Specification Sheet

SKSFD3604P
36-INCH BUILT-IN FRENCH DOOR
REFRIGERATOR
CUTOUT DIMENSIONS – FLUSH INSTALLATION
INSTALLATION CLEARANCES – FLUSH INSTALLATION
**
Varies depending on the thickness
of the custom cabinet panel.
3/4" (19 mm) is relevant when
using the Stainless Steel Door
Panel Kit (optional accessory).
Door handle must be added to this dimension.
*
3/4"
(19 mm)**
36" (914 mm)
finished width
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
4"
(102 mm)
finished
return*
25"
(635 mm)
min. depth
84"
(2134 mm)
90°
115°
(452 mm)
20 3/16"
(513 mm)
17 13/16"
17 13/16"
(452 mm)
9 1/4"*
(235 mm)
9 1/4"*
(235 mm)
1 1/4"*
(32 mm)
1 1/4"*
(32 mm)
35 3/4"
(908 mm)
36"
cutout
(914 mm)
25"
(635 mm)
1/8"
(3 mm)
min.
1/8"
(3 mm)
min.
TOP VIEW
A minimum 4"
(102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
(35 mm)
1 3/8"
SKSFD3604P
36-INCH BUILT-IN FRENCH DOOR
REFRIGERATOR
CUTOUT DIMENSIONS – FLUSH INSTALLATION
INSTALLATION CLEARANCES – FLUSH INSTALLATION
**
Varies depending on the thickness
of the custom cabinet panel.
3/4" (19 mm) is relevant when
using the Stainless Steel Door
Panel Kit (optional accessory).
Door handle must be added to this dimension.
*
3/4"
(19 mm)**
36" (914 mm)
finished width
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
4"
(102 mm)
finished
return*
25" (635 mm)
min. depth
84"
(2134 mm)
90°
115°
(452 mm)
20 3/16"
(513 mm)
17 13/16"
17 13/16"
(452 mm)
9 1/4"*
(235 mm)
9 1/4"*
(235 mm)
1 1/4"*
(32 mm)
1 1/4"*
(32 mm)
35 3/4"
(908 mm)
36"
cutout
(914 mm)
25"
(635 mm)
1/8"
(3 mm)
min.
1/8"
(3 mm)
min.
TOP VIEW
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
(35 mm)
1 3/8"
CUTOUT DIMENSIONS – FLUSH INSTALLATION
Notes
Refrigerator can be installed ush with 3/4" custom panel
or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face o
f the
refrigerator ts ush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit
bre
aker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back
wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrup
ter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker
operation. Water pressure must be between 20 and
120 p.s.i.
Tubing should be long enough to extend to th
e front of
the refrigerator. Allow enough tubing to accommodate a
bend leading into the water line connection.
Water line can enter an opening through oor or back
wall.
Install a shut-o valve bet
ween the icemaker water valve
and cold water supply in the home.
Notes
Door Swing Clearances – The installation must allow
for clearances to adjacent walls or cabinets. This
refrigerator is equip
ped with a 2-position door stop. The
factory-set 115° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must
be add
ed to the dimension noted to determine the total
clearances required from adjacent cabinets or walls.
This clearance will vary depending on the custom handle
used. When using the Stainless St
eel Door Panel Kit w/
Handles or the Brushed Aluminum Handles (optional
accessories), the door handle clearance with door open
115° is 12" (305 mm).
INSTALLATION CLEARANCES – FLUSH INSTALLAT
ION
TOP VIEW
Page 3 of 5 | Effective 7/20 | WCAG
SKSFD3604P
36-INCH BUILT-IN FRENCH DOOR
REFRIGERATOR
CUTOUT DIMENSIONS – FLUSH INSTALLATION
* A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
Notes
Refrigerator can be installed flush with 3/4" custom panel or
optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the
refrigerator fits flush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall. Electrical
must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker
operation. Water pressure must be between 20 and 120
p.s.i.
Tubing should be long enough to extend to the front of the
refrigerator. Allow enough tubing to accommodate a bend
leading into the water line connection.
Water line can enter an opening through floor or back wall.
Install a shut-off valve between the icemaker water
valve and cold water supply in the home.
INSTALLATION CLEARANCES – FLUSH
INSTALLATION TOP VIEW
* Door handle must be added to this dimension.
** Varies depending on the thickness
of the custom cabinet panel. 3/4" (19
mm) is relevant when using the
Stainless Steel Door Panel Kit
(optional accessory).
Notes
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This refrigerator is
equipped with a 2-position door stop. The factory-set 115°
door swing can be adjusted to 90° if clearance to adjacent
cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the
dimension noted to determine the total clearances required from adjacent
cabinets or walls. This clearance will vary depending on the custom
handle used. When using the Stainless Steel Door Panel Kit w/ Handles
or the Brushed Aluminum Handles (optional accessories), the door handle
clearance with door open 115° is 12" (305 mm).
Page 3 of 5