Installation guide

Signamax Connectivity System _____________________________ ___ _____________ 098-8280/098-82160
Notes:
1. OSD Menu control is only available when the OSD menu is activated on the screen. To activate the OSD menu, use the hotkey sequence ScrLk + ScrLk + (Space Bar). For detailed OSD operation
reference, please refer to relevant sections in Chapter 3, Operation of the User Manual.
2. Note that a, b, y and z each denotes a number key. (ab) = 01 ~ 16 ; (yz) = 01 ~ 04 or 01 ~ 08 or 01 ~ 16. For example, ScrLk + ScrLk + 03 + 09 is for bank 3 port 9. When using a single KVM Switch
configuration, the default bank no. is 01, therefore hit ScrLk + ScrLk + 01 + 12 for port 12 for a single KVM Switch configuration.
3. The factory default of password configuration is no password protection. And the password is default to 00000000.
www.signamax-us.com www.signamax-eu.com
Quick Reference Sheet
QUICK REFERNCE SHEET for KVM Switch Operation Commands Hotkeys/ OSD Menu / Front-Panel Buttons
Command Hotkeys OSD control
1
Front-panel Description User Guide
Select PC
ScrLk + ScrLk + (a) + (b) + (y) + (z)
(ab = bank no. ; xy = channel no.)
2
Cursor keys to navigate
Enter to select
Press corresponding button yz
on Switch ab for channel yz on
bank ab.
Select the active bank (switch) and
channel
Page 21
Next lower channel ScrLk + ScrLk + ↑ (arrow up)
Cursor keys to navigate
Enter to select
Press corresponding button
Select the next lower connected
channel
Page 22
Next higher channel ScrLk + ScrLk + ↓ (arrow down)
Cursor keys to navigate
Enter to select
Press corresponding button
Select the next higher connected
channel
Page 22
Next lower bank
ScrLk + ScrLk + PgUp PgUp
Press corresponding button on
that switch
Select the next lower bank (switch)
when multiple switch units are
daisy-chained together
Page 22
Next higher bank
ScrLk + ScrLk + PgDn PgDn
Press corresponding button on
that switch
Select the next higher bank
(switch ) when multiple switch
units are daisy-chained together
Page 23
Autoscan Beep Sound
On/Off
ScrLk + ScrLk + B -- --
Toggle on/off the beep sound for
switching confirmation while
autoscanning
Page 23
Reflash EEPROM
ScrLk + ScrLk + R -- --
Restore the EEPROM settings to
the factory default
Page 23
Find PC by Name
ScrLk + ScrLk + F -- --
Search the presence of a specific PC
by its name
Page 24
Change PC Name
--
Cursor keys to navigate
Enter (Ins) to select/edit PC
name
-- Change the PC name Page 25
Reset / Initialize KVM
ScrLk + ScrLk + End --
Button 1 (Press and hold down
for 2”)
Reset the KVM Switch either for
daisy-chain setup initialization or
for switch system reboot.
Page 25
Show OSD Menu
ScrLk + ScrLk + (Space Bar) -- --
Activate the OSD Menu on the
console screen
Page 25
Autoscan
ScrLk + ScrLk + S --
Last button (Press and hold
down for 2”)
Autoscan through every connected
channel for quick screen browsing
of each channel.
Page 25
Stop Autoscan
Any key -- Press any push button Terminate Autoscan activity Page 25
Autoscan Delay
--
Cursor keys to navigate
Enter/Ins to select and edit
--
Specify delay time within a range of
5 ~ 99 seconds (default = 10 sec.)
Page 26
OSD Remain Time
--
Cursor keys to navigate
Enter/Ins to select and edit
--
Change the OSD Menu Remain
Time
Page 26
Password Config
3
--
Cursor keys to navigate
Enter/Ins to select and edit
-- Enable/disable password protection Page 26
Password Change
3
--
Cursor keys to navigate
Enter/Ins to select and edit
-- Change the password Page 27