8 Port Nway Fast Ethernet Web Smart Switch Model: 065-7508 User‘s Guide
FCC Warning This device has been tested and found to comply with limits for a Class B digital device, pursuant to Part 2 and 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Introduction 065-7508 switch provides 8 10/100M ports. 065-7508 switch was designed for easy installation and high performance in an environment where traffic is on the network and the number of users increases continuously. The small palm size with transparent plastic case was specifically designed for small to medium workgroups. 065-7508 switch can be installed where space is limited; moreover, it provides smooth network migration and easy upgrade to network capacity. SIGNAMAX LLC • www.signamax.
Package Contents Before you start to install this switch, please verify your package that contains the following items: One 065-7508 Fast Ethernet Switch One Power Adapter One CD with User’s Manual Note: If any of these items is found missing or damaged, please contact your local supplier for replacement. SIGNAMAX LLC • www.signamax.
Key Features 8 Port 10/100M Nway (Auto-negotiation) Switch Palm size with plastic case Auto-learn of networking configurations Auto-detect full/half-duplex modes for any port Dedicated full-duplex 200Mbps bandwidth Store-and-Forward switching methods IEEE 802.
Front Panel (LEDs) LED Indicators of 8 Port 10/100M Switch LED Power Status On Off LINK/ACT On Off Flashing Operation Power is on. Power is off. Port is for connection No connection. Data is transmitting or receiving. Rear Panel (Connections) Switch/Hub to 065-7508 Fast Ethernet Switch This switch provides automatic crossover detection functionality for any port. It is simple and friendly to up-link to another switch without crossover cable. SIGNAMAX LLC • www.signamax.
PC/Other devices to 065-7508 Fast Ethernet Switch Via a twisted pair cable straight through, this switch can be connected to PCs, servers and other network devices. Technical Specifications Standards Features Filtering/Forwarding Rates Transmission Media LED Indicators IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX IEEE 802.3x Flow control Number of Ports: 8 MAC Address: 1K Buffer Memory: 512K bits Transmission Method: Store and Forward 100Mbps port – 148,800pps 10Mbps – 14,880pps 10BaseT Cat.
Power Supply Power Consumption Dimensions Weight Operating Temperature Storage Temperature Humidity Certifications DC 7.5V/0.8A 6 Watts (Max) 140 x 105 x 25 mm (L x W x H) 224 g 0 to 55℃ -20 to 90℃ 10 to 90% RH (non-condensing) FCC Class B, CE Web Smart Switch Configure Please follow the steps to configure this Web Smart switch. Step 1: Use a twisted pair cable to connect this switch to your PC. Step 2: Set your PC’s IP to 192.168.2.xx. SIGNAMAX LLC • www.signamax.
Step 3: Open the web browser (like IE…), and go to 192.168.2.1 site, and then you will see the login screen. Key in the user ID and the password to pass the authentication, IP: 192.168.2.1 ID: admin Password: admin After the authentication procedure, the home page shows up. SIGNAMAX LLC • www.signamax.
Step 4: On the following home page, select the configuration by clicking the icon. It includes, - Administrator - Port Management - VLAN Setting - QoS Setting - Port Security - Logout SIGNAMAX LLC • www.signamax.
Administrator: Authentication Configuration You can change the user name and the password, and click “Update” to confirm the new change. After that, you can reset this switch by power off and then power on to take the new user name and the password effectively. SIGNAMAX LLC • www.signamax.
Administrator: System IP Configuration You can change the IP address by typing the new IP address and click “Update” to confirm the new change, and then the message will show “Setting Process OK!!”, After that, you should reset this switch by power off and then power on it to complete the new change. SIGNAMAX LLC • www.signamax.
Administrator: System Status It shows this switch MAC address and system version. You can change the new comment of this switch by typing the new comment and click “Update” to confirm the new change. SIGNAMAX LLC • www.signamax.
Administrator: Load Default Setting to EEPROM You can click “Load” to load the factory default setting, and then reset the switch by power off and then power on to take it effectively. Administrator: Firmware Update Follow the instruction on the screen to update the new firmware. Please contact with your sales agents to get the SIGNAMAX LLC • www.signamax.
latest firmware information. Port Management: Port Control Configuration Select the “Port No.” which you want to configure the mode below, “Link Capability” – you can select the port is Auto-Nego, 10M or 100M mode “Duplex” you can select the port is full or half-duplex mode. “TX & RX” - you can enable/disable the port. Note: The 1st port can’t be disabled. SIGNAMAX LLC • www.signamax.
Port Management: Bandwidth Control Select the “Port No.” which you want to configure the mode below, “TX Rate” is meant you can set the maximum transmission rate of this selected port and choose the full speed or in 128K/256K/512K/1M/2M/4M/8M speed. “RX Rate” is meant you can set the maximum receiving rate of this selected port and choose full speed or in 128K/256K/512K/1M/2M/4M/8M speed. SIGNAMAX LLC • www.signamax.
Port Management: Broadcast Storm Control You can enable or disable the broadcast storm protection feature by clicking “Update”. Port Management: Max Packet Length Select the maximum packet length setting, 1536 Bytes or 1522 Bytes for the switch. SIGNAMAX LLC • www.signamax.
VLAN Setting: Group VLAN setting There are 4 VLAN groups, 01, 02, 03, 04, can be used. Select a group, and then click the port number which you want to put it into the selected VLAN group. SIGNAMAX LLC • www.signamax.
VLAN Setting: Multi to 1 Setting This is a special design for easily setting the switch VLAN into “VLAN Per Port“. After this setting, all ports can only connect to the destination port. SIGNAMAX LLC • www.signamax.
QoS Setting: Class of Service Configuration You can set QoS mode of per port by different bases as below, “Port Base” – you can select the port which you want to configure as high priority and then the packets of the port will be firstly transmitted. “VLAN Tag/IP/DS” – you can select the port which you want to configure as packets with special Tag/IP will be firstly transmitted. SIGNAMAX LLC • www.signamax.
QoS Setting: High Priority Queue Configuration “Weight-Round-Robin” – WRR, you can set the ratio of the transmitting packet for the low priority to high priority. You can select WRR to be 1/4 or 1/8. QoS Setting: Customization Diffserv Please follow the instruction on the screen to update the setting. SIGNAMAX LLC • www.signamax.
Port Security When this function is enabled, the port will record the first receiving source MAC address as the security MAC address and only allow the packet which has the MAC address activating on the port. Logout: Click to logout SIGNAMAX LLC • www.signamax.
