5 10/100TX + 1 100FX Industrial Switch w/POE Model: 900-7405P1GC16 SIGNAMAX a.s. Seat: Palackeho trida 38, 612 00 Brno, CZ l Office: Vlarska 22, 627 00 Brno, CZ T:+420 533 338 854 l F:+420 533 338 883 l www.signamax.
The information contained in this document is subject to change without prior notice. Copyright (C). All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of Contents 1. Introduction ........................................................................................................................... 5 1.1 Features............................................................................................................... 6 1.2 Product Panels..................................................................................................... 6 1.3 LED Indicators....................................................................................
1. Introduction The switches are 5-port Fast Ethernet switches which are featured with four copper ports and one combo port. The combo port comes with one RJ-45 and one SFP slot. The SFP slot can be mounted with a fiber transceiver optionally to support a fiber connection. For more coming PoE (Power Over Ethernet) applications, the PoE switch model is equipped with PoE design in four copper ports. With proper 48VDC power supply, it is able to deliver power to four PoE PD devices via Cat.5 cables.
• Power input interface: Industrial screw terminal block and DC power jack for external commercial power adapter as option • Screw panel and DIN rail mounting support for industrial enclosure • Industrial-rated Emission and Immunity performance SIGNAMAX a.s. Seat: Palackeho trida 38, 612 00 Brno, CZ l Office: Vlarska 22, 627 00 Brno, CZ T:+420 533 338 854 l F:+420 533 338 883 l www.signamax.
1.1 Features Provides 5 10/100Mbps RJ-45 and one 100Mbps SFP slot All copper ports support auto-negotiation and auto-MDI/MDI-X detection Provides full wire speed forwarding Supports IEEE 802.3x flow control for full-duplex and backpressure for half-duplex Provides SFP slot for optional optical fiber connection Provides four IEEE 802.
1.4 Specifications Copper Ports w/h PSE (P2-P5) Compliance IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX Connectors Shielded RJ-45 jacks Pin assignments Auto MDI/MDI-X detection Configuration Auto-negotiation Transmission rate 10Mbps, 100Mbps Duplex support Full/Half duplex Network cable Cat.5 UTP Power over Ethernet IEEE 802.3af-compliant PSE (function equipped in PoE Model only) Combo Port (P1) Compliance IEEE 802.3 10Base-T, IEEE 802.
Back pressure for half duplex operation Broadcast Storm Protection design SIGNAMAX a.s. Seat: Palackeho trida 38, 612 00 Brno, CZ l Office: Vlarska 22, 627 00 Brno, CZ T:+420 533 338 854 l F:+420 533 338 883 l www.signamax.
Power over Ethernet Function (PoE Model) PSE Pin 4,5 Positive of power voltage (Typical 48VDC) PSE Pin 7,8 Negative of power voltage (Typical 48VDC) Discovery PD resistance 15K ~ 33K PD Classification Class 0 ~ 4 Power delivery 15.4W max. (per port) Protection Under voltage protection Over voltage protection Over current detection DC IN Power Input Interfaces DC IN Jack ( -D 6.3mm / + D 2.0mm) DC IN Terminal Block (screw type) Operating Input Voltages +6 ~ 60VDC Power Consumption 3W max.
2. Installation 2.1 Unpacking The product package contains: • The switch unit • One product CD-ROM 2.2 Safety Cautions To reduce the risk of bodily injury, electrical shock, fire, and damage to the product, observe the following precautions. • Do not service any product except as explained in your system documentation. • Opening or removing covers may expose you to electrical shock. • Only a trained service technician should service components inside these compartments.
SIGNAMAX a.s. Seat: Palackeho trida 38, 612 00 Brno, CZ l Office: Vlarska 22, 627 00 Brno, CZ T:+420 533 338 854 l F:+420 533 338 883 l www.signamax.
2.4 Din-Rail Mounting The steps to mount the switch on a Din-rail are: One Din-rail mounting bracket is provided in the product package as shown below: Install the bracket on the bottom of the switch unit. Mount the device on a Din-rail. SIGNAMAX a.s. Seat: Palackeho trida 38, 612 00 Brno, CZ l Office: Vlarska 22, 627 00 Brno, CZ T:+420 533 338 854 l F:+420 533 338 883 l www.signamax.
2.5 Panel Mounting One optional panel mounting bracket is available for your purchase as shown below: Install the bracket on the bottom of the switch unit. The final dimension after panel bracket is installed is shown below: 2.6 Applying Power The switch provides two types of power interfaces, terminal block and DC power jack for receiving DC power input from external power supply system. SIGNAMAX a.s.
Using Terminal Blocks Three terminal contacts are provided: Vdc Positive (+) terminal Vdc Negative (-) terminal Chassis ground * Working Vdc for general application: +6V ~ +60VDC * Working Vdc for PoE application : +43V ~ +54VDC (Typ. 48V) One 3P terminal plugs are provided together with the switch. The plug is shown below: Power wires : 24 ~ 12AWG (IEC 0.5~2.5mm2) Install the power source wires with the plug properly. Then, plug in the terminal block socket.
3. Making Connections 3.1 Making UTP Connections The copper ports support the following connection types and distances: Network Cables 10BASE-T: 2-pair UTP Cat. 3,4,5 , EIA/TIA-568B 100-ohm 100BASE-TX: 2-pair / 4-pair UTP Cat. 5, EIA/TIA-568B 100-ohm Link distance: Up to 100 meters Auto MDI/MDI-X Function This function allows the port to auto-detect the twisted-pair signals and adapts itself to form a valid MDI to MDI-X connection with the remote connected device automatically.
Make sure the Rx-to-Tx connection rule is followed on the both ends of the fiber cable. Network Cables Multimode (MMF) - 50/125, 62.5/125 Single mode (SMF) - 9/125 SIGNAMAX a.s. Seat: Palackeho trida 38, 612 00 Brno, CZ l Office: Vlarska 22, 627 00 Brno, CZ T:+420 533 338 854 l F:+420 533 338 883 l www.signamax.
3.3 Making PoE Connections This section describes how to make a connection between a PSE port and a PoE PD device. For the PoE switch model, Port 2, Port 3, Port 4 and Port 5 are equipped with PoE PSE function. The ports are enabled to deliver power together with network signal to a connected powered device via Cat.5 cable. To make a PoE connection, the following check points should be noted: 1. For safety reason, the connected PoE PD (Powered Device) must be a IEEE 802.3af-compliant device.
3.4 LED Indication LED Function POWER Power status State ON OFF LINK/ACT Port link status ON Interpretation The power is supplied to the switch. The power is not supplied to the switch. A port link is established. (No traffic) BLINK Port link is up and there is traffic. OFF 100M/10M Port speed status ON OFF PoE STATUS Port PoE power ON OFF SFP/RJ-45 Port1 status ON OFF Port link is down. Speed 100M is selected. Speed 10M is selected. PoE power is delivered on the port.
4. Applications 4.1 Applications with Basic Switch Model The following figure illustrates a basic switch model connects five computers via Cat.5 cables. The following figure illustrates a basic switch model connects four computers via Cat.5 cables and uplink to a fiber backbone network. SIGNAMAX a.s. Seat: Palackeho trida 38, 612 00 Brno, CZ l Office: Vlarska 22, 627 00 Brno, CZ T:+420 533 338 854 l F:+420 533 338 883 l www.signamax.
4.2 Applications with PoE Switch Model The figure below illustrates a PoE switch connects four PoE IP cameras via Cat.5 cables and uplinks to a fiber backbone: The figure below illustrates a PoE switch connects four PoE WLAN access points via Cat.5 cables and uplinks to a backbone: SIGNAMAX a.s. Seat: Palackeho trida 38, 612 00 Brno, CZ l Office: Vlarska 22, 627 00 Brno, CZ T:+420 533 338 854 l F:+420 533 338 883 l www.signamax.
The figure below illustrates a PoE switch powered by a 48V DC power adapter connects four PoE media converters via Cat.5 cables and uplinks to a fiber backbone: SIGNAMAX a.s. Seat: Palackeho trida 38, 612 00 Brno, CZ l Office: Vlarska 22, 627 00 Brno, CZ T:+420 533 338 854 l F:+420 533 338 883 l www.signamax.
