Operator`s manual

Signametrics 42
Power Line Rejection Command/Response mode
H/W Trigger mode min. Read
min. Read Interval(s) / max
meas. rate(Hz)
Interval(s) / max meas. Rate
(Hz)
Aperture 60 50Hz 400Hz
Hz
5.1200s [1]
√ √ √
5.121s / 0.2 N/A
5.0666s [1]
√
5.0677s / 0.2 N/A
2.08s [1]
√ √
2.081s / 0.5 N/A
2.0s [1]
√ √ √
2.001s / 0.5 N/A
1.06666s [1]
√
1.067s / 1 N/A
960ms [1]
√ √
0.9605s / 1 N/A
533.33ms [1]
√
533.6ms / 2 N/A
480ms [1]
√ √
480.2ms / 2 N/A
266.666ms [1]
√
268ms / 4 N/A
160.0ms
√ √ √
166ms / 6 160.3 ms / 6
133.33ms
√
134ms / 8 133.5 ms / 8
80.00ms
√ √
80.4ms / 13 80.2 ms / 13
66.6
√
66.713 ms / 15 667ms 67.2ms / 15
40.00ms
√ √
40.4ms / 25 40.32 ms / 24.8
33.333ms
√
33.7ms / 30 33.38 ms / 30
20.00ms
√ √
20.35ms / 50 20.33 ms / 50
16.6667ms
√
16.9ms / 59 16.89 ms / 59
10ms 10.36ms / 97 10.25 ms / 97
8.333ms 8.68ms / 115 8.503 ms / 115
5ms 5.36ms / 185 5.187 ms / 185
4.16 ms / 220 4.274 ms / 220 667ms 4.52
2.5ms 2.86ms / 350 2.614 ms / 350
2.0833ms 2.44ms / 410 2.216 ms / 410
1.25ms 1.6ms / 625 1.380 ms / 625
1.0417ms 1.39ms / 719 1.158 ms / 864
625µS 917µs / 1,090 728 µs / 1,370
[1] Not available with any of the Triggered modes.
Table 4.2: The SM2060 has 26 apertures available, ranging from 5 Seconds to 625uSec
. The table contains all
available measurement apertures and corresponding minimum read intervals and measurement rates.
4.6 RTD Temperature Measurement (SM2064)
For temperature measurements, the SM2064 measure and linearize RTDs. 4-wire RTD can be used by selecting the
appropriate RTD type. Any ice temperature resistance between 25 Ω and 10 kΩ can be set for the platinum t
RTDs. Copper RTDs can have ice temperature resistance values of 5 Ω to 200 Ω. The highest accuracy is obtained
from 4-wire devices, since this method eliminates the error introduced by the r
ype
esistance of the test leads. The
onnection configuration for RTDs is identical to 4-wire Ohms.
r allows monitoring of the DMM’s internal temperature. This provides the
ng the
ce
The semiconductor part types. This function is designed to
c
4.7 Internal Temperature (SM2064)
A special on board temperature senso
means to determine when to run the self-calibration function (S-Cal) for the DMM, as well as predicti
performance of the DMM under different operating conditions. When used properly, this measurement can enhan
the accuracy and stability of the DMM. It also allows monitoring of the PC internal temperature, which is important
for checking other instruments in a PC-based test system.
4.8 Diode Characterization
Diode measurement function is used for characterizing
display a semiconductor device’s forward or reverse voltage. The DMM measures diode voltage at a selected
current. The available source currents for diode I/V characterization include five DC current values, 100 ηA, 1 µA,
10 µA, 100 µA and 1 mA. The SM2064 have an additional 10 mA range. The SM2064 also has a variable current