Installation Guide

ManualsBrandsSignature Hardware ManualsToiletsSignature Hardware Bradenton 1.28 GPF One-Piece Elongated Toilet - ADA Compliant, Seat Included

1.800.221.3379

STANDARD ONE-PIECE TOILET

INODORO ESTÁNDAR DE UNA PIEZA

SKU: 948418, 948417, 948421

REVISED 12/16/2019

CODES: SHKW241, SHBD241, SHSR241

GETTING STARTED

BEFORE YOU BEGIN

We recommend consulting a professional if you are

unfamiliar with installing plumbing ﬁxtures. Signature

Hardware accepts no liability for any damage to the

plumbing, ﬂoor, wall, or for personal injury during

installation.

Observe all local plumbing and building codes.

Unpack and inspect the toilet for shipping damage.

If any damage is found, contact our Customer

Relations team at 1-800-221-3379.

Ensure that you have gathered all the required

materials that are needed for the installation.

TOOLS AND MATERIALS:

HERRAMIENTAS Y MATERIALES:

ANTES DE COMENZAR

Le recomendamos que consulte a un profesional si no

sabe cómo instalar accesorios de plomería. Signature

Hardware no asume ninguna responsabilidad con

respecto a los daños causados a la plomería, el piso o la

pared, ni por lesiones personales que se produzcan

durante la instalación.

Cumpla con todas las normas locales de plomería y

construcción.

Retire el inodoro del empaque y veriﬁque si se

produjeron daños durante el envío. Si encuentra algún

daño, comuníquese con nuestro equipo de Servicio al

cliente al 1-800-221-3379.

CÓMO COMENZAR

Asegúrese de haber reunido todos los materiales

necesarios para la instalación.

Level

Nivelador

Flexible Supply Line

Línea de

suministro ﬂexible

Tape Measure

Cinta métrica

Closet Flange

Brida del Inodoro

Closet Bolts

Pernos del inodoro

Marker

Marcador

Phillips

Screwdriver

Destornillador

Phillips

Adjustable Wrench

Llave Ajustable

Hacksaw

Sierra para

metales

Silicone Sealant

(100% Neutral Cure)

Sellador de silicona

(100% curado neutro)

3/4”

Y + 3/4”

Summary of content (5 pages)

PAGE 1
S TA N D A R D O N E - P I E C E T O I L E T INODORO ESTÁNDAR DE UNA PIEZA B A SKU: 948418, 948417, 948421 Y+ 3/4 ” 3/4” Y BEFORE YOU BEGIN TOOLS AND MATERIALS: HERRAMIENTAS Y MATERIALES: We recommend consulting a professional if you are unfamiliar with installing plumbing ﬁxtures. Signature Hardware accepts no liability for any damage to the plumbing, ﬂoor, wall, or for personal injury during installation. Observe all local plumbing and building codes.
PAGE 2
S TA N D A R D O N E - P I E C E T O I L E T A B INODORO ESTÁNDAR DE UNA PIEZA SKU: 948418, 948417, 948421 A B INSTALLATION INSTALACIÓN BEFORE INSTALLATION ANTES DE LA INSTALACIÓN 1. Place two new closet bolts into the slot on the toilet ﬂange. 1. Carefully inspect near the existing toilet to see if the toilet has a supply shut-oﬀ valve below the tank. If it does not, install one before installing the new toilet. 1. Coloque dos nuevos pernos de inodoro en la ranura de la brida del inodoro. 1.
PAGE 3
S TA N D A R D O N E - P I E C E T O I L E T INODORO ESTÁNDAR DE UNA PIEZA SKU: 948418, 948417, 948421 3. Align and lower toilet over ﬂange and bolts. Apply your full body weight around the toilet to set seal. 4. Place bolt cap base on bolt, then place metal washer and nut. Alternately tighten the ﬂange nuts until the bowl is seated to the ﬂoor. Note: Make sure to not lift or rock the bowl after placement. If the watertight seal breaks.
PAGE 4
S TA N D A R D O N E - P I E C E T O I L E T INODORO ESTÁNDAR DE UNA PIEZA SKU: 948418, 948417, 948421 ADJUSTMENTS & TROUBLESHOOTING AJUSTES Y RESOLUCIÓN DE PROBLEMAS 5. If bolts extend more than 1/4” (6mm) over top of the nuts, cut oﬀ excess. Conceal with bolt cap. 5. Si los pernos sobresalen más de 1/4" (6 mm) sobre la parte superior de las tuercas, corte el exceso. Oculte con la tapa del perno. Adjust ﬁll valve water line level to proper height.
PAGE 5
S TA N D A R D O N E - P I E C E T O I L E T INODORO ESTÁNDAR DE UNA PIEZA SKU: 948418, 948417, 948421 Reason Razones Solution Solución Fill valve will not shut oﬀ - Water supply is closed - Float is stuck - Drain guard gets stuck -Flapper is stuck open - Water won’t shut oﬀ in tank - Turn on water supply angle stop - Loosen ﬁll valve nut and turn ﬁll valve away from back of tank - Clean drain guard - Check chain length and ﬂush valve seat - Turn oﬀ water, clean seal inside ﬁll valve La válvula de lle