Spec Sheet

Page 3 of 6 | Eective 6/18
SKSCF2401P
24" INTEGRATED
FREEZER COLUMN
CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION
SINGLE COLUMN
INSTALLATION CLEARANCES
TOP VIEW
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
24" (610 mm)
finished width
4"
(102 mm)
finished
return*
25" (635 mm)
min. depth
flush install
24"
(610 mm)
min. depth
proud install
84"
(2134 mm)
5"
(127 mm)
electrical
location
A minimum 4"
(102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
4"
(102 mm)
water
location
1 3/8"
(35 mm)
1/8"
(3 mm)
min.
1/8"
min.
(3 mm)
90°
115°
11 3/8"*
(288 mm)
24"
(610 mm)
26 1/4"
(666 mm)
24"
23 3/4"
(603 mm)
3/4"
(19 mm)**
(610 mm)
CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION
Notes
Freezer can be installed ush or proud with 3/4" custom panel
or optional stainless steel panel kit.
Flush – With a 25" (635 mm) cutout depth, the front face
of the freezer ts ush with 25" (635 mm) depth adjacent
cabinets.
Proud – With a 24" (610 mm) depth cutout, the front face
of the freezer extends approximately 3/4" (19 mm) beyond 24"
(610 mm) depth adjacent cabinets.
Electrical
A 115V, 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker
operation. Water pressure must be between 20 and 120 p.s.i.
Tubing should be long enough to extend to the front of the
freezer. Allow enough tubing to accommodate a bend leading
into the water line connection.
Water line can enter an opening through oor or back wall.
Install a shut-o valve between the icemaker water valve and
cold water supply in the home.
SINGLE COLUMN
Notes
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This freezer is
equipped with a 2-position door stop. The factory-set 115°
door swing can be adjusted to 90° if clearance to adjacent
cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must
be added to the dimension noted to determine the total
clearances required from adjacent cabinets or walls. This
clearance will vary depending on the custom handle used.
When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the
door handle clearance with door open 115° is 14" (356 mm).
INSTALLATION CLEARANCES
TOP VIEW
SKSCF2401P
24" INTEGRATED
FREEZER COLUMN
CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION
SINGLE COLUMN
INSTALLATION CLEARANCES
TOP VIEW
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
24" (610 mm)
finished width
4"
(102 mm)
finished
return*
25"
(635 mm)
min. depth
flush install
24"
(610 mm)
min. depth
proud install
84"
(2134 mm)
5"
(127 mm)
electrical
location
A minimum 4"
(102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
4"
(102 mm)
water
location
1 3/8"
(35 mm)
1/8"
(3 mm)
min.
1/8"
min.
(3 mm)
90°
115°
11 3/8"*
(288 mm)
24"
(610 mm)
26 1/4"
(666 mm)
24"
23 3/4"
(603 mm)
3/4"
(19 mm)**
(610 mm)
SKSCF2401P
24-INCH INTEGRATED COLUMN FREEZER