to secure the card. Replace the computer cover and reconnect the power cord.
4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Click Browse my computer for driver software. Type D:, then click Next. (Change D: to match your CD/DVD-ROM drive letter) Click Install this driver software anyway. At Windows has successfully updated your driver software, click Close. Right click PCI Device, click Update Driver Software. Repeat steps 4-7. Right click CyberSerial Communication Port, click Update Driver Software. Repeat steps 4-7. Right click CyberSerial Communication Port, click Update Driver Software.
3. 4. 5. 6. 7. 8. 9. Click Don't search online. Click I don't have the driver disc. Show me other options. Click Browse my computer for driver software (advanced). Type D:, click Next. (Change D: to match your CD/DVD-ROM drive letter) Click Install this driver software anyway. At The sofware for this device has been successfully installed, click Close. Repeat steps 3-8 to complete the installation. Windows XP (32-/64-bit) / Server 2003 (32-/ 64-bit) 1. 2. 3. 4. 6 Install the board and boot up Windows.
5. 6. Click Continue Anyway, then click Finish. Repeat steps 3-5 three times to complete the installation. Windows Server 2008 (32-/64-bit) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Install the board and boot up Windows. At the Found New Hardware Wizard, click Locate and install driver software (recommended). Insert the driver CD. Click Don't search online. Skip this step and go directly to step 5 if not prompted. Click I don't have the disc. Show me other options.
Windows 2000 1. 2. 3. 4. 5. 6. 7. At the Found New Hardware Wizard, click Next. Select Search for a suitable driver for my device (recommended), and click Next. Select Specify a location, uncheck the other boxes, and click Next. Insert the driver CD, type in D:, then click OK. (Change D: to match your CD-ROM drive letter) Click Next and Finish. Repeat steps 1-5. Restart Windows to complete the installation. To Verify Windows 7 / Vista / XP / Server 2003 & 2008 / 2000 Installation 1.
2. 3. For XP / Server 2003 / 2000: Right click My Computer, click Manage, then click Device Manager. For Server 2008: Right click Computer, click Manage, double click Diagnostics, click Device Manager. Click on the + (plus sign) in front of Ports (COM & LPT), CyberSerial 950 16Cxxx... and SIIG CyberPro Parallel Port... should be displayed. Double click Multifunction adapters, SIIG CyberPro 2S1P board should be displayed. Windows ME 1. 2.
3. 4. 5. Click Next and Finish. Repeat steps 1-3. Restart Windows to installation. complete the Windows 98SE / 98 1. 2. 3. 4. 5. 6. At the Add New Hardware Wizard, click Next. Select Search for the best driver for your device (Recommended), then click Next. Select Specify a location, uncheck the other boxes, insert the driver CD, type in D:\9x, then click Next. (Change D: to match your CD-ROM drive letter) Click Next, then Finish. Repeat steps 1-4. Restart Windows to complete the installation.
2. 3. 4. 5. Insert the driver CD, and click Other Locations. Type in D:\9x, click OK, then Finish. (Change D: to match your CDROM drive letter) From the Insert Disk window, click OK. When the Copying Files dialog box appears, type in D:\9x, then click OK. (Change D: to match your CD-ROM drive letter) Repeat steps 1-3. Restart to complete the installation. To Verify Windows ME / 98SE / 98 / 95 Installation 1. 2. 3.
Changing COM Port Address Some serial devices need a specific COM port in order to work. If your serial device works properly, do not change this setting. Windows 7 / Vista / XP / Server 2003 & 2008 / 2000 1. 2. 3. 4. From the Device Manager window double click Ports (COM & LPT), then double click CyberSerial... port. Click Settings tab and click Advanced. Click the down arrow next to the COM Port number box, select a COM port that is not in use. Click OK.
2. 3. Click Settings tab, click the down arrow next to Port Name, select a COM address not currently in use. Click OK, then close Device Manager to save the changes. Changing Parallel Port Address (LPT) Some parallel devices need a specific parallel port in order to work. If your parallel device works properly, do not change this setting. Windows 7 / Vista / XP / Server 2003 & 2008 / 2000 1. 2. 3. 4.
Windows ME / 98SE / 98 / 95 1. 2. 3. 14 From the Device Manager window double click Ports (COM & LPT), then double click CyberParallel. Click Settings tab, check Enable use of I/O location 278h. Click OK, click OK again to close Device Manager, and click Yes to restart Windows to save the changes.
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a lifetime manufacturer warranty with this product.
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio.
