Installation Guide

ManualsBrandsSignature Hardware ManualsToiletsSignature Hardware Key West 1.28 GPF One Piece Elongated Skirted Chair Height Toilet - Seat Included, Left Hand Lever

Tape Measure

Cinta métrica

Closet Flange

Brida del inodoro

Closet Bolts

Pernos del inodoro

1.800.221.3379

SKIRTED ONE-PIECE TOILET

INODORO DE UNA PIEZA CON FALDÓN

SKU: 948415, 948416, 948414, 948420, 948413

REVISED 12/20/2019

CODES: SHAM241S, SHKW241S, SHBD241S, SHSK241S, SHAL241

GETTING STARTED

BEFORE YOU BEGIN

We recommend consulting a professional if you are

unfamiliar with installing plumbing ﬁxtures. Signature

Hardware accepts no liability for any damage to the

plumbing, ﬂoor, wall, or for personal injury during

installation.

Observe all local plumbing and building codes.

Unpack and inspect the toilet for shipping damage.

If any damage is found, contact our Customer

Relations team at 1-800-221-3379.

Ensure that you have gathered all the required

materials that are needed for the installation.

TOOLS AND MATERIALS:

HERRAMIENTAS Y MATERIALES:

ANTES DE COMENZAR

Le recomendamos que consulte a un profesional si no

sabe cómo instalar accesorios de plomería. Signature

Hardware no asume ninguna responsabilidad con

respecto a los daños causados a la plomería, el piso o la

pared, ni por lesiones personales que se produzcan

durante la instalación.

Cumpla con todas las normas locales de plomería y

construcción.

Retire el inodoro del empaque y veriﬁque si se

produjeron daños durante el envío. Si encuentra algún

daño, comuníquese con nuestro equipo de Servicio al

cliente al 1-800-221-3379.

CÓMO COMENZAR

Asegúrese de haber reunido todos los materiales

necesarios para la instalación.

Flathead

Screwdriver

Destornillador de

cabeza plana

Phillips

Screwdriver

Destornillador

Phillips

Pencil

Lápiz

Level

Nivelador

Drill

Taladro

Wax Ring

Anillo de cera

Flexible Supply Line

Línea de

suministro ﬂexible

3/4”

Y + 3/4”

Summary of content (6 pages)

PAGE 1
S K I R T E D O N E- P I E C E TO I L E T B INODORO DE UNA PIEZA CON FALDÓN A Y+ 3/4 ” SKU: 948415, 948416, 948414, 948420, 948413 3/4” Y TOOLS AND MATERIALS: HERRAMIENTAS Y MATERIALES: BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing ﬁxtures. Signature Hardware accepts no liability for any damage to the plumbing, ﬂoor, wall, or for personal injury during installation. Observe all local plumbing and building codes.
PAGE 2
S K I R T E D O N E- P I E C E TO I L E T A B INODORO DE UNA PIEZA CON FALDÓN SKU: 948415, 948416, 948414, 948420, 948413 A B BEFORE INSTALLATION ANTES DE LA INSTALACIÓN INSTALLATION INSTALACIÓN 1. Carefully inspect near the existing toilet to see if the toilet has a supply shut-oﬀ valve below the tank. If it does not, install one before installing the new toilet. 1. Place two new closet bolts into toilet ﬂange. 1. Coloque dos nuevos pernos de inodoro en la brida del inodoro. 1.
PAGE 3
n S K I R T E D O N E- P I E C E TO I L E T INODORO DE UNA PIEZA CON FALDÓN SKU: 948415, 948416, 948414, 948420, 948413 3. Place the connection “L” brackets onto the closet bolts, then attach the washers and nuts to the closet bolts, and tighten. 5. Firmly push the toilet down seating the bowl horn into the rubber gasket of seal plate assembly. Sealant or Plumber Putty Note: Make sure to not lift or rock the bowl after placement. If the watertight seal breaks.
PAGE 4
S K I R T E D O N E- P I E C E TO I L E T INODORO DE UNA PIEZA CON FALDÓN SKU: 948415, 948416, 948414, 948420, 948413 9. Water supply connection: Connect the ﬂexible supply line from the stop valve to the toilet ﬁll valve. Make sure not to use sealants on supply ﬁttings. Hand tighten supply line, then open stop valve and look closely for any water leaks. Adjust the tank water height to the indication mark on the ﬂush valve tube. 7.
PAGE 5
S K I R T E D O N E- P I E C E TO I L E T INODORO DE UNA PIEZA CON FALDÓN SKU: 948415, 948416, 948414, 948420, 948413 ADJUSTMENTS & TROUBLESHOOTING AJUSTES Y RESOLUCIÓN DE PROBLEMAS CONFIRM OPERATION CONFIRMAR LA OPERACIÓN Adjust ﬁll valve water line level to proper height. To adjust the water level rotate the adjustable rod, and that will adjust the height of the ﬂoat cup and change water level. Descargar el inodoro varias veces y revisar que ninguna conexión tenga pérdidas.
PAGE 6
S K I R T E D O N E- P I E C E TO I L E T INODORO DE UNA PIEZA CON FALDÓN SKU: 948415, 948416, 948414, 948420, 948413 Problem Problema Reason Razones Solution Solución Fill valve will not shut oﬀ - Water supply is closed - Float is stuck - Drain guard gets stuck -Flapper is stuck open - Water won’t shut oﬀ in tank - Turn on water supply angle stop - Loosen ﬁll valve nut and turn ﬁll valve away from back of tank - Clean drain guard - Check chain length and ﬂush valve seat - Turn oﬀ water, clean seal in