User manual

ManualsBrandsSignaMax ManualsComputer equipment065-7940B-WS

24-Port Gigabit Web Smart Switch

with 4 SFP (Mini-GBIC) slots

User Manual

V1.4

(April 2008)

Summary of content (43 pages)

PAGE 1
24-Port Gigabit Web Smart Switch with 4 SFP (Mini-GBIC) slots User Manual V1.
PAGE 2
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports COPYRIGHT All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photo copying, recording or otherwise, without the prior written permission of the publisher. FCC WARNING This equipment has been tested and found to comply with the limits for a class A device, pursuant to part 15 of FCC rules.
PAGE 3
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Table of Contents UNPACKING INFORMATION...................................... 5 INTRODUCTION........................................................ 5 GENERAL DESCRIPTION..........................................................................5 KEY FEATURES ......................................................................................6 THE FRONT PANEL .................................................................................
PAGE 4
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports AGGREGATION/ TRUNK CONFIGURATION .............................................. 17 QUALITY OF SERVICE ........................................................................... 18 MIRROR ............................................................................................... 22 RATE LIMIT ......................................................................................... 23 SNMP .................................................
PAGE 5
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Unpacking Information Congratulations on purchasing this Signamax 065-7940B-WS 24-port Gigabit Web Smart Switch with 4 SFP module Combo slots. Before you start, please verify that your package contains the following items: 1. 2. 3. 4.
PAGE 6
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Key Features 24 (twenty-four) 10/100/1000Mbps Gigabit Ethernet ports. 4 (four) SFP slots for optional fiber connection. Supports auto-detection for SFP module insertion Auto-discovery function for easy Network management. 8K MAC address entries and 24 groups VLAN table Supports Port Mirroring. Supports up to 8 ports and 12 groups port aggregation.
PAGE 7
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Attention：：The SFP module (SFP) slots share their LED indicators with their interchangeable Gigabit RJ-45 (copper) ‘combo’ ports (the last 4 copper ports). Use of a SFP module slot automatically disables its corresponding copper port.
PAGE 8
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Installation This Signamax 065-7940B-WS Switch can be placed on your desktop or mounted in a rack. Installation is very easy. Users can use all the features of the Switch by simply attaching the cables and turning the power on. Before installing the Switch, we strongly recommend that … 1. … the Switch must be placed in an environment that is well ventilated – a minimum space around the unit of 25mm is recommended. 2.
PAGE 9
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Media 10/100/1000 Mbps copper 1000 Mbps Fiber (SFP module required) Speed 10 Mbps 100 Mbps 1000 Mbps 1000 Mbps Wiring Category 3,4,5 UTP/STP Category 5 UTP/STP Category 5,5e UTP/STP The cable type differs according to the SFP module you choose. Please refer to the instructions that came with your SFP module.
PAGE 10
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Description of Switch Functions Jumbo Frame The Signamax 065-7940B-WS Switch supports Jumbo Frames, which means that it can transmit the same data in fewer frames. This helps to ensure fewer overheads, shorter processing time, and fewer interruptions. NOTE: To enable Jumbo Frame, Flow Control should be enabled in advance.
PAGE 11
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Management guide Access the Switch This section shows you how to access and use the Signamax 065-7940B-WS Switch’s advanced management capability, which can be accessed via console port or Internet Browser over the network (in-band). Manage via Command Line Interface To start the Command Line Interface, please connect a PC COM port to the RS-232 connector and activate terminal emulation software (e.g. Windows’ HyperTerminal).
PAGE 12
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Homepage After successful log-in, the “SYSTEM Configuration” page appears (this is also the Homepage). You can click on the hyperlinks on the left side of each page to get access to each management function.
PAGE 13
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports System The System window provides the Switch’s system information and allows users to configure most of these properties (see table under screenshot for details). Items MAC Address S/W Version IP Address Subnet Mask Gateway Management VLAN User Name Password System Name Functions The MAC address of this device.. The software version of this device.
PAGE 14
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Port This Port Configuration page shows the link status of each port and allows users to configure speed, flow control and maximum frame size for each port. Items Link Mode Flow Control Max Frame length Functions Shows the link status of each port. The column lights green and shows the link speed if there is valid connection on the port. Select a speed for this port. “Auto Speed” enables auto-negotiation.
PAGE 15
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports VLAN VLAN divides the network members into groups to reduce packet collisions and improve the network efficiency. The switch supports 802.1q tag-based VLAN. Please follow the instructions to configure. To add new VLAN groups, 1. Fill in a VLAN ID, from 2 to 4094, in the “VLAN\Port” column. 2. Select the ports for each VLAN group. 3. Click the “Apply” button to execute. To delete a VLAN group 1.
PAGE 16
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports PVID When the VLAN-enabled Switch receives a tagged packet, the packet will be sent to the port’s default VLAN according to the PVID (port VLAN ID) of the receiving port. Items Port Egress Functions Port Number 1~24 Select “tagged” in the drop menu to enable the PVID checking and tag inserting of one port, and select “untagged” to cancel.
PAGE 17
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Aggregation/ Trunk Configuration To set up the port trunk groups, put the selected ports’ numbers into the same Aggregation group. You can choose up to eight groups. Don’t forget to click “Apply” to save the settings. There are three aggregation modes for you to set up, SMAC, DMAC, and XOR. SMAC mode selects the path of packets according to Source MAC while DMAC mode selects path according to Destination MAC.
PAGE 18
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Quality of Service QoS enhances communication quality by giving precedence to certain classes of packets.
PAGE 19
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Port-based mode QoS: Port-based QoS allows users to configure each port as having a high or low priority. To assign a priority level to each port: 1. 2. 3. 4. Select “Port” in the “Mode” column for those ports that are going to function as part of port-based QoS. Click the “Apply” button. Click the “Port priority” button. The “Port Priority Setting” appears. Click on the drop menu to specify priority levels. Click “Apply” to execute.
PAGE 20
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Tag-based QoS: Tag-based QoS assigns packet priority according to the tags on the packets. To configure Tag-based QoS: 1. 2. 3. 4. 5. Select “Tagged” in the “Mode” column for those ports that are going to perform tag-based QoS. Click the “Apply” button. Click the “Tag priority” button. The “Tag Priority Setting” page shows up. Select the port that you are going to configure from the drop menu.
PAGE 21
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports DSCP-mode QoS: DSCP-mode QoS assigns packet priority according to the types of the incoming packets. It distinguishes packets according to the “Delay”, “Throughput” and “Reliability” information attached to the packet.
PAGE 22
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Mirror The Mirror function copies all the packets that are transmitted by the source port to the destination port. It allows administrators to analyze and monitor the traffic of the monitored ports. Mirror Configuration: 1. 2. 3. Select those ports that are going to be monitored by marking the checkboxes in the “Monitor Port” column. Click the drop menu in the “Sniffer Port” column.
PAGE 23
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Rate Limit The “Rate Limit” page allows users to limit the bandwidth for each port and configure the rules for Storm Control, which limits the flow of broadcast and multicast To perform storm control: 1. 2. Click on each drop list to specify a speed for each frame type. Click the “Apply” button to execute your configuration.
PAGE 24
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports SNMP This device supports SNMP-management, which allows network administrators to monitor and configure this device with SNMP software. To allow this device to be managed via SNMP: 1. 2. 3. 4. Select “enable” in the drop menu. Specify a trap IP. A trap IP is the destination port for sending trap information, which is usually the IP address of network administrators.
PAGE 25
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Discovery After installing a series of our switches, the discovery management tool helps users to search and get access to those switches within the LAN. Note: The discovery tool lists a maximum of 16 devices respectively for auto and manual modes. Auto Search 1. Click the “Apply” button to start. 2. The devices being found are listed below. 3. Click the IP address hyperlink to get access to the device. Manual Add Add 1.
PAGE 26
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Statistics Overview The Statistics Overview is provided for users to see the general transmitting and receiving status of each port. You may click the “Clear” button to clean all statistics or click the “Refresh” button to renew the statistics. Detailed Statistics The Detailed Statistics is provided for users to see the detailed transmitting and receiving status of each port. Please click the hyperlinks above to select a port.
PAGE 27
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Restart Restart: To restart the system, click the “Yes” button. The system restarts and shows the authentication window. Please fill in the username and password to continue. Factory Default Restore Factory Default: To restore the factory default settings, click the Yes button. Note: The IP address of the device will also be reconfigured to the factory default setting, which is 192.168.0.254.
PAGE 28
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Software Upload This “Software Upload” page allows users to upgrade firmware for this Switch. To perform firmware upgrade: 1. Click the “Browse” button 2. Locate the firmware file 3. Click the “Upload” button to execute. Note: This new firmware is going to be applied on the remaining flash that you have NOT selected in “Smart Boot”, that is, the new firmware is going to be applied on the flash that is NOT chosen as the booting flash.
PAGE 29
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Product Specifications Standards Interface IEEE802.3 10BaseT IEEE802.3u 100BaseTX IEEE802.3x full-duplex operation and flow control IEEE802.3ab/z 1000BaseT IEEE802.1Q VLAN interoperability IEEE802.
PAGE 30
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Appendix- Command Line Interface Start-up and Terminal configuration To start the Command Line Interface, please connect a PC COM port to the RS-232 connector and activate terminal emulation software (e.g. Windows’ HyperTerminal). The terminal emulation software should be started in the following configuration: 1. Data rate: 115200 baud 2. Data format: 8 data bits, 1 stop bit and no parity 3. Flow control: none. 4.
PAGE 31
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Command Hierarchy After logging in, press ? + to show the 9 command groups. System Console Port VLAN Aggr QoS Mirror IP SNMP Ratelimit Exit - System commands - Console commands - Port commands - VLAN commands - Aggregation commands - QoS commands - Mirror commands - IP commands - SNMP commands - Rate setup commands - Logout commands Press ? or help to get help.
PAGE 32
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Command Description These are the group commands of the command line interface: Command groups: System - System commands Console - Console commands Port - Port commands VLAN - VLAN commands Aggr - Aggregation commands QoS - QoS commands Mirror - Mirror commands IP - IP commands SNMP - SNMP commands Ratelimit - Rate setup commands Exit - Logout commands System Commands Commands at System level: System Configuration [all] System Restore Defau
PAGE 33
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Description: Set or show the console password. The empty string ("") disables the password check. []: Password string of up to 16 characters. System Systemname [] Description: Set or show the system name. []: String of up to 16 characters (default: Show system name). System Reboot Description: Reboot the switch.
PAGE 34
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Port Commands Commands at Port level: Port Configuration [] Port Mode [] [] Port Flow Control [] [enable|disable] Port Admin [] [enable|disable] Port MaxFrame [] [|reset] Port Statistics [] [clear] -----#Note: If you want to make maxframe bigger than 1518, the [Flow Control] should be enabled! Port Configuration [] Description: Show the configured and curr
PAGE 35
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Port Admin [] [enable|disable] Description: Set or show the admin state for the port. [] : Port list (default: All ports). [enable|disable]: Enable or disable admin state (default: Show admin state). Port MaxFrame [] [|reset] Description: Set or show the maximum frame size in bytes (including FCS) for frames received on the port.
PAGE 36
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports VLAN Commands Commands at VLAN level: VLAN Configuration [] VLAN Add [] VLAN Delete VLAN Lookup VLAN Egress [] [untagged|tagged] VLAN PVID [] [|none] VLAN OnlyTag [] [enable|disable] VLAN Configuration [] Description: Show the VLAN egress mode, port VLAN ID and accepted frame type for the port and the permanently stored VLAN table.
PAGE 37
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports VLAN Egress [] [untagged|tagged] Description: Set or show the VLAN egress mode setting for the port. Egress untagged ports will strip the VLAN tag from received frames. Egress tagged ports will not strip the tag from received frames []: Port list (default: All ports). [tagged|untagged]: (default: Show egress tag setting). VLAN PVID [] [|none] Description: Set or show the port VLAN ID.
PAGE 38
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Aggregation Commands Commands at Aggr level: Aggr Configuration Aggr Add Aggr Delete Aggr Lookup Aggr Mode [smac|dmac|xor] Aggr Configuration Description: Shows the aggregation groups and the aggregation mode. Aggr Delete Description: Delete link aggregation group. : Port list. Aggregations including any of the ports will be deleted.
PAGE 39
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports QoS Commands Commands at QoS level: QoS Configuration [] QoS Mode [] [tag|port|diffserv] QoS Port [] [] QoS Tagprio [] [] [] QoS DiffServ [] [] range: low|normal|medium|high QoS Configuration [] Description: Show the configured QoS mode and the priority setting of all ports. []: Port list (default: All ports).
PAGE 40
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports QoS DiffServ [] [] Description: Set or show the IP Differentiated Services mapping. []: IP DSCP number, 0-7. [] : range: low|normal|medium|high Mirror Commands Commands at Mirror level: Mirror Configuration Mirror Port [] Mirror Source [] [enable|disable] Mirror Configuration Description: Show the mirror destination port and mirror mode for source ports.
PAGE 41
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports IP Commands Commands at IP level: IP Configuration IP Setup [ [ []]] [] IP Web management [enable|disable] IP Configuration Description: Show IP configured IP address, mask, gateway, VLAN ID and mode. IP Setup` Description: Setup or show IP configuration. []: IP address. (default: Show IP configuration) [] : IP subnet mask (default: Subnet mask for address class).
PAGE 42
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Activate or deactivate the SNMP. [enable|disable]: Enable/disable SNMP (default: Show SNMP mode). SNMP Trap [] Description: Set or show SNMP traps destination. : IP address to send traps to.
PAGE 43
065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports Ratelimit Egress [] [enable|disable] [] Description: Set or show the egress configuration. [] [enable|disable] [] : Port list (default: All ports). : Enable or disable egress. : Disable or set leaky bucket rate in Kbit/s [128/256/512/1024/2048/3072k] (default: Show egress rate). Ratelimit Ingress[] [enable|disable] [] Description: Set or show the ingress configuration.