24-Port 10/100 L3 Switch Model: 065-7434 Installation Guide Revision A1
Table of Contents OVERVIEW.......................................................................................................................... 2 PRODUCT FEATURES ........................................................................................................... 2 HARDWARE FEATURES ........................................................................................................ 4 Front Panel of 065-7434 Signamax 24-Port 10/100 L3 Switch ....................................
Overview 065-7434 Signamax 24-Port 10/100 L3 Switch provides telecom-level Ethernet access switches for operators. It supports next generation L2 and L3 features meets the requirements of customers for QoS, OAM, VPN, Multi-service and Protection. 065-7434 Signamax 24-Port 10/100 L3 switch can help customers develop IPTV, VoIP, VPN, wireless access and TDMoIP services.
065-7434 Signamax 24-Port 10/100 L3 Switch supports the PoE power supply of eight Ethernet interfaces for accessing wireless AP; provides eight E1/T1 interfaces (TDMoIP) to meet the requirement that operators access 2G base station service to IP network through E1/T1 interfaces, and access the traditional TDM devices such as PBX, realizing unified IP bearing; supports Ethernet fiber access for operators to access commercial customers.
three-color mode (srTCM) and dual-rate three-color mode (trTCM) to meet the SLA requirements of carriers, including CIR, CBS and PIR. L2/L3 multicast 065-7434 Signamax 24-Port 10/100 L3 Switch supports 1024 concurrent multicast data flow; IGMP snooping and IGMP fast-adding/leaving protocol.
TXD: the indicator for console/AUX port sending data; RXD: the indicator for console/AUX port receiving data; FET0-23 (100M Ethernet port) LINK: the indicator of Ethernet port link, which is always on when the link of Ethernet port is set up; ACT: the indicator of Ethernet port sending/receiving data, which is flashes when data is being sent or received; FEF8-23 (100M Ethernet port) LINK/ACT: the indicator of Ethernet port link, which is always on when the link of Ethernet port is set up and fla
Three alarm interfaces input/output Supports three alarm input signals and three alarm output signals Processor High-speed MIPS32 processor FLASH 32Mbytes SDRAM 128Mbytes Demission (W×D× H) 444x220x43.8mm Max. weight About 3.
SLA: CIR, PIR, CBS Priority mapping: the mapping among 802.
Supports IGMP fast adding/leaving; Supports MVR; Supports multicast ACL; The whole device supports 1024 multicast data flows; Authentication Supports IEEE 802.
Modules 065-7434 Signamax 24-Port 10/100 L3 Switch modules include one POE module and several kinds of AC/DC power modules. POE15-8PSE Module Ethernet Port Power Supply Control Module (POE15-8PSE) POE15-8PSE module is used by 065-7434 Signamax 24-Port 10/100 L3 Switch to control the power supply of up to 24-port Ethernet interface. Each Ethernet port provides up to 15W power. It serves as PSE and is inserted in 065-7434 Signamax 24-Port 10/100 L3 Switch chassis.
DC power: -46 ～-57V, 500W (only for the devices with POE function) The power modules for 065-7434 Signamax 24-Port 10/100 L3 Switch are as follows: Power Model AD150-1S007A Description 150W AC power module (inbuilt and can provide power for one POE15-8PSE module) 10 SIGNAMAX LLC • www.signamax.
Installation Preparations Security Suggestions To avoid the harms on persons and equipments caused by various accidents, comply with the following: Keep the switch far away from humid places and heat; Ensure that router is well grounded; Wear anti-static wrists during installation and maintenance, and ensure that the anti-static wrists contact well with the skins; Do not install, move and dismantle switches and modules during power on to avoid damages on persons and equipments; Do not ho
Temperature and Humidity To ensure the service quality and life of 065-7434 Signamax 24-Port 10/100 L3 Switch, it is recommended to maintain a certain temperature and humidity in the computer lab. If the humidity in the computer lab is high for long time, it causes the poor insulation and even electricity leak of insulation materials easily. Sometimes, the mechanical performances of materials change and the metal parts are corroded easily, too.
Apart from dust, the switch has strict requirements for SO2, H2S, NH3, and Cl2 in the room, because these harmful gases speed up the eroding of metals and the aging of some components. The specific limitations are as follows: Gas Maximum value (mg/m3) SO 0.2 2 HS 0.006 NH 0.05 2 Cl 3 0.01 2 Anti-static 065-7434 Signamax 24-Port 10/100 L3 switch takes lots of measures in anti-static, but when the static exceeds a certain volume, the circuits even the whole device are damaged.
The switch working place had better not be used with the grounding settings of power devices or anti-thunder grounding settings and the distance between them had better be as long as possible; Be away from the strong power radio transmitters, radar transmitter, and high frequency high-current equipments. Take electromagnetic shielding methods when necessary.
Cables in the package Equipment Configuration terminal (can be PC) HUB or Ethernet switch 15 SIGNAMAX LLC • www.signamax.
System Installation Preparations Tools Before installation, prepare slotted point screwdriver/cross screwdriver, level, ruler or tapeline, and anti-static equipment. point Check Cabinet Signamax devices are designed according to the dimension of 19-inch standard cabinet, so they can be installed and fixed normally on 19-inch standard cabinet.
The device must be installed on the pallets or trays (used in pairs) of the cabinet. Therefore, install the pallets or trays on the cabinet before installing the device as follows. Use the level to check whether the pallets or trays are horizontal. If not, adjust the fixed bolt of pallet or tray to make the pallet or tray horizontal and then fasten it. Pre-installed pallet or bracket Check whether the floating nut for fixing the device is installed in the square hole of the cabinet column.
Install Switch Install 065-7434 Signamax 24-Port 10/100 L3 switch in the cabinet: Step 1: Wear gloves and anti-static wrists, and make the anti-wrists well grounded; Step 2: Place the device on the fixed platform; make the installation holes of the brackets aim at the corresponding holes of the device sides; use the bolts to fix the brackets on the two sides of the device, as follows. Bracket Step 3: Make the front of the device face the operator.
Note Installation suggestions: When installing several devices on one cabinet, consider trying to install heavier devices at or close to the bottom of the cabinet on the premise of not affecting the whole cabling and layout. In this way, the gravity center of the cabinet is lowered and the stability is improved. When installing the device in the cabinet, it is recommended to reserve 1U space between the devices for dispersing the heat. Install the baffle boards between the devices.
Switch ground wire is the first guarantee of anti-thunder and antiinterference of the switch. It is required that users must connect the ground wires correctly. AC noise filter is connected to the AC input end of switch power supply, whose center is connected with chassis. The chassis ground (that is protect ground) must be connected to the ground, so as to make induction electricity and leaked electricity flow to the earth and improve the feature of anti electromagnetic interference.
1 2 3 Blue Black Kelly 1mm² 1mm² 1mm² －48V 0V Protection ground The following is the common AC power jack: Ground wire Naught wire Live wire Connect the power supply as follows: Step 1: Put the power supply switch to OFF. For AC switch, connect one side of AC power supply cable to the AC power input end of the back panel of the switch and another side to power supply jack; for DC switch, connect the power cable to the post according to the description of panel silk screen on the interface.
4) The modules can be dismantled as per the reverse order. Install POE15-8PSE (POE module) module 22 SIGNAMAX LLC • www.signamax.
Cables Ethernet Interface Cable Ethernet interface cable of 065-7434 Signamax 24-Port 10/100 L3 switch adopts 8-pin non-screen twisted pair. Silver plate 1 and 2 are the sending ends; silver plate 3 and 6 are the sending ends.
Cables of Interface Ethernet Optical The Ethernet optical interface cable of 065-7434 Signamax 24-Port 10/100 L3 Switch is the single-mode or multi-mode fiber of the LC interface. Console Port Cable 065-7434 Signamax 24-Port 10/100 L3 Switch Console port cable is connected with PC 9-pin serial jack, and it is 8-pin non-screen cable. One side is RJ45 plug and another is DB9 (hole).
RJ45-2BNC Interface Cable of E1/T1 E1/T1 interface uses RJ45-2BNC cable and the model is M1234-1372. The connection relation of E1/T1 interface cable Pin No.
3I3O Interface Cable The 3I3O input interface cable of 065-7434 Signamax 24-Port 10/100 L3 Switch is 8-pin non-screen twisted pair. The connection relation of RJ45 straight-through cable (type-5 twisted pair): RJ45 1&2 3&6 4&5 7&8 Signal Input1 Input2 Input3 Reserved Direction <— <— <— RJ45 1,2 3,6 4,5 7,8 Description Twisted-pair 1 Twisted-pair 2 Twisted-pair 3 Twisted-pair 4 The 3I3O output interface cable of 065-7434 Signamax 24-Port 10/100 L3 Switch is 8-pin non-screen twisted pair.
