Specifications

B
MEDIA
CONVERTER
SYSTEM
TM
www.signamax-eu.com
B14
PART NO. DESCRIPTION FIBRE TYPE
065-1176ALFS 10/100BaseT/TX to 100BaseFX, SM/SC, 20 km, Tx=1,310 nm; Rx=1,550 nm Simplex SC Singlemode
065-1176BLFS 10/100BaseT/TX to 100BaseFX, SM/SC, 20 km, Tx=1,550 nm; Rx=1,310 nm Simplex SC Singlemode
065-1176AEDLFS 10/100BaseT/TX to 100BaseFX, SM/SC, 40 km, Tx=1,310 nm; Rx=1,550 nm Simplex SC Singlemode
065-1176BEDLFS 10/100BaseT/TX to 100BaseFX, SM/SC, 40 km, Tx=1,550 nm; Rx=1,310 nm Simplex SC Singlemode
065-11DINMT DIN rail mounting bracket for 065-11xx series media converters
Single Fibre WDM Media Converters (Fibre type: Simplex SC Singlemode)
Signamax Connectivity Systems’ Switching Single Fibre Wave Division Multiplexing (WDM) Media Converters
with Link Fault Signaling allow data typically carried over two strands of fibre optic cable to be carried over
a single strand of fibre optic cable, utilizing two different wavelengths to carry signals in both directions
simultaneously. This technology doubles the capacity of a company's fibre optic network, allowing a carrier
or an enterprise business to minimize its operational costs by eliminating or delaying the deployment of
additional fibre optic capacity. These converters are available in singlemode only, and span distances
of up to 40 kilometers (24.85 miles) with the 065-1176AEDLFS and 065-1176BEDLFS models.
Since WDM Switching Media Converters utilize two different wavelengths with one end of a circuit
transmitting on the other end’s receive frequency (and vice versa), they must be used in A/B pairs. A circuit
utilizing these converters would therefore use a single strand of singlemode fibre optic cable plus one each
of the 065-1176ALFS and 065-1176BLFS, or one each of the 065-1176AEDLFS and 065-1176BEDLFS and
065-1176BLFS, depending upon the distance spanned. All Signamax WDM converters are equipped with Link
Fault Signaling to provide the means for an SNMP-managed switch to recognize a failure on a fibre channel
or twisted-pair connection, enabling the switch to automatically route to a backup path if the connected
switch is equipped with Spanning Tree Algorithm. Each WDM Media Converter provides a 10/100BaseT/TX
auto-negotiating RJ45 twisted-pair connector port, and features store-and-forward switching architecture.
Auto-MDIX capability on the twisted-pair port is also provided for convenient connections.
Single Fibre WDM Converters
APPLICABLE STANDARDS
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.3u 100BaseFX
FIXED PORTS
1 Auto-MDIX twisted-pair port meeting IEEE 802.3
10BaseT & IEEE 802.3u 100BaseTX standard
specifications; Category 5 or better cable, 100 meters
maximum distance for 100BaseTX, Category 3 or better
cable, 100 meters maximum distance for 10BaseT
plus
1 WDM fibre optic port meeting IEEE 802.3u 100BaseFX
standard specification;
9/125 micron singlemode fibre optic cable, spanning
20 kilometers maximum distance (models 065-1176ALFS
and 065-1176BLFS) or
1 WDM fibre optic port meeting IEEE 802.3u 100BaseFX
standard specification;
9/125 micron singlemode fibre optic cable, spanning 40 kilometers
maximum distance (models 065-1176AEDLFS and 065-1176BEDLFS)
PERFORMANCE
Latency: < 4.2 µs (LIFO) Throughput @ 100Base: 148,809 pps (64-byte packets)
LEDs
Per unit: Power status, RJ45 port speed, Per Port: LNK/ACT, FDX/COL
Six LEDs total
PHYSICAL CHARACTERISTICS
Case dimensions (L x W x H): 110 x 81 x 23 mm (4.33 x 3.19 x 0.91")
Fibre optic interface varies with model.
Weight: 150 grams
USB power connector on the rear panel optionally powers converter from computer's USB port.
SAFETY
UL Listed
SPECIFICATIONS
Model 065-1176ALFS