Installation Sheet

ManualsBrandsSignature Hardware ManualsBathroom FaucetsSignature Hardware 1.2 GPM Bridge Bathroom Faucet with Pop-Up Drain Assembly

8” BRIDGE BATHROOM FAUCET INSTALLATION

GETTING STARTED

BEFORE YOU BEGIN

We recommend consulting a professional if you are

unfamiliar with installing plumbing ﬁxtures. Signature

Hardware accepts no liability for any damage to the

faucet, plumbing, sink, counter top, or for personal injury

during installation.

Observe all local plumbing and building codes.

Unpack and inspect the faucet for shipping damage. If

any damage is found, contact our Customer Relations

team at 1-866-855-2284.

Ensure that you have gathered all the required

materials that are needed for the installation.

For these instructions, it is assumed that the old

faucet has been completely removed and any

necessary repairs or modiﬁcations to the water

supply have been completed.

TOOLS AND MATERIALS:

Plumbers

Tape

Thread

Sealant

Adjustable

Wrench

Small

Bucket

18” Bridge Bathroom Faucet Installation Instructions

Phillips

Screwdriver

907536, 907537, 913187, 919191,

919198

SKU(s):

Summary of content (6 pages)

PAGE 1
SKU(s): 907536, 907537, 913187, 919191, 919198 8” BRIDGE BATHROOM FAUCET INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing ﬁxtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation. TOOLS AND MATERIALS: Plumbers Tape Thread Sealant Small Bucket Phillips Screwdriver Adjustable Wrench Observe all local plumbing and building codes.
PAGE 2
8” BRIDGE BATHROOM FAUCET INSTALLATION INSTALLATION 1. Ensure that the water supply below your sink is completely shut oﬀ by turning the shutoﬀ valves all the way to the right. 3. From below, slide the metal washers onto the threaded shanks. Thread the locknuts onto the shanks until hand-tight, then ﬁnish tightening using an adjustable wrench. Tip: Place a small bucket below your workspace to catch any water that may drip during the installation process. OFF 2.
PAGE 3
8” BRIDGE BATHROOM FAUCET INSTALLATION 5. Connect the main water supply lines to the faucet. Apply plumber’s tape or thread sealant to the threads before tightening. Use an adjustable wrench to tighten, but be careful not to overtighten. Ensure that you are connecting the hot and cold lines appropriately. 7. Proceed to the drain installation. Once completed, remove the aerator from the spout and turn the faucet on for approximately 60 seconds to remove any dust or loose sediment from the water lines.
PAGE 4
8” BRIDGE BATHROOM FAUCET INSTALLATION DRAIN INSTALLATION 1. Remove the ﬂange by unthreading it from the drain body. Remove the ﬂat rubber gasket as well. Lift Rod Stopper Stopper Tailpiece Drain Flange & Flat Rubber Gasket Thumb Screw 2. Set the ﬂat rubber gasket over the drain hole in your sink, then insert the ﬂange into the drain hole.
PAGE 5
8” BRIDGE BATHROOM FAUCET INSTALLATION 3. From beneath the sink, reattach the ﬂange by threading it back onto the drain body. 4. Connect the drain lever by threading it into the hole on the side of the drain body. The lever must pass through the hole in the stopper tailpiece to function properly. Apply a bit of thread sealant or plumber’s tape to the threads before attaching. 5. Position the drain so that the lever is facing the back of the ﬁxture, in line with the faucet’s lift rod.
PAGE 6
8” BRIDGE BATHROOM FAUCET INSTALLATION 7. Use the link to attach the faucet’s lift rod to the drain lever. Pinch the metal clip located on the drain lever to remove. Slide one end of the clip back onto the lever, followed by the link, then the second end of the clip to secure. 9. Make any ﬁnal adjustments to the positioning of the link and drain lever as needed. Adjust until the drain fully opens and closes. OPEN CLOSED 8.