4 Channel 10" LCD DVR Camera Kit Model No QV -3030 USER’S MANUAL
INDEX SAFETY INSTRUCTIONS ............................................................................................................................................ 3 CHAPTER 1: DVR FEATURES .................................................................................................................................... 4 CHAPTER 2:LAYOUT .................................................................................................................................................. 5 2.1 FRONT PANEL ..
5.2.7.1 Time Set ................................................................................................................................................................................ 22 5.2.7.2 Password ............................................................................................................................................................................... 22 5.2.7.3 Video Setup ...................................................................................................
Safety Instructions 1. Use proper power source. Do not use this product with a power source that applies more than specified voltage (100-240V AC). 2. Never insert anything metallic into the DVR case. Putting something into the DVR case can be a source of dangerous electric shock. 3. Do not operate in wet & dusty area or use near water. Avoid places like a damp basement or dusty hallway. 4. Do not expose this product to rain or use near water.
Chapter 1: DVR Features Real time monitoring Supports real time surveillance via Monitor Saves Recordings DVR saves real-time recording image to HDD Backup Recordings Supports DVR backup via USB flash drive and hard drive.
Chapter 2:Layout 2.1 Front Panel Item Number 1 Button Name / Symbol POWER Function On: The LCD screen is displayed in a basic activation status; Off: The LCD screen enters into sleep mode. 2 MENU Press once to display LCD main menu. Press again to exit LCD main menu. 3 UP When pressed while the Main Menu is not displayed, the UP arrow button allows you to scroll through the video feeds transmitted from each camera hooked up to your system.
2.
2.
Chapter 3: DVR Installation 3.1 Hard Drive Installation Caution: NEVER Install or remove the hard drive while the DVR is running! The model has a Hard Disk Drive (HDD) drawer. Please use key provided to open the drawer and insert the HDD as follows: (1) Remove screws and open DVR upper cover carefully; (2) Insert Power Cord and data cable securely into matching ports on hard drive; (3) Put the upper cover back carefully, re-attach screws. 3.
Chapter 4: DVR Boot up 4.1 System Initialization After connecting the power adapter，the system will boot-up and start initializing。 Picture 4-1 4.2 Main Interface Picture 4-2 After finishing system initialization, the system will enter into main interface. Picture 4-2 is the main interface displayed by system, which is showing no video input status. Once there are video inputs, the interface will display live images from the cameras.
the channel (details please refer to Picture 5-1). Picture 5-2 Picture 5-3 5.1 Main Menu Preview Color set Camera Dwell time display Recording Network Search Rec.
5.2 Main Menu Picture 5-4 After clicking right button of mouse, pop-up menu will be displayed on the screen. You can click [main menu] button on pop-up menu to enter into Main menu interface (Shown as Picture 5-4). You can also use the Menu button on the front panel to bring up the window, when using the front panel buttons use the FWD and REW button to move in the menu, and the SEL button to select the icon. You use the ESC button to return to previous window.
2. Press SETUP button to adjust the position of the privacy zones 3. After finishing the position adjustment, press ESC key on front panel or click right button of mouse to exit and return to PRIVACY ZONE page. 4. Press [APPLY] button to save you settings. Picture 5-8 5.2.1.3. Autoseq Setup AUTOSEQ allows system to display every selected channel in full screen by certain dwell time, and auto-switch in sequence.
length for every single continuous recording file (15, 30, 45, 60 minutes). 5.2.2.1. Record Mode There are 2 record modes: ALWAYS & TIME SCHEDULE RECORD. When you select ALWAYS record mode, DVR will execute continuous recording without stop. When you select TIME SCHEDULE RECORD mode, DVR will execute recording according to your schedule. Picture 5-12 5.2.2.2. Record Schedule Setup Select TIME SCHEDULE RECORD, a SCHEDULE button will display. Click it and enter schedule setup interface.
5.2.3 Network Set Enter into [Main Menu Network Set] to proceed network set (Shown as picture 5-15): After selecting network mode - such as DHCP、PPPOE and static allocation and setup web port, you could visit DVR remotely via network. Picture 5-15 When selecting DHCP, DHCP server will allocate DVR IP address automatically. When selecting PPPoE, you need to input user and password provided by ISP supplier and set up web port (details please refer to the below picture 5-16).
5.2.4 Recording Search You can enter search & playback interface by pop-up menu bar or main menu. 5.2.4.1. Search Click [Main menu search] to enter into [Video Search] menu (shown as the below picture 5-20). Play back by exact date & time: Modify the date & time, press PLAYBACK button to play back video which is started from your appointed date & time. Picture 5-21 Picture 5-20 Search All Recorded File: Press SEARCH button, system will search and show you the recorded status.
5.2.4.3. Video Backup 1. Insert your USB device (USB hard disk, USB thumb drive) into the bottom USB port on the rear panel. 2. Select one or more files. 3. Press BACKUP button on the menu. NOTE: Do not remove your USB device during making backup. Note: Backup files will be in H.264 format; you can play them with Net viewer program or Multi player, and convert them to AVI format using the Netviewer program that comes with the DVR, so you can use any player that supports AVI format.
the backup file will be played on the according channel. （3）、The Menu brief on the bottom of multimedia player: recording date for the current backup file shown as right corner; Date: 24H recording time: lie under [Date] menu. Black number button stands for current recording playback is normal recording for the time line. 0~60 Minute recording time quantum: Green part on play processing bar stand for recording length for one hour recording.
After successfully setting the above, when you playback the current channel, you can open the channel’s audio function at the same time as the video 5.2.6 Device Management Options in device management include Hard drive, External Alarm, PTZ control, Mobile Phone Monitoring, and Motion Detection. Picture 5-33 5.2.6.
not external sensors to record on motion detection. BUZZER: Option to turn off the built-in buzzer alarm, or set the buzzer alarm time. OUTPUT: Option to turn on/off external sensor. MD ALARM: Option for buzzer to alarm or not when the motion detection happens I/O ALARM: Option for buzzer to alarm or not when the I/O is tripped happens HDD LOSS: Option for buzzer to alarm or not when there is no HDD installed in the DVR, or the HDD is in abnormal working condition.
SMTP Port: indicates sender port of SMTP server. Generally the SMTP port value is 25, SMTP port of G-mail server is 465. SMTP: indicates server address you use. Sender email: indicates sender’s email address. The email address should be consistent with the server you use. That is to say, when you use email address – aaa@gmail.com, the according server should be smtp.gmail.com. SEND PW: enter the login password of send email. RECV EMAIL: indicates receiver’s email address.
5.2.6.4. PTZ Control You can find the PTZ control menu on the pop-up menu bar and open the PTZ control interface. You can click Z+ & Z- keys to zoom In or out, click F+ & F- keys to control camera focus and click I+ & I- to adjust the focus point. Picture 5-42 Open auto cruise function on PTZ setting menu if you want to setup cruise function, and set up cruise channel, cruise point, total quantity and stop time (by second) etc.
5.2.6.6 Motion Detect Click [Main Device Motion] to enter into the [Motion Detection] menu to setup motion detection recording. The [Motion detection] Menu has three sections, including Channel Status, Sensitivity and Motion area. Channel STATUS: This option allow you enable motion detection on any channel. SENSITIVITY: This option allows you to set sensitivity level of motion detection from 1 to 4 with 4 being the most sensitive.
Difference of USER PASSWORD and ADMIN PASSWORD: Login with USER PASSWORD, you can only operate Search & Playback function, and view the live images. You’re limited to check & change any system settings. Login with ADMIN PASSWORD, you will have the authority to operate all menus. Picture 5-51 5.2.7.2.1. Menu Lock Picture 5-52 Picture 5-53 MENU LOCK menu only displays on the pop-up menu bar when password protection is enabled.
5.2.7.5 Info. Click [Main Menu System Info] to enter into [System Information] menu to view system info, including Device type, Software (firmware) version and MAC address etc. Picture 5-56 5.2.7.6 System Maintenance This option allows you reset the DVR to default settings, update system software (firmware), and config system auto-maintenance. When the auto-maintain function is enabled, you can set system to restart regularly to clear up some temporary storage memory.
Warning! It is strongly recommended to return all Internet Explorer Security to its default settings after the ActiveX Control has been installed. Enabling all ActiveX controls put your computer at risk of being attacked by computer virus. 6.1.2. Connect to DVR To connect to the DVR from a remote computer, you would then open an Internet Explorer browser window and enter the Internet IP of your router that you received by going to www.myipaddress.com.
6.3 Main Interface of Net-viewer and IE Picture 6-3 Log in Net-viewer and show the interface as follows 6.3.1 Menu column (Section 1 on Picture 6-3) 6.3.2 PTZ Control (Numbers 2, 3, 4 on Picture 6-3) 6.3.3 Live Play Control (Numbers 6 through 10 on Picture 6-3) 6.3.1 Menu column (Section 1 on Picture 6-3) Menu column include [Live] menu, [Replay] menu and [Setup] menu and [Logout] menu. 6.3.1.1 Live After Logging-in to system, system will enter into Live display (shown as Picture 6-3). 6.3.1.
F.F. button: fast forward playback recording Slow button: slow playback recording. Next Frame: play frame by frame. 264 TO AVI button: convert file from H.264 format to AVI format The native format of the backup files is H.264, you can convert H.264 format into more familiar AVI format by clicking the key of 264 to AVI. 6.3.1.2.1 Convert 264 file to AVI file The native format of the backup files is H.264, you can convert H.264 format into AVI format by clicking the key of 264 to AVI. 1.
recording parameters (resolution, quality, audio, REC mode and Schedule) remotely via Net-viewer. Picture 6-5 Click the [Schedule] menu to enter into its sub menu (shown as Picture 6-6). Remote setup methods are the same as local DVR setup. Please refer to Section 5.2.2 Record Setup ② Alarm Picture 6-6 Click [Alarm] menu to enter into its sub menu (shown as Picture 6-7).
System allows you setup motion detection settings for each channel of DVR remotely (shown as Picture 6-8) Picture 6-8 ③ PTZ Control Click [PTZ control] to setup PTZ cameras. Remote setup methods are the same as local DVR setup. Please refer to Section 5.2.5.3 (shown as Picture 6-9). ④ Network Picture 6-9 Click [Network] to enter into [Network] menu. Remote setup methods are the same as local DVR setup. Please refer to Section 5.2.3. – Network Set.
turn daylight saving time on/off, etc. ⑥ Host Info Picture 6-11 Click [Host Info.] to enter into the sub menu (shown as Picture 6-12). Here you can check Usage rate of HDD, available recording time, software version and MAC address. 6.3.1.4 Log out Picture 6-12 Log out of the system. 6.3.2 PTZ Control (Numbers 2, 3, 4 on Picture 6-3) Note: below-mentioned series no will be consistent with the remark no shown as Picture 6-2. ○ 2.PTZ direction control: Control PTZ moving direction ○ 3.
⑥.Capture [ ]：Capture Screen image and save to PC as *bmp image. ⑦.Recording [ ]：Operate DVR recording remotely ⑧Channel display [ ]：The icons stand for Single Channel display, Quad Channel display, 3x3 Channel display and 4x4 Channel display respectively. ⑨.Volume control [ ] Click or slide the control bar to adjust sound volume. 6.3.3.1. Playback Local File with Netviewer Run the Netviewer software, you will see the OFFLINE button displayed on the Login interface.
Chapter 7: Specifications Model 4CH Video System NTSC / PAL Compression Format Video：H.
Chapter 8: Windows Vista User 1、Open IE browse firstly, then enter into Tool bar- 3. and select to appear the below picture: 4. 2、Second, select icon and tick the settings of “ActiveX controls and plug-ins”to Enable, details as follows: Lastly after tick all the “Enable”, please click to exit. At this moment, you could input IP address to run your programme.
Open IE browser and input IP address and web port of DVR…computer will auto downloadand install the widget. We suggest Visita user set user access authority in order to make your PC safer. Setting processing as follows: Click [Start Set Control panel User account] to set user access authority shown as below picture. Remind: If the widgets ar e not downl oaded succes sfully, ple ase check if you r br owser’s safety l evel or firewall setting is too advanced.
Chapter 9: Appendix 9.1 Operation Function Table Type Title Description Time setting Language Select CH Setting Page Setting system date, time and format and day-light saving time setting 21 Setting system language 22 Setting CH title and position; adjusting image color parameter value; setting CH display to ON / Off 11 and time display/recording time overlaying to On/Off. Principle Setting Rec. Setting Setting image quality, resolution, volume, recording mode an pack time Rec.
Recording alarm setting Alarm icon Recording after power on Recording Mode Timing recording Manuel Recording AMR NLR NOR AMR AMR NLR ⊥ NLR ⊥ ⊥ ⊥ ⊥ ⊥ Video Loss Video Loss ⊥ ⊥ ⊥ ⊥ ⊥ List 9-2 When DVR is in recording mode, [ ] icon or [ ] icon will appear on the screen. But when the [ ] icons on the screen it indicates a motion was triggered. When [ ] icon appears on the screen, that mean a hard drive alarm has occurred. Alarm mode MD alarm HDD loss, HDD space full 9.3 Troubleshooting 1.
9.
