Signamax™ Connectivity Systems Model 065-7727S 24-Port 10/100BaseT/TX Managed Switch User’s Guide
Signamax™ Connectivity Systems Model 065-7727S 24-Port 10/100BaseT/TX Managed Switch User’s Guide
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Table of Contents CAUTION ..............................................................................................................................................V ELECTRONIC EMISSION NOTICES .........................................................................................................V 1. Introduction ....................................................................................................................................
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-8-4. Port-based Group ..............................................................................................................79 3-8-5. Management VLAN............................................................................................................81 3-9. MAC TABLE ...............................................................................................................................82 3-10. GVRP CONFIGURATION ..............
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Revision History Release Date Revision 1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Caution Circuit devices are sensitive to static electricity, which can damage their delicate electronics. Dry weather conditions or walking across a carpeted floor may cause you to acquire a static electrical charge. To protect your device, always: • Touch the metal chassis of your computer to ground the static electrical charge before you pick up the circuit device. • Pick up the device by holding it on the left and right edges only.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch About this user’s manual In this user’s manual, it will not only tell you how to install and connect your network system but configure and monitor the 065-7727S through the built-in CLI and web by RS-232 serial interface and Ethernet ports step-by-step. Many explanation in detail of hardware and software functions are shown as well as the examples of the operation for web-based interface and command-line interface (CLI).
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 1. Introduction 1-1. Overview of 065-7727S 065-7727S, 24 Fast Ethernet + 2 Gigabit L2 Managed Switch, implemented 24 10/100Mbps TP + 2 Gigabit dual media ports with TP/SFP(or GBIC), is a standard switch that meets all IEEE 802.3/u/x/z Gigabit, Fast Ethernet and Ethernet specifications.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch • Key Features in the Device DHCP Option 82: This feature enables the Dynamic Host Configuration Protocol (DHCP) relay agent information (option 82) (065-7727S switch) to include information about itself and the attached client when forwarding DHCP requests from a DHCP client to a DHCP server via Trust Port. The DHCP server can use this information to assign IP addresses、gateway、subnet mask、DNS for each subscriber of a service-provider network.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 1-2. Checklist Before you start installing the switch, verify that the package contains the following: ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 065-7727S 24 Fast Ethernet + 2 Gigabit L2 Managed Switch Modules (optional) Mounting Accessory (for 19” Rack Shelf) This User's Manual in CD-ROM AC Power Cord RS-232 Cable Please notify your sales representative immediately if any of the aforementioned items is missing or damaged. 1-3.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch • Supports 802.1Q VLAN with 256 entries.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 1-4. View of 065-7727S Fig. 1-1 Full View of 065-7727S with SFP Module 1-4-1. User Interfaces on the Front Panel (Button, LEDs and Plugs) There are 24 TP Fast Ethernet ports and 2 slots for optional removable modules on the front panel of the switch. LED display area, locating on the front panel, contains a CPURUN, Power LED and 26 ports working status of the switch.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch • LED Indicators LED Color Function System LED CPURUN POWER ACT FDX SPD Green Green Green Green Green Lit when CPU is on and good Lit when AC power is on and good Lit when LEDSET set on active mode Lit when LEDSET set on full-duplex mode Lit when LEDSET set on speed mode 10/100Mbps Ethernet TP Port 1 to 24 LED LNK Lit when connection with remote device is good Off when cable connection is not good a.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 1-4-2. User Interfaces on the Rear Panel One RS-232 DB-9 interface is offered for configuration or management. And there is one AC power input socket for having the switch powered on or off. AC Line 100-240V 50/60 Hz RS-232 DB-9 Connector Fig. 1-3 Rear View of 065-7727S 1-5.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 1-4 Front View of 1000Base-SX/LX LC, SFP Fiber Transceiver Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 2. Installation 2-1. Starting 065-7727S Up This section will give users a quick start for: - Hardware and Cable Installation - Management Station Installation - Software booting and configuration 2-1-1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch • TP Port and Cable Installation ⇒ In the switch, TP port supports MDI/MDI-X auto-crossover, so both types of cable, straight-through (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 1, 2, 3, 6 in 10/100M TP; 1, 2, 3, 4, 5, 6, 7, 8 to 1, 2, 3, 4, 5, 6, 7, 8 in Gigabit TP) and crossed-over (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 3, 6, 1, 2) can be used. It means you do not have to tell from them, just plug it. ⇒ Use Cat.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 2-1-2. Installing Chassis to a 19-Inch Wiring Closet Rail Fig. 2-2 Caution: Allow a proper spacing and proper air ventilation for the cooling fan at both sides of the chassis. ⇒ ⇒ ⇒ Wear a grounding device for electrostatic discharge. Screw the mounting accessory to the front side of the switch (See Fig. 2-2). Place the Chassis into the 19-inch wiring closet rail and locate it at the proper position. Then, fix the Chassis by screwing it. 2-1-3.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch ⎯ Gigabit Fiber with multi-mode LC SFP module ⎯ Gigabit Fiber with single-mode LC SFP module ⎯ Gigabit Fiber with BiDi LC 1310nm SFP module ⎯ Gigabit Fiber with BiDi LC 1550nm SFP module The following table lists the types of fiber that we support and those else not listed here are available upon request. Multi-mode Fiber Cable and Modal Bandwidth Multi-mode 62.5/125μm IEEE 802.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch The fiber, TP cables and devices’ bit-time delay (round trip) are as follows: 1000Base-X TP, Fiber 100Base-TX TP Round trip Delay: 4096 100Base-FX Fiber Round trip Delay: 512 Cat. 5 TP Wire: 11.12/m Cat. 5 TP Wire: 1.12/m Fiber Cable : 10.10/m TP to fiber Converter: 56 Bit Time unit : 1ns (1sec./1000 Mega bit) Fiber Cable: 1.0/m Bit Time unit: 0.01μs (1sec.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch • Typical Network Topology in Deployment A hierarchical network with minimum levels of switch may reduce the timing delay between server and client station. Basically, with this approach, it will minimize the number of switches in any one path; will lower the possibility of network loop and will improve network efficiency.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 1. The same VLAN members could not be in different switches. 2. Every VLAN members could not access VLAN members each other. 3. The switch manager has to assign different names for each VLAN groups at one switch. Case 2b: Port-based VLAN (See Fig.2-5). Fig. 2-5 Port-based VLAN Diagram 1. VLAN1 members could not access VLAN2, VLAN3 and VLAN4 members. 2. VLAN2 members could not access VLAN1 and VLAN3 members, but they could access VLAN4 members. 3.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 2-1-4. Configuring the Management Agent of 065-7727S We offer you three ways to startup the switch management function. They are RS-232 console, CLI, and Web. Users can use any one of them to monitor and configure the switch. You can touch them through the following procedures.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3. Attaches the other end of the serial RS-232 DB-9 cable to PC’s serial port, running a terminal emulator supporting VT100/ANSI terminal with The switch’s serial port default settings. For example, Windows98/2000/XP HyperTerminal utility. Note: The switch’s serial port default settings are listed as follows: Baud rate 57600 Stop bits 1 Data bits 8 Parity N Flow control none 4. When you complete the connection, then press key.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 2-1-4-2. Configuring the Management Agent of 065-7727S through the Ethernet Port There are three ways to configure and monitor the switch through the switch’s Ethernet port. They are CLI, Web browser and SNMP manager. The user interface for the last one is NMS dependent and does not cover here. We just introduce the first two types of management interface. 065-7727S L2 Managed Switch Default IP Setting: IP = 192.168.1.1 Subnet Mask = 255.255.255.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 2-10 the Login Screen for Web 2-1-5. IP Address Assignment For IP address configuration, there are three parameters needed to be filled in. They are IP address, Subnet Mask, Default Gateway and DNS. IP address: The address of the network device in the network is used for internetworking communication. Its address structure looks is shown in the Fig. 2-11. It is “classful” because it is split into predefined address classes or categories.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch With the classful addressing, it divides IP address into three classes, class A, class B and class C. The rest of IP addresses are for multicast and broadcast. The bit length of the network prefix is the same as that of the subnet mask and is denoted as IP address/X, for example, 192.168.1.0/24. Each class has its address range described below. Class A: Address is less than 126.255.255.255.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Class D and E: Class D is a class with first 4 MSB (Most significance bit) set to 1-1-1-0 and is used for IP Multicast. See also RFC 1112. Class E is a class with first 4 MSB set to 1-1-1-1 and is used for IP broadcast. According to IANA (Internet Assigned Numbers Authority), there are three specific IP address blocks reserved and able to be used for extending internal network.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch In this diagram, you can see the subnet mask with 25-bit long, 255.255.255.128, contains 126 members in the sub-netted network. Another is that the length of network prefix equals the number of the bit with 1s in that subnet mask. With this, you can easily count the number of IP addresses matched. The following table shows the result. Prefix Length No. of IP matched No.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch For different network applications, the subnet mask may look like 255.255.255.240. This means it is a small network accommodating a maximum of 15 nodes in the network. Default gateway: For the routed packet, if the destination is not in the routing table, all the traffic is put into the device with the designated IP address, known as default router. Basically, it is a routing policy.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 2-2. Typical Applications The 065-7727S implements 24 Fast Ethernet TP ports with auto MDIX and 2 Gigabit dual media ports with SFP for removable module supported comprehensive fiber types of connection, including LC, BiDi LC for SFP. For more details on the specification of the switch, please refer to Appendix A. ⎯ ⎯ ⎯ The switch is suitable for the following applications. Central Site/Remote site application is used in carrier or ISP (See Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 2-14 Peer-to-peer Network Connection Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3. Operation of Web-based Management This chapter instructs you how to configure and manage the 065-7727S through the web user interface it supports, to access and manage the 24 10/100Mbps TP + 2 Gigabit dual media ports with TP/SFP(or GBIC)Fiber management Ethernet switch.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch In the switch, it supports a simple user management function allowing only one administrator to configure the system at the same time. If there are two or more users using administrator’s identity, the switch will allow the only one who logins first to configure the system. The rest of users, even with administrator’s identity, can only monitor the system. For those who have no administrator’s identity, can only monitor the system.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-1. Web Management Home Overview After you login, the switch shows you the system information as Fig. 3-2.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 3-3 port detail information In Fig. 3-3, it shows the basic information of the clicked port. With this, you’ll see the information about the port status, traffic status and bandwidth rating for egress and ingress respectively. ⎯ On the left-top corner, there is a pull-down list for Auto Logout. For the sake of security, we provide auto-logout function to protect you from illegal user as you are leaving.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Root System IP-MAC Binding Port Loop Detection SNMP DHCP Boot Multicast VLAN MAC Table GVRP STP Trunk 802.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-1-1. System Information Function name: System Information Function description: Show the basic system information. Parameter description: Model name: The model name of this device. System description: As it is, this tells what this device is. Here, it is “24 Fast Ethernet + 2 Gigabit L2 Managed Switch”. Location: Basically, it is the location where this switch is put. User-defined.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Host IP address: The IP address of the switch. Host MAC address: It is the Ethernet MAC address of the management agent in this switch. Device Port: Show all types and numbers of the port in the switch. RAM size: The size of the DRAM in this switch. Flash size: The size of the flash memory in this switch.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-1-2. IP Configuration IP configuration is one of the most important configurations in the switch. Without the proper setting, network manager will not be able to manage or view the device. The switch supports both manual IP address setting and automatic IP address setting via DHCP server. When IP address is changed, you must reboot the switch to have the setting taken effect and use the new IP to browse for web management and CLI management. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch IP address: Users can configure the IP settings and fill in new values if users set the DHCP function “Disable”. Then, click button to update. When DHCP is disabled, Default: 192.168.1.1 If DHCP is enabled, this field is filled by DHCP server and will not allow user manually set it any more.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch DNS: It is Domain Name Server used to serve the translation between IP address and name address. The switch supports DNS client function to re-route the mnemonic name address to DNS server to get its associated IP address for accessing Internet. User can specify a DNS IP address for the switch. With this, the switch can translate a mnemonic name address into an IP address. There are two ways to specify the IP address of DNS.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-1-3. Time Configuration The switch provides manual and automatic ways to set the system time via NTP. Manual setting is simple and you just input “Year”, “Month”, “Day”, “Hour”, “Minute” and “Second” within the valid value range indicated in each item. If you input an invalid value, for example, 61 in minute, the switch will clamp the figure to 59. NTP is a well-known protocol used to synchronize the clock of the switch system time over a network.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch NTP: NTP is Network Time Protocol and is used to sync the network time based Greenwich Mean Time (GMT). If use the NTP mode and select a built-in NTP time server or manually specify an user-defined NTP server as well as Time Zone, the switch will sync the time in a short after pressing button. Though it synchronizes the time automatically, NTP does not update the time periodically without user’s processing.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Day Light Saving End : This is used to set when to stop performing the daylight saving time. Mth: Range is 1 ~ 12. Default: 1 Day: Range is 1 ~ 31. Default: 1 Hour: Range is 0 ~ 23. Default: 0 Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-1-4. Account Configuration In this function, only administrator can create, modify or delete the username and password. Administrator can modify other guest identities’ password without confirming the password but it is necessary to modify the administrator-equivalent identity. Guest-equivalent identity can modify his password only.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-1-5. Management Security Through the management security configuration, the manager can do the strict setup to control the switch and limit the user to access this switch. The following rules are offered for the manager to manage the switch: Rule 1) : When no lists exists, then it will accept all connections.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Management Security Configuration Function description: The switch offers Management Security Configuration function. With this function, the manager can easily control the mode that the user connects to the switch. According to the mode, users can be classified into two types: Those who are able to connect to the switch (Accept) and those who are unable to connect to the switch (Deny).
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch IP Range: The switch supports two kinds of options for managed valid IP Range, including “Any” and “Custom”. Default is “Any”. In case that” Custom” had been chosen, you can assigned effective IP range. The valid range is 0.0.0.0~255.255.255.255. Incoming Port: The switch supports two kinds of options for managed valid Port Range, including “Any” and “Custom”. Default is “Any”.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-1-6. Virtual Stack Function name: Virtual Stack Function description: Virtual Stack Management(VSM) is the group management function. Through the proper configuration of this function, switches in the same LAN will be grouped automatically. And among these switch, one switch will be a master machine, and the others in this group will become the slave devices. VSM offers a simple centralized management function.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 3-8 Parameter description: State: It is used for the activation or de-activation of VSM. Default is Enable. Role: The role that the switch would like to play in virtual stack. Two types of roles, including master and slave are offered for option. Default is Master. Group ID: It is the group identifier (GID) which signs for VSM. Valid letters are A-Z, a-z, 0-9, “ - “ and “_” characters. The maximal length is 15 characters. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-1-7. DHCP Option 82 DHCP relay agent information option－Configuring the DHCP Option 82 Function name: DHCP Option 82 Function description: This feature enables the Dynamic Host Configuration Protocol (DHCP) relay agent information (option 82) (065-7727S switch) to include information about itself and the attached client when forwarding DHCP requests from a DHCP client to a DHCP server via Trust Port.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 3-10 Parameter description: State: It is used for the activation or de-activation of DHCP Option 82. Default is disable. Action: The Action that the switch would like to play in DHCP Option 82. tree types of action, including Replace , Keep and Drop are offered for option. Default is Replace. Trust Group: It is the Trust Group which signs for DHCP Option 82. When you enable the DHCP relay agent option 82 on the switch, these events occur: .
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-2. IP-MAC Binding The IP network layer uses a four-byte address. The Ethernet link layer uses a six-byte MAC address. Binding these two address types together allows the transmission of data between the layers. The primary purpose of IP-MAC binding is to restrict the access to a switch to a number of authorized users.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Binding List: The maximum number of IP-MAC binding client table is 512 entries. The maximum number of IP-MAC Binding server table is 64 entries. Name: A name is composed of any letter (A-Z, a-z) and digit (0-9) with maximal 8 characters. MAC: Six-byte MAC Address: xx-xx-xx-xx-xx-xx For example: 00-40-c7-00-00-01 IP: Four-byte IP Address: xxx.xxx.xxx.xxx For example: 192.168.1.100 Port No: Port no.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-3. Port Configuration Four functions, including Port Status, Port Configuration, Simple Counter and Detail Counter are contained in this function folder for port monitor and management. Each of them will be described in detail orderly in the following sections. Port Configuration Status Configuration Simple Counter Detail Counter 3-3-1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Port Status Function Description: Report the latest updated status of all ports in this switch. When any one of the ports in the switch changes its parameter displayed in the page, it will be automatically refreshed the port current status about every 5 seconds. Parameter Description: Port No: Display the port number. The number is 1 – 26. Both port 25 and 26 are optional modules. Media: Show the media type adopted in all ports.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Speed / Duplex : Display the speed and duplex of all port. There are three speeds 10Mbps, 100Mbps and 1000Mbps supported for TP media, and the duplex supported is half duplex and full duplex. If the media is 1Gbps fiber, it is 1000Mbps supported only. The status of speed/duplex mode is determined by 1) the negotiation of both local port and link partner in “Auto Speed” mode or 2) user setting in “Force” mode.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Parameter description of Port 25 and Port 26: Connector Type: Display the connector type, for instance, UTP, SC, ST, LC and so on. Fiber Type: Display the fiber mode, for instance, Multi-Mode, Single-Mode. Tx Central Wavelength: Display the fiber optical transmitting central wavelength, for instance, 850nm, 1310nm, 1550nm and so on. Baud Rate: Display the maximum baud rate of the fiber module supported, for instance, 10M, 100M, 1G and so on.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-3-2. Port Configuration Port Configuration is applied to change the setting of each port. In this configuration function, you can set/reset the following functions. All of them are described in detail below. Fig. 3-15 Function name: Port Configuration Function description: It is used to set each port’s operation mode. The switch supports 3 parameters for each port. They are State, Speed/Duplex and Flow Control.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch available for Fast Ethernet, Gigabit module in port 25, 26. If the media is 1Gbps fiber, it is always 1000Mbps and the duplex is full only. If the media is TP, the Speed/Duplex is comprised of the combination of speed mode, 10/100/1000Mbps, and duplex mode, full duplex and half duplex. The following table summarized the function the media supports.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-2-3. Simple Counter The function of Simple Counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad. In the Fig. 3-13, the window can show all ports’ counter information at the same time. Each data field has 20-digit long. If the counting is overflow, the counter will be reset and restart counting. The data is updated every time interval defined by the user.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Rx Packet: The counting number of the packet received. Tx Collision: Number of collisions transmitting frames experienced. Rx Error Packet: Number of bad packets received.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-3-4. Detail Counter The function of Detail Counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad. In the Fig. 3-14, the window can show only one port counter information at the same time. To see another port’s counter, you have to pull down the list of Select, then you will see the figures displayed about the port you had chosen. Each data field has 20-digit long.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Rx Unicast Packets: Show the counting number of the received unicast packet. Rx Broadcast Packets: Show the counting number of the received broadcast packet. Rx Multicast Packets: Show the counting number of the received multicast packet. Rx Pause Packets: Show the counting number of the received pause packet. Tx Collisions: Number of collisions transmitting frames experienced.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Number of 1024-1522-byte frames in good and bad packets received. Tx Packets: The counting number of the packet transmitted. TX Octets: Total transmitted bytes. Tx Unicast Packets: Show the counting number of the transmitted unicast packet. Tx Broadcast Packets: Show the counting number of the transmitted broadcast packet. Tx Multicast Packets: Show the counting number of the transmitted multicast packet.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-4. Loop Detection The loop detection is used to detect the presence of traffic. When switch receives packet’s(looping detection frame) MAC address the same as oneself from port, show Loop detection happens. The port will be locked when it received the looping detection frames.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-5. SNMP Configuration Any Network Management System (NMS) running the Simple Network Management Protocol (SNMP) can manage the Managed devices equipped with SNMP agent, provided that the Management Information Base (MIB) is installed correctly on the managed devices.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Default SNMP function : Enable Default community name for GET: public Default community name for SET: private Default community name for Trap: public Default Set function : Enable Default trap host IP address: 0.0.0.0 Default port number :162 Trap: In the switch, there are 6 trap hosts supported. Each of them has its own community name and IP address; is user-definable.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-6. DHCP Boot The DHCP Boot function is used to spread the request broadcast packet into a bigger time frame to prevent the traffic congestion due to broadcast packets from many network devices which may seek its NMS, boot server, DHCP server and many connections predefined when the whole building or block lose the power and then reboot and recover.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-7. Multicast The function, is used to establish the multicast groups to forward the multicast packet to the member ports, and, in nature, avoids wasting the bandwidth while IP multicast packets are running over the network. This is because a switch that does not support IGMP or IGMP Snooping can not tell the multicast packet from the broadcast packet, so it can only treat them all as the broadcast packet.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-7-1. IGMP Setting Function name: IGMP Setting Function description: IGMP is used to snoop the status of IP multicast groups and display its associated information in both tagged VLAN and non-tagged VLAN networks. Enabling IGMP with either passive or active mode, you can monitor the IGMP snooping information, which contains the multicast member list with the multicast groups, VID and member port.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Specific Query Max Response Time : To set the specific Query Response Time field is used in specific or group-specific query messages. The Specific Maximum Response Time is configured as the value. Available value: 1-10 sec Specific Query Timeout : The Specific Query Timeout field is the amount of time in seconds. Available value: 1-30 sec 3-7-2.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-7-3. MVR Setting Function name: MVR Setting Function description: Multicast VLAN Registration (MVR) routes packets received in a multicast source VLAN to one or more receive VLANs. Clients are in the receive VLANs and the multicast server is in the source VLAN. Multicast routing has to be disabled when MVR is enabled. Refer to the configuration guide at Understanding Multicast VLAN Registration for more information on MVR..
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-7-4. Group Filtering Function name: Group Filtering Function description: The Group Filtering function allows the Multicast VLAN Registration to set up the IP multicast group filtering conditions. IGMP join behavior that meet the items you set up will be joined or formed the multicast group. Fig. 3-24 Parameter description: IP Address Range: The switch supports two kinds of options for managed valid IP range, including “Any” and “Custom”.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Add: A new entry of allowed group configuration can be created after the parameters as mentioned above had been setup and then press button. Edit: The existed entry also can be modified after pressing button. Delete: Remove the existed entry of allowed group configuration from the allowed group.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-8. VLAN The switch supports Tag-based VLAN (802.1q) and Port-based VLAN. Support 256 active VLANs and VLAN ID 1~4094. VLAN configuration is used to partition your LAN into small ones as your demand. Properly configuring it, you can gain not only improving security and increasing performance but greatly reducing VLAN management. 3-8-1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Symmetric Vlan: This is a Ingress Rule (Rule 1, The Ingress Filtering Rule 1 is “forward only packets with VID matching this port’s configured VID”.). For example, if port 1 receives a tagged packet with VID=100 (VLAN name=VLAN100), and if Symmetric-Vlan function is enabled, the switch will check if port 1 is a member of VLAN100. If yes, the received packet is forwarded; otherwise, the received packet is dropped.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 3-25 3-8-2. Tag-based Group Function name: Tag-based Group Configuration Function description: It shows the information of existed Tag-based VLAN Groups. You can also easily create, edit and delete a Tag-based VLAN group by pressing , and function buttons. User can add a new VLAN group by inputting a new VLAN name and VLAN ID after pressing button.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 3-26 Add Group: Input the VLAN name, VID and then choose the member by ticking the check box beside the port No. to create a new Tag-based VLAN. As to the parameter of Untag, it stands for an egress rule of the port. If you tick the check box beside the port No., packets with this VID outgoing from this port will be untagged. Finally, press the button to have the setting taken effect. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Delete Group: Just press the button to remove the selected group entry from the Tag-based group table. Fig. 3-28 Edit a group: Just select a group entry and press the button, then you can modify a group’s description, member and untag settings.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-8-3. PVID Function name: PVID Function description: In PVID Setting, user can input VID number to each port. The range of VID number is from 1 to 4094. User also can choose ingress filtering rule (Rule 2) to each port. The Ingress Filtering Rule 2 is “drop untagged frame”. While Rule 2 is enabled, the port will discard all Untagged-frames. Fig. 3-29 Parameter description: Port 1-26: Port number. PVID: This PVID range will be 1-4094.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Drop Untag: Drop untagged frame. You can configure a given port to accept all frames (Tagged and Untagged) or just receive tagged frame. If the former is the case, then the packets with tagged or untagged will be processed. If the later is the case, only the packets carrying VLAN tag will be processed, the rest packets will be discarded. 3-8-4.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Add Group: Create a new Port-based VLAN. Input the VLAN name and choose the member by ticking the check box beside the port No., then, press the button to have the setting taken effect. Fig. 3-31 Delete Group: Just press the button to remove the selected group entry from the Port-based group table. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Edit a group: Just select a group entry and press the button, then you can modify a group‘s description and member set. 3-8-5. Management VLAN Function name: Management VLAN Function Description: Fig. 3-33 Parameter description: State: It works when the tag-based mode is chosen. When this function is enabled, only the tagged packets with this VID can manage the switch. VID: Valid range 1~4094.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-9. MAC Table MAC Table Configuration gathers many functions, including MAC Table Information, MAC Table Maintenance, Static and MAC Alias, which cannot be categorized to some function type. They are described below. Function name: MAC Table Information Function Description: Display the static or dynamic learning MAC entry and the state for the selected port. Parameter description: Port: Select the port you would like to inquire.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Port: The port that exists in the searched MAC Entry. VID: VLAN Group that MAC Entry exists. State: Display the method that this MAC Entry is built. It may show “Dynamic MAC” or “Static MAC”. Fig. 3-34 Function Name: MAC Table Maintenance Function Description: This function can allow the user to set up the processing mechanism of MAC Table. An idle MAC address exceeding MAC Address Age-out Time will be removed from the MAC Table.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Delete a MAC address idling for a period of time from the MAC Table, which will not affect static MAC address. Range of MAC Address Aging Time is 10-1000000 seconds. The default Aging Time is 300 seconds. Learning Limit: To set up the maximum amount of MAC that each port can learn. Valid value of learning limit for port 1~24 ranges from 0-8191.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 3-36 Parameter description: MAC: It is a six-byte long Ethernet hardware address and usually expressed by hex and separated by hyphens. For example, 00 – 40 - C7 - D6 – 00 - 01 VID: VLAN identifier. This will be filled only when tagged VLAN is applied. Valid range is 1 ~ 4094. Queue (Priority): Set up the priority( 0~3) for the MAC.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: MAC Alias Function description: MAC Alias function is used to let you assign MAC address a plain English name. This will help you tell which MAC address belongs to which user in the illegal access report. At the initial time, it shows all pairs of the existed alias name and MAC address. There are three MAC alias functions in this function folder, including MAC Alias Add, MAC Alias Edit and MAC Alias Delete.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Parameter description: MAC Address: It is a six-byte long Ethernet hardware address and usually expressed by hex and separated by hyphens. For example, 00 – 40 - C7 - D6 – 00 - 02 Alias: MAC alias name you assign. Note: If there are too many MAC addresses learned in the table, we recommend you inputting the MAC address and alias name directly.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-10. GVRP Configuration GVRP is an application based on Generic Attribute Registration Protocol (GARP), mainly used to automatically and dynamically maintain the group membership information of the VLANs. The GVRP offers the function providing the VLAN registration service through a GARP application.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch can pull down the list and click the arrow key to choose “Enable” or “Disable”. Then, click the button, the system will take effect immediately. Join Time: Used to declare the Join Time in unit of centisecond. Valid time range: 20 –100 centisecond, Default: 20 centisecond. Leave Time: Used to declare the Leave Time in unit of centisecond. Valid time range: 60 –300 centisecond, Default: 60 centisecond.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch received GVRP PDU. There are two modes, disable and enable, provided for the user’s choice. Disabled: In this mode, the switch dynamic VLAN will be created when this port received GVRP PDU. The default setting is Normal. Enabled: In this mode, the switch does not create dynamic VLAN when this port received GVRP PDU.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: GVRP Counter Function description: All GVRP counters are mainly divided into Received and Transmitted two categories to let you monitor the GVRP actions. Actually, they are GARP packets. Fig. 3-39 Parameter description: Received: Total GVRP Packets: Total GVRP BPDU is received by the GVRP application. Invalid GVRP Packets: Number of invalid GARP BPDU is received by the GARP application.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch LeaveEmpty Message Packets: Number of GARP BPDU with Leave Empty message is received by the GARP application. Empty Message Packets: Number of GARP BPDU with Empty message is received by the GARP application. Transmitted: Total GVRP Packets: Total GARP BPDU is transmitted by the GVRP application. Invalid GVRP Packets: Number of invalid GARP BPDU is transmitted by the GVRP application.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: GVRP Group Information Function description: To show the dynamic group member and their information. Parameter description: Current Dynamic Group Number: The number of GVRP group that are created currently. VID: VLAN identifier. When GVRP group creates, each dynamic VLAN group owns its VID. Valid range is 1 ~ 4094. Member Port: Those are the members belonging to the same dynamic VLAN group.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-11. STP Configuration The Spanning Tree Protocol (STP) is a standardized method (IEEE 802.1D) for avoiding loops in switched networks. When STP is enabled, ensure that only one path is active between any two nodes on the network at a time. User can enable Spanning Tree Protocol on switch’s web management and then set up other advanced items. We recommend that you enable STP on all switches to ensure a single active path on the network. 3-11-1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch All bridges in the LAN will re-learn and determine which the root bridge is. Maximum Age time is assigned by root bridge in unit of seconds. Default is 20 seconds. Current Forward Delay: Show the current root bridge forward delay time. The value of Forward Delay time is set by root. The Forward Delay time is defined as the time spent from Listening state moved to Learning state or from Learning state moved to Forwarding state of a port in bridge.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-11-2. STP Configuration The STP, Spanning Tree Protocol, actually includes RSTP. In the Spanning Tree Configuration, there are six parameters open for the user to configure as user’s idea. Each parameter description is listed below.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Forward Delay: You can set the root bridge forward delay time. This figure is set by root bridge only. The forward delay time is defined as the time spent from Listening state moved to Learning state and also from Learning state moved to Forwarding state of a port in bridge. The forward delay time contains two states, Listening state to Learning state and Learning state to Forwarding state.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-11-3. STP Port Configuration Function name: STP Port Setting Function description: In the STP Port Setting, one item selection and five parameters settings are offered for user’s setup. User can disable and enable each port by selecting each Port Status item. User also can set “Path Cost” and “Priority” of each port by filling in the desired value and set “Admin Edge Port” and “Admin Point To Point” by selecting the desired item.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 802.1w RSTP recommended value: (Valid range: 1 – 200,000,000) 10 Mbps : 2,000,000 100 Mbps : 200,000 1 Gbps : 20,000 Default: 0 Priority: Priority here means Port Priority. Port Priority and Port Number are mixed to form the Port ID. Port IDs are often compared in order to determine which port of a bridge would become the Root Port. The range is 0 – 240. Default is 128. Admin Edge Port: If user selects “Yes”, this port will be an edge port.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch M Check: Migration Check. It forces the port sending out an RSTP BPDU instead of a legacy STP BPDU at the next transmission. The only benefit of this operation is to make the port quickly get back to act as an RSTP port. Click button to send a RSTP BPDU from the port you specified. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-12. Trunking Configuration The Port Trunking Configuration is used to configure the settings of Link Aggregation. You can bundle more than one port with the same speed, full duplex and the same MAC to be a single logical port, thus the logical port aggregates the bandwidth of these ports. This means you can apply your current Ethernet equipments to build the bandwidth aggregation.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Per Trunking Group supports a maximum of 4 ready member-ports. Please note that some decisions will automatically be made by the system while you are configuring your trunking ports.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Port Setting/Status Function description: Port setting/status is used to configure the trunk property of each and every port in the switch system. Parameter description: Method: This determines the method a port uses to aggregate with other ports. None: A port does not want to aggregate with any other port should choose this default setting. LACP: A port use LACP as its trunk method to get aggregated with other ports also using LACP.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Aggtr: Aggtr is an abbreviation of “aggregator”. Every port is also an aggregator, and its own aggregator ID is the same as its own Port No. We can regard an aggregator as a representative of a trunking group. Ports with same Group ID and using same trunking method will have the opportunity to aggregate to a particular aggregator port. This aggregator port is usually the port with the smallest Port No. within the trunking group.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Aggregator View Function description: To display the current port trunking information from the aggregator point of view. Parameter description: Aggregator: It shows the aggregator ID (from 1 to 26) of every port. In fact, every port is also an aggregator, and its own aggregator ID is the same as its own Port No.. Method: Show the method a port uses to aggregate with other ports.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: LACP Detail (LACP Aggregator Detailed Information) Function description: Show the detailed information of the LACP trunking group. Parameter description: Actor: The switch you are watching on. Partner: The peer system from this aggregator’s view. System Priority: Show the System Priority part of a system ID. MAC Address: Show the MAC Address part of a system ID. Port: Show the port number part of an LACP port ID.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: LACP System Configuration Function description: It is used to set the priority part of the LACP system ID. LACP will only aggregate together the ports whose peer link partners are all on a single system. Each system supports LACP will be assigned a globally unique System Identifier for this purpose. A system ID is a 64-bit field comprising a 48-bit MAC Address and 16-bit priority value.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-13. 802.1x Configuration 802.1x port-based network access control provides a method to restrict users to access network resources via authenticating user’s information. This restricts users from gaining access to the network resources through a 802.1x-enabled port without authentication. If a user wishes to touch the network through a port under 802.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch The overview of operation flow for the Fig. 3-41 is quite simple. When Supplicant PAE issues a request to Authenticator PAE, Authenticator and Supplicant exchanges authentication message. Then, Authenticator passes the request to RADIUS server to verify. Finally, RADIUS server replies if the request is granted or denied.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Authentication server C Fig. 3-49 Authenticator B Supplicant A The Fig. 3-49 shows the procedure of 802.1x authentication. There are steps for the login based on 802.1x port access control management. The protocol used in the right side is EAPOL and the left side is EAP. 1. At the initial stage, the supplicant A is unauthenticated and a port on switch acting as an authenticator is in unauthorized state. So the access is blocked in this stage. 2.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 8. If user ID and password is correct, the authentication server will send a Radius-Access-Accept to the authenticator. If not correct, the authentication server will send a Radius-Access-Reject. 9. When the authenticator PAE receives a Radius-Access-Accept, it will send an EAP-Success to the supplicant. At this time, the supplicant is authorized and the port connected to the supplicant and under 802.1x control is in the authorized state.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Only MultiHost 802.1X is the type of authentication supported in the switch. In this mode, for the devices connected to this port, once a supplicant is authorized, the devices connected to this port can access the network resource through this port. 802.1x Port-based Network Access Control function supported by the switch is little bit complex, for it just support basic Multihost mode, which can distinguish the device’s MAC address and its VID.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: 802.1x State Setting Function description: This function is used to configure the global parameters for RADIUS authentication in 802.1x port security application. Parameter description: Radius Server: RADIUS server IP address for authentication. Default: 192.168.1.1 Port Number: The port number to communicate with RADIUS server for the authentication service. The valid value ranges 1-65535. Default port number is 1812.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: 802.1x Mode Setting Function description: Set the operation mode of 802.1X for each port. In this device, it supports only Multi-host operation mode. Parameter description: Port Number: Indicate which port is selected to configure the 802.1x operation mode. 802.1x Mode: 802.1x operation mode. There are two options, including Disable and Multi-host mode. Default is Disable.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Port Security Management Function description: Shows each port status. In Multihost mode, it shows the port number and its status, authorized or unauthorized. Parameter description: Disable Mode: When selecting Disable mode for a port in the function 802.1X Port Mode Configuration, the port is in the uncontrolled port state and does not apply 802.1X authenticator on it.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Param. Setting Function description: This function is used to configure the parameters for each port in 802.1x port security application. Refer to the following parameters description for details. Parameter description: Port: It is the port number to be selected for configuring its associated 802.1x parameters which are Port control, reAuthMax, txPeriod, Quiet Period, reAuthEnabled, reAuthPeriod, max.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch reAuthEnabled: Choose whether regular authentication will take place in this port. Default: ON reAuthPeriod(1-65535 s): A non-zero number seconds between the periodic re-authentication of the supplicant. Default: 3600 max. Request(1-10): The maximum of number times that the authenticator will retransmit an EAP Request to the supplicant before it times out the authentication session. The valid range: 1 – 10.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-14. Alarm Configuration Alarm Configuration Events Configuration Email/SMS Function name: Events Configuration Function description: The Trap Events Configuration function is used to enable the switch to send out the trap information while pre-defined trap events occurred. The switch offers 21 different trap events to users for switch management.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Email/SMS Configuration Function description: Alarm configuration is used to configure the persons who should receive the alarm message via either email or SMS, or both. It depends on your settings. An email address or a mobile phone number has to be set in the web page of alarm configuration (See Fig. 3-49). Then, user can read the trap information from the email or the mobile phone.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-15. Configuration The switch supports three copies of configuration, including the default configuration, working configuration and user configuration for your configuration management. All of them are listed and described below respectively. Default Configuration: This is Rubytech’s setting and cannot be altered. In Web UI, two restore default functions are offered for the user to restore to the default setting of the switch.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-15-1. Save/Restore Function name: Save As Start Configuration Function description: Save the current configuration as a start configuration file in flash memory. Fig. 3-58 Function name: Save As User Configuration Function description: Save the current configuration as a user configuration file in flash memory. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Restore Default Configuration (includes default IP address) Function description: Restore Default Configuration function can retrieve Rubytech’s setting to replace the start configuration. And the IP address of the switch will also be restored to 192.168.1.1. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Restore User Configuration Function description: Restore User Configuration function can retrieve the previous confirmed working configuration stored in the flash memory to update start configuration. When completing to restore the configuration, the system’s start configuration is updated and will be changed its system settings after rebooting the system. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-15-2. Config File Function name: Config File Function description: With this function, user can back up or reload the config files of Save As Start or Save As User via TFTP. Parameter description: Export File Path: Export Start: Export Save As Start’s config file stored in the flash. Export User-Conf: Export Save As User’s config file stored in the flash. Import File Path: Import Start: Import Save As Start’s config file stored in the flash.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-16. Security Function name: Mirror Configuration Function description: Mirror Configuration is to monitor the traffic of the network. For example, we assume that Port A and Port B are Monitoring Port and Monitored Port respectively, thus, the traffic received by Port B will be copied to Port A for monitoring. Parameter description: Mode: Used for the activation or de-activation of Port Mirror function. Default is disable.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Isolated Group Function description: Isolated Group function can let the port be independent of other ports in the Isolated group, and the communication is also forbidden between these ports. But, the ports of the Isolated group are still able to communicate with the ports of the non-Isolated group.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-17. Bandwidth Management Function name: Ingress Bandwidth Setting Function description: Ingress Bandwidth Setting function is used to set up the limit of Ingress bandwidth for each port. Fig. 3-66 Parameter description: Port No.: Choose the port that you would like this function to work on it. Valid range of the port is 1~26. Rate: Set up the limit of Ingress bandwidth for the port you choose.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Egress Bandwidth Setting Function description: Egress Bandwidth Setting function is used to set up the limit of Egress bandwidth for each port. Fig. 3-67 Parameter description: Port No.: Choose the port that you would like this function to work on it. Valid range of the port is 1~26. Rate: Set up the limit of Egress bandwidth for the port you choose.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Storm Function description: Bandwidth Management function is used to set up the limit of Ingress and Egress bandwidth for each port. Fig. 3-68 Parameter description: Storm Type: Disable: Disable the function of the bandwidth storm control. BC (Broadcast Storm Control): Enable the function of bandwidth storm control for broadcast packets.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch multicast Storm packets in transmission. UC, MC (Unknown Unicast, Multicast Storm Control): Enable the function of bandwidth storm control for Unknown Unicast and multicast Storm packets in transmission. BC, UC, MC (Broadcast, Unknown Unicast, Multicast Storm Control): Enable the function of bandwidth storm control for all packets in transmission. Rate : Set up the limit of bandwidth for storm type you choose.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-18. QoS(Quality of Service) Configuration The switch supports 5 kinds of QoS, are as follows, MAC Priority, 802.1p Priority, IP TOS Priority, and DiffServ DSCP Priority. Port Based Priority has a special name called VIP Port in the switch. Any packets enter VIP Port will have highest transmitting priority. MAC Priority act on the destination address of MAC in packets. VLAN tagged Priority field is effected by 802.1p Priority setting.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch The QoS functions as we mentioned above are able to enabled at the same time. But, the following precedence will decide whether these functions work or not. 1. Enable both VIP and TOS. Choose priorities of VIP and TOS. 2. Enable both VIP and DSCP. Choose priorities of VIP and DSCP. 3. Enable both TOS and DSCP. Choose "DSCP". 4. Enable both VIP and DSCP. Choose priorities of VIP and DSCP. 5. Enable both 802.1p and TOS. Choose "TOS". 6.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: 802.1p Setting Function description: This function will affect the priority of VLAN tag. Based on priority of VLAN tag, it can arrange 0~8 priorities, priorities can map to 4 queues of the switch (queue 0~3) and possess different bandwidth distribution according to your weight setting. Parameter description: 802.1p Priority Mapping: Each Priority can select any of Queue 0 ~ Queue 3.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: DSCP Setting Function description: In the late 1990s, the IETF redefined the meaning of the 8-bit SERVICE TYPE field to accommodate a set of differentiated services (DS). Under the differentiated services interpretation, the first six bits comprise a codepoint, which is sometimes abbreviated DSCP, and the last two bits are left unused.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-19. ACL The 065-7727S switch access control list (ACL) is probably the most commonly used object in the IOS. It is used for packet filtering but also for selecting types of traffic to be analyzed, forwarded, or influenced in some way. The ACLs are divided into EtherTypes. IPv4, ARP protocol, MAC and VLAN parameters etc. Here we will just go over the standard and extended access lists for TCP/IP.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Parameter description: Add To add new access control rule on switch. You must configure the parameters what described later when you add the new access control rule. Edit/ Show: To modify or monitor the access control configuration rule on switch. Delete: To delete existed access control rule on switch. Fig. 3-73 ACL Configuration: To add a new ACL rule on switch.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 3-74 VLAN Tag: To input VLAN Type with 2 type include “any” and “ Tag-based Vlan” If you choice Tag-based Vlan type then you must input Tag VID in field and droll the Tag Priority bar to choice the tag priority from 0 to 7. Fig. 3-75 Ethernet Type: Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch To droll “Ethernet Type” bar and option “any”, “ IPv4”, “ ARP” and “ Specific” for ACL requirement. Any: IPv4: ARP: Specific: It is including all frame type It is including all IPv4 protocol frame type It is including all ARP protocol frame type It is specific frame type Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch IPv4 TOS : To droll the bar and you can elect “ Any”, and “ Specific”. If you click “ Specific” then you need to set the TOS Value to filter. Fig. 3-79 Fig. 3-80 TTL Range : To droll the bar and you can elect “ TTL=0”, “TTL=1”, “TTL=2-254” and “ TTL=255” and set the Time to live value range. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch IPv4 DA/ SA : To droll the bar and you can elect “ Any”, “HOST” and “Network”. Fig. 3-82 L4 Destination port : To droll the bar and you can elect “ Any” and “Specific”. If you click “specific” then you need to set destination port value. Fig. 3-83 Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch L4 Source port : To droll the bar and you can elect “ Any” and “Specific”. If you click “specific” then you need to set source port value. Fig. 3-85 Fig. 3-86 Action: To set network packet filter includes “In-band” , “Out-band” and “Modify Packet for In/Out-Band”.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 3-87 Fig. 3-88 Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 3-90 Fig. 3-91 Modify Packet for In/ Out-Band : Modify Packet -802.1P: To droll down the bar to elect “Any” and “Specific”. If you click the “ Specific” then you need to set 802.1p value in the field. default is 0 Fig. 3-92 Modify Packet -QOS: To droll down the bar to elect “Any” and “Specific”. If you click the “ Specific” then you need to set QoS value in the field. default is 0 Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Rate Meter: To set rate meter function with the bandwidth parameter. The range is 64 to 1024000kbps. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3- 20. Diagnostics Five functions, including Diagnostics, Loopback Test, Ping Test, Auto Ping and Cable are contained in this function folder for device self-diagnostics. Each of them will be described in detail orderly in the following sections. Diagnostics Diag Loopback Test Ping Test Auto Ping Cable Function name: Diag Function description: Diagnostics function provides a set of basic system diagnosis.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Loopback Test Function description: In the Loopback Test function, there are two different loopback tests. One is Internal Loopback Test and the other is External Loopback Test. The former test function will not send the test signal outside the switch box. The test signal only wraps around in the switch box. As to the latter test function, it will send the test signal to its link partner.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Ping Test Function description: Ping Test function is a tool for detecting if the target device is alive or not through ICMP protocol which abounds with report messages. The switch provides Ping Test function to let you know that if the target device is available or not. You can simply fill in a known IP address and then click button.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Auto Ping Function description: Auto Ping function is a tool for detecting if the target device is alive or not through ICMP protocol which abounds with report messages. The switch provides auto Ping Test function to let you know that if the target device is available or not. Parameter description: IP Address: An IP address with the version of v4, e.g. 192.168.1.1. Interval: Range is 1 ~300 sec. Times: Range is 3 ~100 Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Function name: Cable Function description: Cable function is a tool for detecting if the cable per port status is OK or not. report messages. The switch provides cable Test function to let you know that if the cable connect to a port is OK or not. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3- 21. TFTP Server Function name: TFTP Server Function description: Set up IP address of TFTP server. Parameter description: Specify the IP address where the TFTP server locates. Fill in the IP address of your TFTP server, then press button to have the setting taken effect. Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-22. Log This function shows the log data. The switch provides system log data for users. There are 16 private trap logs, 5 public trap logs. The switch supports total 120 log entries. For more details on log items, please refer to the section of Trap/Alarm Configuration and SNMP Configuration.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Upload Log: Upload log data through tftp. Clear Log: Clear log data.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-23. Firmware Upgrade Software upgrade tool is used to help upgrade the software function in order to fix or improve the function. The switch provides a TFTP client for software upgrade. This can be done through Ethernet. Function name: Firmware Upgrade Function description: The switch supports TFTP upgrade tool for upgrading software. If you assure to upgrade software to a newer version one, you must follow two procedures: 1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-24. Reboot We offer you many ways to reboot the switch, including power up, hardware reset and software reset. You can press the RESET button in the front panel to reset the switch. After upgrading software, changing IP configuration or changing VLAN mode configuration, then you must reboot to have the new configuration taken effect. Here we are discussing is software reset for the “reboot” in the main menu.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 3-25. Logout You can manually logout by performing Logout function. In the switch, it provides another way to logout. You can configure it to logout automatically. Function name: Logout Function description: The switch allows you to logout the system to prevent other users from the system without the permission. If you do not logout and exit the browser, the switch will automatically have you logout.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 4. Operation of CLI Management 4-1. CLI Management Refer to Chapter 2 for basic installation. The following description is the brief of the network connection. -- Locate the correct DB-9 null modem cable with female DB-9 connector. Null modem cable comes with the management switch. Refer to the Appendix B for null modem cable configuration. -- Attach the DB-9 female connector to the male DB-9 serial port connector on the Management board.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Fig. 4-1 Fig.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 4-2. Commands of CLI To see the commands of the mode, please input “?” after the prompt, then all commands will be listed in the screen. All commands can be divided into two categories, including global commands and local commands. Global commands can be used wherever the mode you are. They are “exit”, “end”, “help”, “history”, “logout”, “save start”, “save user”, “restore default” and “restore user”. For more details, please refer to Section 4-2-1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 4-2-1. Global Commands of CLI end Syntax: end Description: Back to the top mode. When you enter this command, your current position would move to the top mode. If you use this command in the top mode, you are still in the position of the top mode. Argument: None. Possible value: None. Example: 065-7727S # alarm 065-7727S (alarm)# events 065-7727S (alarm-events)# end 065-7727S # exit Syntax: exit Description: Back to the previous mode.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch help Syntax: help Description: To show available commands. Some commands are the combination of more than two words. When you enter this command, the CLI would show the complete commands. Besides, the command would help you classify the commands between the local commands and the global ones. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch history Syntax: history [#] Description: To show a list of previous commands that you had ever run. When you enter this command, the CLI would show a list of commands which you had typed before. The CLI supports up to 256 records. If no argument is typed, the CLI would list total records up to 256. If optional argument is given, the CLI would only show the last numbers of records, given by the argument.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch logout Syntax: logout Description: When you enter this command via Telnet connection, you would logout the system and disconnect. If you connect the system through direct serial port with RS-232 cable, you would logout the system and be back to the initial login prompt when you run this command. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch restore user Syntax: restore user Description: To restore the startup configuration as user defined configuration. If restoring default successfully, the CLI would prompt if reboot immediately or not. If you press Y or y, the system would reboot immediately; others would back to the CLI system. After restoring user-defined configuration, all the changes in the startup configuration would be lost.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch save user Syntax: save user Description: To save the current configuration as the user-defined configuration. When you enter this command, the CLI would save your current configuration into the non-volatile FLASH as user-defined configuration. Argument: None. Possible value: None. Example: 065-7727S # save user Saving user...
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 4-2-2. Local Commands of CLI 802.1x set quiet-period Syntax: set quiet-period Description: A timer used by the Authenticator state machine to define periods of time during when it will not attempt to acquire a Supplicant. Argument: : syntax 1,5-7, available from 1 to 26 : timer, range 0-65535 Possible value: : 1 to 26 : 0-65535, default is 60 Example: 065-7727S (802.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch : 1 to 26 : 1-10, default is 2 Example: 065-7727S (802.1x)# set reAuthMax 2 2 set reAuthPeriod Syntax: set reAuthPeriod Description: A constant that defines a nonzero number of seconds between periodic reauthentication of the supplicant.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch : the service port of Radius Server(Authorization port), range 1~65535 : set up the value of secret-key, and the length of secret-key is from 1 to 31 : 0 for disable, 1 for enable : xxx.xxx.xxx.xxx :1~65535 Possible value: : 1~65535, default 1812 : 0 for disable, 1 for enable : xxx.xxx.xxx.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Description: A timer used by the Authenticator PAE state machine to determine when an EAPOL PDU is to be transmitted. Argument: : syntax 1,5-7, available from 1 to 26 : timer, range 1-65535 Possible value: : 1 to 26 : 1-65535, default is 30 Example: 065-7727S (802.1x)# set txPeriod 2 30 show mode Syntax: show mode Description: To display the mode of each port. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Argument: None. Possible value: None. Example: 065-7727S(802.1x)# show parameter port 1) port control : Auto reAuthMax : 2 txPeriod : 30 Quiet Period : 60 reAuthEnabled : ON reAuthPeriod : 3600 max. Request : 2 suppTimeout : 30 serverTimeout : 30 : : : show security Syntax: show security Description: To display the authentication status of each port. Argument: None. Possible value: None. Example: 065-7727S (802.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show state Syntax: show state Description: To display the Radius server configuration. Argument: None. Possible value: None. Example: 065-7727S (802.1x)# show state Radius Server: 192.168.1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch account add Syntax: add Description: To create a new guest user. When you create a new guest user, you must type in password and confirm password. Argument: : new account name Possible value: : A string must be at least 5 character. Example: 065-7727S(account)# add aaaaa Password: Confirm Password: 065-7727S(account)# del Syntax: del Description: To delete an existing account.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch modify Syntax: modify Description: To change the username and password of an existing account. Argument: : existing user account Possible value: None. Example: 065-7727S(account)# modify aaaaa username/password: the length is from 5 to 15. Current username (aaaaa):bbbbb New password: Confirm password: Username changed successfully. Password changed successfully.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch alarm <> del mail-address Syntax: del mail-address <#> Description: To remove the e-mail address. Argument: <#>: email address number, range: 1 to 6 Possible value: <#>: 1 to 6 Example: 065-7727S(alarm-email)# del mail-address 2 del server-user Syntax: del server-user Description: To remove the server, user account and password. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set server Syntax: set server Description: To set up the IP address of the email server. Argument: :email server ip address or domain name Possible value: None. Example: 065-7727S(alarm-email)# set server 192.168.1.6 set user Syntax: set user Description: To set up the account of the email server. Argument: : email server account Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch <> del all Syntax: del all Description: To disable email, sms and trap of events. Argument: :del the range of email, sms and trap of events, syntax 1,5-7, available from 1 to 25 Possible value: : 1~25 Example: 065-7727S(alarm-events)# del all 1-3 del email Syntax: del email Description: To disable the email of the events.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch del trap Syntax: del trap Description: To disable the trap of the events. Argument: :del the range of trap, syntax 1,5-7, available from 1 to 25 Possible value: : 1~25 Example: 065-7727S(alarm-events)# del trap 1-3 set all Syntax: set all Description: To enable email, sms and trap of events.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set sms Syntax: set sms Description: To enable the sms of the events. Argument: :set the range of sms, syntax 1,5-7, available from 1 to 25 Possible value: : 1~25 Example: 065-7727S(alarm-events)# set sms 1-3 set trap Syntax: set trap Description: To enable the trap of the events.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 STP Topology Changed STP Disabled STP Enabled LACP Disabled LACP Enabled LACP Member Added LACP Port Failure GVRP Disabled GVRP Enabled Port-based Vlan Enabled Tag-based Vlan Enabled Metro-mode Vlan Enabled Module Inserted Module Removed Dual Media Swapped Looping Detected IP-MAC Binding Offered IP-MAC Binding Released v show (alarm) Syntax: show Description: The Show for alarm here is used to di
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 User Logout STP Topology Changed STP Disabled STP Enabled LACP Disabled LACP Enabled LACP Member Added LACP Port Failure GVRP Disabled GVRP Enabled Port-based Vlan Enabled Tag-based Vlan Enabled Metro-mode Vlan Enabled Module Inserted Module Removed Dual Media Swapped Looping Detected IP-MAC Binding Offered IP-MAC Binding Released v 065-7727S (alarm)# show sms SMS Server : Username : Password :
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch <> del phone-number Syntax: del phone-number <#> Description: To delete sms phone number. Argument: <#>: mobile phone number, range: 1 to 6 Possible value: <#>: 1 to 6 Example: 065-7727S(alarm-sms)# del phone-number 3 del server-user Syntax: del server-user Description: To delete sms server, user account and password. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Mobile Mobile Mobile Mobile Phone Phone Phone Phone 3: 4: 5: 6: set server Syntax: set server Description: To set up the IP address of sms server. Argument: : SMS server ip address or domain name Possible value: None. Example: 065-7727S(alarm-sms)# set server 192.168.1.7 065-7727S(alarm-sms)# show SMS Server : 192.168.1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Mobile Mobile Mobile Mobile Mobile Mobile Phone Phone Phone Phone Phone Phone 1: 0910380190 2: 3: 4: 5: 6: show Syntax: show Description: To display the configuration of SMS trap event. Argument: None. Possible value: None. Example: 065-7727C(alarm-sms)# show SMS Server : 192.168.1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch autologout autologout Syntax: autologout
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 1024000 1024000 3776 3776 3776 3776 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 1024000 1024000 DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE 10240
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 102400 102400 102400 102400 102400 102400 102400 102400 19520 19520 19520 19520 102400 102400 102400 102400 102400 102400 1024000 1024000 102400 3776 3776 3776 3776 3776 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 1024000 1024000 DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISA
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch ====== ================== ================= ============ ================ ….
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 102400 102400 102400 102400 102400 102400 102400 102400 19520 19520 19520 19520 102400 102400 102400 102400 102400 102400 1024000 1024000 102400 3776 3776 3776 3776 3776 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 102400 1024000 1024000 Publication date: March,2008 Revision A1 188 DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE DISAB
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch config-file export start Syntax: export start Description: To run the export start function. Argument: None. Possible value: None. Example: 065-7727S (config-file)# export start Export successful. export user-conf Syntax: export user-conf Description: To run the export user-conf function. Argument: None. Possible value: None. Example: 065-7727S (config-file)# export user-conf Export successful.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch import user-conf Syntax: import user-conf Description: To run the import user-conf function. Argument: None. Possible value: None. Example: 065-7727S (config-file)# import user-conf Import successful. set export-path Syntax: set export-path Description: To set up the file path and filename that user would like to export.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show Syntax: show Description: To display the information of the config file. Argument: None. Possible value: None. Example: 065-7727S(config-file)# show TFTP Server IP Address: 192.168.3.111 Export Path and Filename: log/21511.txt Import Path and Filename: log/21511.txt dhcp-boot set Syntax: set Description: To set up the delay time for DHCP Boot. Argument: :range syntax: 0, 1-30.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch diag <> disable Syntax: disable Description: Disable auto ping function on switch Argument: None. Possible value: None. Example: 065-7727S (diag-autoping)# disable enable Syntax: enable Description: Enable auto ping function on switch Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 065-7727S(diag-autoping)# show Auto Ping state :Enabled IP address :192.168.2.22 Interval(sec) :100 Times :3 065-7727S(diag-autoping)# show Syntax: show Description: To show auto ping function on switch Argument: none Possible value: none Example: 065-7727S(diag-autoping)# show Auto Ping state :Enabled IP address :192.168.2.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch diag Syntax: diag Description: Diag is used to test whether EEPROM, UART, DRAM and Flash is normal or not. Argument: None. Possible value: None. Example: 065-7727S (diag)# diag EEPROM Test : OK UART Test : OK DRAM Test : OK Flash Test : OK Loopback Syntax: loopback Description: For Internal/External Loopback Test. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 192.168.2.22 is alive. 065-7727S(diag)# firmware set upgrade-path Syntax: set upgrade-path Description: To set upgrade file path and name on switch. Argument: : upgrade file path and name Possible value: : upgrade file path and name Example: 065-7727S (firmware)# set upgrade-path ruby_es2226_v0.99.img show Syntax: show Description: To display the information of tftp server and upgrade-path and file name.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch gvrp disable Syntax: disable Description: To disable the gvrp function Argument: None. Possible value: None. Example: 065-7727S (gvrp)# disable enable Syntax: enable Description: To enable the gvrp function. Argument: None. Possible value: None. Example: 065-7727S (gvrp)# enable group Syntax: group Description: To enter any of gvrp group for changing gvrp group setting.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 065-7727S (gvrp)# group 2 065-7727S (gvrp-group-2)# set applicant 1-6 non-participant 065-7727S (gvrp-group-2)# show GVRP group VID: 2 Port Applicant Registrar ---- --------------- --------1 Non-Participant Normal 2 Non-Participant Normal 3 Non-Participant Normal 4 Non-Participant Normal 5 Non-Participant Normal 6 Non-Participant Normal 7 Normal Normal 8 Normal Normal 12 Normal Normal 13 Normal Normal : : 23 Normal Normal 24 Normal Normal 25 Normal N
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set applicant Syntax: set applicant Description: To set default applicant mode for each port.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Example: 065-7727S (gvrp)# set restricted 1-10 enable 065-7727S (gvrp)# show config GVRP state: Enable Port Join Time Leave Time LeaveAll Time ---- --------- ---------- ------------1 20 60 1000 2 20 60 1000 3 20 60 1000 4 20 60 1000 5 20 60 1000 6 20 60 1000 7 20 60 1000 8 20 60 1000 9 20 60 1000 10 20 60 1000 22 23 24 25 26 20 20 20 20 20 60 60 60 60 60 1000 1000 1000 1000 1000 Applicant --------------Normal Normal Normal Normal Normal Normal N
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show config Syntax: show config Description: To display the gvrp configuration. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show group Syntax: show group Description: To show the gvrp group. Argument: None. Possible value: None. Example: 065-7727S(gvrp)# show group GVRP group information Current Dynamic Group Number: 0 VID Member Port ---- -------------------------------------------------- hostname hostname Syntax: hostname Description: To set up the hostname of the switch. Argument: : hostname, max. 40 characters. Possible value: : hostname, max.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Possible value: : from 1 to 4094 value. : ip address format. : ip address format. syntax: 1,5-7, from 1 to 26 value. Example: 065-7727S(multicast)# add group-filter 2 224.1.1.1 230.255.255.255 10-15 065-7727S(multicast)# show group-filtering 2 Index : 1 Start Address : 224.1.1.1 End Address : 230.255.255.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 065-7727S(multicast)# show group-filtering 2 None entry exist. 065-7727S(multicast)# delete igmp-vlan Syntax: delete igmp-vlan Description: To delete igmp-vlan function on switch. Argument: : from 1 to 4094 value. Possible value: : from 1 to 4094 value.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Start Address : 224.1.1.1 End Address : 225.255.255.255 Port Member : 10,11,12,13,14,15 065-7727S(multicast)# edit group-filter 3 1 224.1.1.1 226.255.255.255 1011 065-7727S(multicast)# show group-filtering 3 Index : 1 Start Address : 224.1.1.1 End Address : 226.255.255.255 Port Member : 10,11 set unregfld-enable Syntax: set unregfld-enable Description: To set unregister multicast flooding state function on switch.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch ...(q to quit) set gnlqry-interval Syntax: set gnlqry-interval Description: To set general query interval function on switch. Argument: : from 1 to 2000 value. Possible value: : 1 to 2000 . Example: 065-7727S(multicast)# set gnlqry-interval 20 set gnlqry-response Syntax: set gnlqry-response Description: To set general query max response time Argument: : from 1 to 10 value. Possible value: : 1 to 10 .
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set group-limit Syntax: set group-limit Description: To set multicast group limit Argument: syntax: 1,5-7, from 1 to 26 value. : from 0 to 256 value Possible value: : 1 to 26. : 0 to 256.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Possible value: : 0(disable), 1(enable).
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch General Query Max Response Time General Query Timeout Specific Query Count Specific Query Max Response Time Specific Query Timeout : : : : : 5 15 2 1 2 Port Multicast Group Limit IGMP Router ---- --------------------- ----------1 256 2 256 3 256 4 256 5 256 v 6 256 v 7 256 v 8 256 9 256 10 55 v 11 55 v 12 55 v ...
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch : 1 to 26. : 0(untag-out), 1(tag-out) Example: 065-7727S(multicast)# set mvr-tagging 8-10 1 065-7727S(multicast)# show mvr-setting Multicast VLAN Registration : Enable MMulticast VLAN ID : 0 Port Service Type Tagging ---- ------------ ------1 None 2 None 3 None 4 None 5 None 6 None 7 None 8 None v 9 None v 10 None v 11 None 12 None 13 None 14 None 15 None 16 None 17 None 18 None ...
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set mvrserv-type Syntax: set mvrserv-type Description: To set mvr service type Argument: syntax: 1,5-7, from 1 to 26 value. : 0(None), 1(Client), 2(Router). Possible value: : 1 to 26. : 0(None), 1(Client), 2(Router).
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set specqry-count Syntax: set specqry-count Description: To set specific query count function on switch Argument: : from 1 to 10 value. Possible value: : from 1 to 10 value. Example: 065-7727S(multicast)# set specqry-count 5 set specqry-response Syntax: set specqry-response
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Port Multicast Group Limit IGMP Router ---- --------------------- ----------1 256 2 256 3 256 4 256 5 256 v 6 256 v 7 256 v 8 256 9 256 10 55 v 11 55 v 12 55 v ...(q to quit) show group-filtering Syntax: show group-filtering Description: To show group filtering on switch. Argument: : from 1 to 4094 value. Possible value: : 1 to 4094. Example: 065-7727S(multicast)# show group-filtering 3 Index :1 Start Address : 224.1.1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch IGMP Snooping Unregister Multicast Flooding General Query Interval General Query Max Response Time General Query Timeout Specific Query Count Specific Query Max Response Time Specific Query Timeout : : : : : : : : Enable Enable 20 5 15 5 1 20 Port Multicast Group Limit IGMP Router ---- --------------------- ----------1 256 2 256 3 256 4 256 5 256 v 6 256 v 7 256 v 8 256 9 256 10 55 v 11 55 v 12 55 v ...
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show multicast-status Syntax: show multicast-status Description: To show multicast-status on switch. Argument: none Possible value: none Example: 065-7727S(multicast)# show multicast-status ? None entry exist. 065-7727S(multicast)# show mvr-setting Syntax: show mvr-setting Description: To show mvr-setting on switch.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 15 None 16 None 17 None 18 None ...(q to quit) IP disable dhcp Syntax: disable dhcp Description: To disable the DHCP function of the system. Argument: None. Possible value: None. Example: 065-7727S(ip)# disable dhcp DHCP is already stopped. enable dhcp Syntax: enable dhcp Description: To enable the system DHCP function and set DNS server via manual or auto mode. Argument: : set DNS by using manual or auto mode.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set ip Syntax: set ip Description: To set the system IP address, subnet mask and gateway. Argument: : ip address : subnet mask : default gateway Possible value: : 192.168.1.1 or others : 255.255.255.0 or others : 192.168.1.253 or others Example: 065-7727S (ip)# set ip 192.168.1.2 255.255.255.0 192.168.1.253 065-7727S(ip)# show DHCP : Disable IP Address : 192.168.1.2 Subnet mask : 255.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch log clear Syntax: clear Description: To clear the log data. Argument: None. Possible value: None. Example: 065-7727S (log)# clear disable auto-upload Syntax: disable auto-upload Description: To disable the auto-upload function. Argument: None. Possible value: None. Example: 065-7727S (log)# disable auto-upload enable auto-upload Syntax: enable auto-upload Description: To enable the auto-upload function. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show Syntax: show Description: To show a list of trap log events. When any of log events happens, it will be recorded and using show command in log function to query. Up to 120 log records are supported. Argument: None. Possible value: None. Example: 065-7727S(log)# show Tftp Server : 192.168.2.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch mac-table <> del Syntax: del Description: To delete the mac alias entry. Argument: : mac address, format: xx-xx-xx-xx-xx-xx Possible value: : mac address Example: 065-7727S(mac-table-alias)# del 00-e5-55-c9-93-c9 set Syntax: set Description: To set up the mac alias entry. Argument: : mac address, format: xx-xx-xx-xx-xx-xx : mac alias name, max.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch <> search Syntax: search Description: To look for the relative mac information in mac table.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch <> flush Syntax: flush Description: To flush MAC table. Argument: none Possible value: none Example: 065-7727S(mac-table-maintain)# flush set aging Syntax: set aging
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show Syntax: show Description: To display the settings of MAC table ageout time and the learning limit of each port. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch enable Syntax: enable Description: To enable port security. Argument: none Possible value: none Example: 065-7727S(mac-table-port-security)# enable <> Syntax: port Description: To enter into per port static mac mode.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch <> add Syntax: add Description: To add the static mac entry.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show Syntax: show Description: To display static mac entry. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 0 - Any Possible value: : management security entry name syntax: 1,1-3, available from 0 to 3 1 - Http 2 - Telnet 3 - Snmp 0 - Any Example: 065-7727S(management)# set access acc2 1-3 065-7727S(management)# show 1): Name : acc1 VID : 2 IP Range: 192.168.2.2-192.168.2.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch IP Range: Port : Access : Action : 192.168.2.2-192.168.2.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set port Syntax: set port Description: To setup port field of a management security entry Argument: : management security entry name : 1,5-7, available from 0 to 26, 0 for any Possible value: : management security entry name : 1,5-7, available from 0 to 26, 0 for any Example: 065-7727S(management)# set port remote1 9 065-7727S(management)# show 1): Name : remote1 VID : Any IP Range: 192.168.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Access : Any Action : Deny 065-7727S(management)# show Syntax: show Description: To show management security entry. Argument: None Possible value: None. Example: 065-7727S(management)# show 1): Name : remote1 VID : 300 IP Range: 192.168.2.33-192.168.2.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch port clear counter Syntax: clear counter Description: To clear all ports’ counter (include simple and detail port counter) information. Argument: None. Possible value: None. Example: 065-7727S (port)# clear counter disable state Syntax: disable state Description: To disable the communication capability of the port.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set description Syntax: set description Description: To set up the flow control function of all ports.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set speed-duplex Syntax: set speed-duplex |[<10|100|1000> ] Description: To set up the speed and duplex of all ports.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show conf Syntax: show conf Description: To display the each port’s configuration about state, speed-duplex and flow control. Argument: None. Possible value: None. Example: 065-7727S (port)# show conf ……. …….
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Example: 065-7727S (port)# show detail-counter 6 065-7727S(port)# show detail-counter 1 Receive Total: ------------------------------------------------------Rx Packets : 61731 Rx Octets : 54949069 Rx Errors : 0 Rx Unicast Packets : 42150 Rx Broadcast Packets : 12752 Rx Multicast Packets : 6829 Rx Pause Packets : 0 Receive Size Counters: ------------------------------------------------------Rx Undersize Packets : 0 Rx Oversize Packets : 0 Receive Erro
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Vendor PN Vendor Rev Vendor SN Date Code Temperature Vcc Mon1 (Bias) mA Mon2 (TX PWR) Mon3 (RX PWR) : : : : : : : : : FTM-C012R-LC 10 PP220052901281 051012 none none none none none 065-7727S(port)# show simple-counter Syntax: show simple-counter Description: To display the summary counting of each port’s traffic. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show status Syntax: show status Description: To display the port’s current status. Argument: None. Possible value: None. Example: 065-7727S(port)# show status Port Media Link State Auto Nego.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch qos disable 1p Syntax: disable 1p Description: To disable 802.1p qos. Argument: None. Possible value: None. Example: 065-7727S (qos)# disable 1p disable dscp Syntax: disable dscp Description: To disable IP DSCP qos. Argument: None. Possible value: None. Example: 065-7727S (qos)# disable dscp disable qos Syntax: disable qos Description: To disable qos function. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch enable 1p Syntax: enable 1p Description: To enable 802.1p qos. Argument: None. Possible value: None. Example: 065-7727S (qos)# enable 1p enable dscp Syntax: enable dscp Description: To enable IP DSCP qos. Argument: None. Possible value: None. Example: 065-7727S (qos)# enable dscp enable qos Syntax: enable qos Description: To enable qos function. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch enable tos Syntax: enable tos Description: To enable IP TOS qos. Argument: None. Possible value: None. Example: 065-7727S (qos)# enable tos set dscp Syntax: set dscp [] [] [] [] Description: To set IP DSCP qos weighting for 4 queues. Argument: : queue level, q0: queue 0; q1: queue 1; q2: queue 2; q3: queue 3 : priority level. One queue has been assigned 2 different priorities.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch ==================== Global QoS mode: Enable QoS Enable 802.1p Priority Enable ip diffserv classification Scheduling: 4 WRR method. weight: wrr 0 = 1; wrr 1 = 2; wrr 2 = 4; wrr 3 = 8. weighted range: 1~55. P0~7: Priority 0~7. Default mode: Queue0: P0,P1; Queue1: P2,P3; Queue2: P4,P5; Queue3: P6,P7.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch P0 P1 P2 P3 P4 P5 P6 P7 ---- ---- ---- ---- ---- ---- ---- ---Queue 0 1 2 3 1 2 3 3 065-7727S(qos)# Possible value: show dscp Syntax: show dscp Description: To show IP DSCP Qos configuration. Argument: None. Possible value: None. Example: 065-7727S (qos)# show dscp ip diffserv classification ==================== Global QoS mode: Enable QoS Disable 802.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 44 48 52 56 60 2 3 3 3 3 45 49 53 57 61 2 3 3 3 3 46 50 54 58 62 2 3 3 3 3 47 51 55 59 63 show priority-tag Syntax: show priority-tag Description: To show 802.1p Qos configuration. Argument: None. Possible value: None. Example: 065-7727S (qos)# show priority-tag 802.1p priority ==================== Global QoS mode: Enable QoS Enable 802.1p Priority Enable ip diffserv classification Scheduling: 4 WRR method.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch reboot reboot Syntax: reboot Description: To reboot the system. Argument: None. Possible value: None. Example: 065-7727S # reboot security <> set Syntax: set Description: To set up the function of the isolated group.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Example: 065-7727S(security-isolated-group)# set 9,10-14 065-7727S(security-isolated-group)# show Isolated group: 9 10 11 12 13 14 065-7727S(security-isolated-group)# <> disable Syntax: disable Description: To disable the function of mirror. Argument: None. Possible value: None. Example: 065-7727S (security-mirror)# disable enable Syntax: enable Description: To enable the function of mirror. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set ingress/egress to 0 as ingress/egress disabled Possible value: : 0 to 26 : 0 to 26 Example: 065-7727S(security-mirror)# set 9 1-10 1-10 065-7727S(security-mirror)# show Mirror: Monitoring Port :9 Monitored Ingress : Monitored Egress : 065-7727S(security-mirror)# show Syntax: show Description: To display the current setting status of mirror. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch snmp disable Syntax: disable set-community disable snmp Description: The Disable here is used for the de-activation of snmp or set-community. Argument: None. Possible value: None. Example: 065-7727S(snmp)# disable set-community 065-7727S(snmp)# disable snmp enable Syntax: enable set-community enable snmp Description: The Enable here is used for the activation snmp or set-community. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Example: 065-7727S (snmp)# set get-community public 065-7727S (snmp)# set set-community private 065-7727S (snmp)# set trap 1 192.168.1.1 162 public show Syntax: show Description: The Show here is to display the configuration of SNMP. Argument: None. Possible value: None. Example: 065-7727S (snmp)# show SNMP : Enable Get Community: public Set Community: private [Enable] Trap Host 1 IP Address: 192.168.1.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch stp MCheck Syntax: MCheck Description: To force the port to transmit RST BPDUs. Argument: : syntax 1,5-7, available from 1 to 26 Possible value: : 1 to 26 Example: 065-7727S (stp)# Mcheck 1-8 disable Syntax: disable Description: To disable the function of STP. Argument: None. Possible value: None. Example: 065-7727S (stp)# disable enable Syntax: enable Description: To enable the function of STP. Argument: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set config Syntax: set config Description: To set up the parameters of STP. Argument: : priority must be a multiple of 4096,available from 0 to 61440. : available from 1 to 10. : available from 6 to 40. : available from 4 to 30. Note: 2*(Forward Delay -1) >= Max Age Max Age >= 2*(Hello Time +1) Possible value: : 0 to 61440.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Possible value: :stp / rstp Example: 065-7727S (stp)# set version rstp show config Syntax: show config Description: To display the STP configuration data. Argument: None. Possible value: None. Example: 065-7727S (stp)# show config STP State Configuration : Spanning Tree Protocol : Enabled Bridge Priority (0-61440) : 61440 Hello Time (1-10 sec) : 2 Max.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 24 DISCARDING 25 DISCARDING 26 DISCARDING 200000 20000 20000 128 128 128 No No No Auto Auto Auto show status Syntax: show status Description: To display of the status of STP. Argument: None. Possible value: None. Example: 065-7727S (stp)# show status STP Status : STP State Bridge ID Bridge Priority Designated Root Designated Priority Root Port Root Path Cost Current Max.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch system set contact Syntax: set contact Description: To set the contact description of the switch. Argument: :string length up to 40 characters. Possible value: : A, b, c, d, ... ,z and 1, 2, 3, …. etc. Example: 065-7727S (system)# set contact Taipei set device-name Syntax: set device-name Description: To set the device name description of the switch.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show Syntax: show Description: To display the basic information of the switch. Argument: None. Possible value: None. Example: 065-7727S(system)# show Model Name : 065-7727S System Description : 24 Fast Ethernet + 2 Gigabit L2 Managed Switch Location : Contact : Device Name : 065-7727S System Up Time : 0 Days 22 Hours 29 Mins 31 Secs Current Time : Wed Aug 31 14:03:33 2005 BIOS Version : v1.03 Firmware Version : v2.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch tftp set server Syntax: set server Description: To set up the IP address of tftp server. Argument: : the IP address of tftp server Possible value: : tftp server IP Example: 065-7727S (tftp)# set server 192.168.3.111 show Syntax: show Description: To display the information of tftp server. Argument: None Possible value: None Example: 065-7727S (tftp)# show Tftp Server : 192.168.3.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch time set daylightsaving Syntax: set daylightsaving
Description: To set up the daylight saving.Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch : (2000-2036) : (01-12) - : (01-31) : (00-23) : (00-59) : (00-59) Example: 065-7727S(time)# set manual 2008/04/08 11:24:00 065-7727S(time)# show Current Time : Tue Apr 08 11:24:02 2008 NTP Server : 209.81.9.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Timezone Day light Day light Day light 065-7727S : Saving : Saving Start: Saving End : (time)# 8 4 Hours Mth: 2 Day: 20 Hour: 10 Mth: 3 Day: 20 Hour: 10 Publication date: March, 2008 Revision A1 257
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch trunk del trunk Syntax: del trunk Description: To remove the trunk port. Argument: : syntax 1,5-7, available from 1 to 26 Possible value: : 1 to 26 Example: 065-7727S (trunk)# del trunk 1 set hash Syntax: set hash Description: To set up trunk hash method. Argument: : lacp hash method 0: DA and SA 1: SA 2: DA Note : This hash method applies to both LACP and static trunk.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set trunk Syntax: set trunk Description: To set up the status of trunk, including the group number and mode of the trunk as well as LACP mode. Argument: : syntax 1,5-7, available from 1 to 26 : static : adopt the static link aggregation lacp : adopt the dynamic link aggregation- link aggregation control protocol : 1-3.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show lacp-config Syntax: show lacp-config Description: To display the value of LACP Priority. Argument: None. Possible value: None. Example: 065-7727S (trunk)# show lacp-config LACP System Priority : 33333 Hash Method : DA show lacp-detail Syntax: show lacp-detail Description: To display the detailed information of the LACP trunk group.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch show status Syntax: show status Description: To display the aggregator status and the settings of each port. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch vlan del port-group Syntax: del port-group Description: To delete the port-based vlan group. Argument: : port-vlan name Possible value: : port-vlan name Example: 065-7727S (vlan)# del port-group vlan-2 del tag-group Syntax: del tag-group Description: To delete the tag-based vlan group.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch disable drop-untag Syntax: disable drop-untag Description: To disable drop-untag. Argument: : which port(s) you want not to drop untagged frames. Syntax: 1,5-7, available from 1 to 26 Possible value: : 1 to 26 Example: 065-7727S (vlan)# disable drop-untag 2,4,5-7 disable svl Syntax: disable svl Description: To enable Independent VLAN Learning. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch enable double-tag Syntax: enable double-tag Description: To enable double-tag. Argument: None. Possible value: None. Example: 065-7727S (vlan)# enable double-tag enable drop-untag Syntax: enable drop-untag Description: To enable drop-untag. Argument: : which port(s) you want to drop untagged frames.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch enable symmetric Syntax: enable symmetric Description: To drop frames from the non-member port. Argument: None. Possible value: None. Example: 065-7727S (vlan)# enable symmetric set mgt-vlan Syntax: set mgt-vlan [vid] Description: To set management vlan function on switch..
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 2: 25 and 26 port Possible value: : set tag-based vlan t: set port-based vlan : set metro mode vlan #: up-link port type 0: 25 port 1: 26 port 2: 25 and 26 port Example: 065-7727S(vlan)# set mode tag 0 set port-group Syntax: set port-group Description: To add or edit a port-based vlan group.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set tag-group Syntax: set tag-group Description: To add or edit the tag-based vlan group.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Example: 065-7727S (vlan)# show group Vlan mode is tag-based. 1) Name :default VID :1 Member:1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Untag :1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 2) Name :VLAN-2 VID :2 Member:2 3 4 5 6 13 14 15 Untag : show pvid Syntax: show pvid Description: To display pvid, priority and drop untag result.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 20 21 22 23 24 25 26 1 1 1 1 1 1 1 0 0 0 0 0 0 0 Disable Disable Disable Disable Disable Disable Disable Publication date: March, 2008 Revision A1 269
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch vs disable Syntax: disable Description: To disable the virtual stack. Argument: None. Possible value: None. Example: 065-7727S(vs)# disable enable Syntax: enable Description: To enable the virtual stack. Argument: None. Possible value: None. Example: 065-7727S (vs)# enable set gid Syntax: set gid Description: To set the group id.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch set role Syntax: set role Description: To set role. Argument: : master: act as master, slave : act as slave Possible value: : master or slave Example: 065-7727S (vs)# set role master show Syntax: show Description: To display the configuration of the virtual stack. Argument: None. Possible value: None.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch 5. Maintenance 5-1. Resolving No Link Condition The possible causes for a no link LED status are as follows: z The attached device is not powered on z The cable may not be the correct type or is faulty z The installed building premise cable is faulty z The port may be faulty 5-2. Q&A 1. Computer A can connect to Computer B, but cannot connect to Computer C through the Managed Switch. 9 The network device of Computer C may fail to work.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Appendix A Technical Specifications Features • The switch included 24-Port 10/100Mbps TP and 2-Port Gigabit Dual Media TP/SFP or TP/GBIC. • Supports 24-port 10/100M TP ports with Nway and auto MDIX function. • 065-7727S supports 2 Gigabit dual media ports(TP/SFP) and 2 slots for removable SFP module supporting 1000M SFP fiber module. • • • • • • • • Supports on-line plug/unplug SFP transceiver modules.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Hardware Specifications Standard Compliance: IEEE802.3ab / 802.3z / 802.3u / 802.3x 802.3z and 802.3ab compliant Gigabit Ethernet ports Network Interface of Option transceiver: Configuration SFP.0LC.202 SFP.0LC.212.XX SFP.0BL.621.
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Diagnostic LED: System LED : Power CPURUN ACT (LEDSET) FDX (LEDSET) SPD (LEDSET) Per Port LED: 10/100M TP Port 1 to 24 1000M Fiber/TP Port 25,26 Power Requirement : : LINK/ACT, FDX, SPD : LINK/ACT, FDX, SPD AC Line Voltage : 100∼240 V Frequency : 50∼60 Hz Consumption : 15W Ambient Temperature : 0° to 40°C : 5% to 90% Humidity Dimensions : 44(H) × 442(W) × 209(D) mm Comply with FCC Part 15 Class A & CE Mark Approval Publication d
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Management Software Specifications System Configuration Management Agent Spanning Tree Algorithm VLAN Function Trunk Function IGMP Bandwidth Control Quality of Service (QoS) Port Security Internetworking Protocol Network Management Auto-negotiation support on 10/100Base-TX ports, Web browser or console interface can set transmission speed (10/100Mbps) and operation mode (Full/Half duplex) on each port, enable/disable any port, set VLAN group,
Signamax™ 065-7727S 24-Port 10/100BaseT/TX Managed Switch Appendix B Null Modem Cable Specifications The DB-9 cable is used for connecting a terminal or terminal emulator to the Managed Switch’s RS-232 port to access the command-line interface. The table below shows the pin assignments for the DB-9 cable.
