Industrial Ethernet Extender Signamax Connectivity Systems Industrial Ethernet Extender Model - 065-1167 065-1167I 065-1167DIN 065-1167DINI User’s Guide 1
Industrial Ethernet Extender Quick Start Guide This quick start guide describes how to install and use the Ethernet Extender. The Ethernet Extender introduced here provides one channel for Ethernet over existing voice grade copper wire. Product Overview Product Features One 10/100BaseT/TX Ethernet port with RJ-45 connector Auto negotiation of speed and duplex mode on TX port Auto MDIX on TX port Complies with IEEE 802.3 10BaseT and IEEE 802.
Industrial Ethernet Extender Packing List When you unpack this product package, you will find the items listed below. Please inspect the contents, and report any apparent damage or missing items immediately to our authorized reseller.
Industrial Ethernet Extender Ethernet Extender Mode Settings Ethernet Extender mode settings are made very simple by means of a switch at the rear panel of the Ethernet Extender. The switch has two positions for Ethernet Extender mode settings. Refer to the table below for more details. One device must be set to Loc and the other to Rmt when two devices are connected.
Industrial Ethernet Extender Preface This manual describes how to install and use the Ethernet Extender. The Ethernet Extender introduced here provides one channel for Ethernet over existing voice grade copper wire. The Ethernet Extender fully complies with IEEE 802.3 10BaseT and IEEE 802.3u 100BaseTX standards.
Industrial Ethernet Extender Table of Contents Quick Start Guide .....................................................2 Product Overview............................................................2 Product Features .............................................................2 Packing List .....................................................................3 Ethernet Extender Mode Settings ...................................4 Front Panel & LEDs........................................................
Industrial Ethernet Extender Introduction The Ethernet Extender provides one channel for Ethernet over existing voice grade copper wire. It can be used as a stand-alone device or with a standard 19” chassis. Product Overview Product Features One 10/100BaseT/TX(TX) Ethernet port with RJ-45 connector Auto negotiation of speed and duplex mode on TX port Auto MDIX on TX port Complies with IEEE 802.3 10BaseT and IEEE 802.
Industrial Ethernet Extender One-Channel Ethernet Extender Ports The Ethernet Extender provides one TX port and one Ethernet Extender port. For the TX port, it uses RJ-45 connector and auto senses the speed of 10/100 Mbps. For the Ethernet Extender port, it uses RJ-11 connector and auto senses the speed of 1/3/5/10/15/20/25/30/40/50Mbps. Ethernet Extender Mode Settings Ethernet Extender mode settings are made very simple by means of a 2 position switch at the rear panel of the Ethernet Extender.
Industrial Ethernet Extender LEDs Pwr State Steady Off Indication Power on Pwr stands for POWER Power off Ethernet A valid Ethernet connection established Lnk stands for LINK Transmitting or receiving Ethernet data Lnk/Act Flashing Act stands for ACTIVITY Neither valid Ethernet connection established nor transmitting/receiving Ethernet Off data Ethernet Connection in full duplex mode Steady Fdx Fdx stands for FULL-DUPLEX Off Ethernet Connection in half-duplex mode Ethernet Extender Green The Ethernet Ex
Industrial Ethernet Extender Installation This chapter gives step-by-step installation instructions for the Ethernet Extender. Selecting a Site for the Equipment As with any electric device, you should place the equipment where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements: The ambient temperature should be between -20 to 60 degrees Celsius.
Industrial Ethernet Extender Installing in a Chassis The Ethernet Extender can be fit into any of the expansion slots on a special designed chassis. First, install the Ethernet Extender onto a carrier supplied with the chassis: Step 1- Unscrew the carrier from the desired expansion slot on the chassis. Step 2- Fit the Ethernet Extender onto the carrier.
Industrial Ethernet Extender When the Ethernet Extender is completely seated onto the carrier, insert the carrier to the guide rails of the expansion slot. Carefully slide in the carrier until it is fully and firmly fit the chassis. Fasten the screws onto the carrier. Never insert any Ethernet Extender into the chassis directly without using the supplied carriers.
Industrial Ethernet Extender Specifications Applicable Standards Fixed Ports Speed 10BaseT 100BaseTX Ethernet Extender Cable 10BaseT 100BaseTX Ethernet Extender Switching Method IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX Ethernet over VDSL 1 x 10/100Mbps Ethernet port with RJ-45 connector 1 x Ethernet Extender port with RJ-11 connector 10/20Mbps for half/full-duplex 100/200Mbps for half/full-duplex 1, 3, 5, 10, 15, 20, 25, 30, 40, 50Mbps 2-pair UTP/STP Cat. 3, 4, 5 2-pair UTP/STP Cat.
